EMJMN130Lenovo BT Wireless Mouse N130

User Guide model/型号: Lenovo N130 1. 打开上盖根据电池槽内的指示，指示放入电池，确保电池极别正确 Open the mouse’s top cover and install 1pcs AA battery, 2. 将下盖开关拨到”ON”位置，鼠标正面蓝色指示灯亮起 Remove the switch to “on” 3. 打开您电脑的蓝牙装置选择“添加设备” Open you PC’s Bluetooth chosen the “add device” 4. 按下鼠标背面的配对按钮 Press the Connection button User Guide model/型号: Lenovo N130 5. 电脑找到该鼠标，点击“下一步”按钮 When PC fined the mouse, click the “next” button 6. 配对完成 When you see below picture ,it mean pair finish. 7. 如果您是第一次安装，需要等待电脑自动安装驱动，这个过程大概需要等待1—2分钟，当您的电 脑出现“驱动安装成功”字样时，晃动您的鼠标，如果鼠标光标移动表示配对成功。 User Guide model/型号: Lenovo N130 8. If this is your first time use the mouse, please wait a moment, because your PC is searching the mouse’s driver. Move your mouse if the cursor can move at the same time, it’s mean your mouse paired success. 9. 如果鼠标光标不动，请重复上述1-7，并确保电池电量充足 If the cursor no action, please check your battery and repeat 1—8 set. User Guide model/型号: Lenovo N130 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Radiation Exposure Statement: The product comply with the US/Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. Responsible Party: Lenovo (United States) Incorporated 1009 Think Place-Building One Morrisville, NC 27560 Telephone: 1-919-294-5900

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: April 18, 2014 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID:EMJMN130 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Power of Attorney Date: April 18, 2014 T o whom it may concern: We, the undersigned PRIMAX ELECTRONICS LTD. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan Branch on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, -------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT

     

Page 2 Page 3 Page 4

Report No.: SA140411D20 1 of 6 Report Format Version 5.0.0 Reference No.: 140417D08 RF EXPOSURE REPORT REPORT NO.: SA140411D20 MODEL NO.: Lenovo N130 FCC ID: EMJMN130 RECEIVED: Apr. 17, 2014 TESTED: Apr. 17 ~ 18, 2014 ISSUED: Apr. 23, 2014 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA140411D20 2 of 6 Report Format Version 5.0.0 Reference No.: 140417D08 Table of Contents RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ........................................................................................................... 4 2. EVALUATION RESULT ................................................................................................. 5 3. SAR TEST EXCLUSION THRESHOLDS ..................................................................... 6 4. CONCLUSION .............................................................................................................. 6 Report No.: SA140411D20 3 of 6 Report Format Version 5.0.0 Reference No.: 140417D08 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140411D20 Original release. Apr. 23, 2014 Report No.: SA140411D20 4 of 6 Report Format Version 5.0.0 Reference No.: 140417D08 1.CERTIFICATION PRODUCT: Lenovo BT Wireless Mouse N130 BRAND: Lenovo MODEL NO.: Lenovo N130 APPLICANT: PRIMAX ELECTRONICS LTD. TESTED: Apr. 17 ~ 18, 2014 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: A pr. 23, 2014 ( Annie Chang / Supervisor ) APPROVED BY : , DATE: A pr. 23, 2014 ( Rex Lai / Assistant Manager ) Report No.: SA140411D20 5 of 6 Report Format Version 5.0.0 Reference No.: 140417D08 2. EVALUATION RESULT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where  f(GHz) is the RF channel transmit frequency in GHz .  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA140411D20 6 of 6 Report Format Version 5.0.0 Reference No.: 140417D08 3. SAR TEST EXCLUSION THRESHOLDS Maximum measured transmitter power: Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 1-g SAR test exclusion thresholds Result 2.402 ~ 2.480 0.4 5 0.124 3 Pass NOTE: 1. The antenna type is Printed antenna with -2.22dBi gain. 2. Calculate SAR test exclusion thresholds from conditi…

Text truncated - open the document above for the full version.

Report No.: RF140411D20 1 of 36 Report Format Version 5.0.1 Reference No.: 140417D08 FCC TEST REPORT REPORT NO.: RF140411D20 MODEL NO.: Lenovo N130 FCC ID: EMJMN130 RECEIVED: Apr. 17, 2014 TESTED: Apr. 17 ~ 18, 2014 ISSUED: Apr. 23, 2014 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF140411D20 2 of 36 Report Format Version 5.0.1 Reference No.: 140417D08 Table of Contents RELEASE CONTROL RECORD ................................................................................. 4 1. CERTIFICATION ............................................................................................... 5 2. SUMMARY OF TEST RESULTS ...................................................................... 6 2.1 MEASUREMENT UNCERTAINTY .................................................................... 6 3. GENERAL INFORMATION ............................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ................................................................. 7 3.2 DESCRIPTION OF TEST MODES ................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................... 9 3.3 DESCRIPTION OF SUPPORT UNITS ........................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................. 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................. 12 4. TEST TYPES AND RESULTS ........................................................................ 13 4.1 CONDUCTED EMISSION MEASUREMENT .................................................. 13 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ......................... 13 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ....... 13 4.2.2 TEST INSTRUMENTS .................................................................................... 14 4.2.3 TEST PROCEDURES .................................................................................... 15 4.2.4 DEVIATION FROM TEST STANDARD ........................................................... 15 4.2.5 TEST SETUP .................................................................................................. 16 4.2.6 EUT OPERATING CONDITIONS ................................................................... 16 4.2.7 TEST RESULTS ............................................................................................. 17 4.3 NUMBER OF HOPPING FREQUENCY USED ............................................... 21 4.3.1 LIMIT OF HOPPING FREQUENCY USED ..................................................... 21 4.3.2 TEST SETUP .................................................................................................. 21 4.3.3 TEST INSTRUMENTS .................................................................................... 21 4.3.4 TEST PROCEDURES .................................................................................... 21 4.3.5 DEVIATION FROM TEST STANDARD ........................................................... 21 4.3.6 TEST RESULTS ............................................................................................. 21 4.4 DWELL TIME ON EACH CHANNEL ............................................................... 23 4.4.1 LIMIT OF DWELL TIME USED ....................................................................... 23 4.4.2 TEST SETUP .................................................................................................. 23 4.4.3 TEST INSTRUMENTS .................................................................................... 23 4.4.4 TEST PROCEDURES .................................................................................... 23 4.4.5 DEVIATION FROM TEST STANDARD ........................................................... 23 4.4.6 TEST RESULTS ............................................................................................. 24 4.5 CHANNEL BANDWIDTH ................................................................................ 25 4.5.1 LIMITS OF CHANNEL BANDWIDTH .............................................................. 25 4.5.2 TEST SETUP .................................................................................................. 25 4.5.3 TEST INSTRUMENTS ......................................................................…

Text truncated - open the document above for the full version.

1 of 1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST