EMJMN700Lenovo dual mode Wireless touch mouse N700

Dual Mode WL Touch Mouse N700 1. Features No. Component 1 Left button 2 Touch Bar 3 Middle Button 4 Windows Button 5 LED Indicator 6 Right Button 7 Laser Projector 8 Switch for Bluetooth 4.0 BLE pairing, Bluetooth 4.0 mode and 2.4GHz mode 9 Battery cover Front view Rear view 2.Setting up your mouse 1) Open the battery cover and push it as shown 2) Take out the receiver 3) Insert two AAA batteries as shown 4) Close the battery cover as shown 3.Choose a use mode 1)The device has switched to presenter mode as shown 2)Rotate the bottom half of the device 180angle to switch to mouse mode as shown 4.choose a wireless transmission mode 1) Set up the device as shown and switch to2.4GHz wireless transmission mode 2) Set up the device as shown and switch toBT4.0BLE wireless transmission mode 5.Using your mouse 1)Mouse mode OS request: Windows XP, Windows Vista, Windows 7, Windows 8(The host needs to install Bluetooth 4.0 Chipset), Gesture Illustrations Function OS Up or down Scroll the page For all Windows OS Slide to left Open the charms Windows 8 Slide to right Switch APPs Windows 8 Press down Open Metro UI For all Windows OS 2) Presenter mode ＊Press down the Win or middle button to open or wake up presenter function. ＊Press down the left button to return the previous page. ＊Press down the right button to carry out the next page. ＊If no operation during 10 minutes ，product will be entered deep sleep mode and Win or middle button can activate it. 6. LED indicator ＊The green LED indicator will be illuminates when the device is switched from presenter mode to mouse mode or pairing successfully. ＊The red LED indicator will continuously flashes for approximately 9 seconds when the battery level is low. Replace the batteries immediately. FCC Statement United States of America Certification Number Mouse : Lenovo N700 Dongle: DGRFG4 FCC ID: EMJMN700 FCC ID: EMJDDGRFG4 FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help." FCC Caution: Changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Lenovo (United States) Incorporated 1009 Think Place-Building One Morrisville, NC 27560 Telephone: 1-919-294-5900 RF Exposure Statement The radiated energy from the Lenovo N700 Mouse/Dongle conforms to the FCC limit of the SAR (Specific Absorption Rate) requirement set forth in 47 CFR Part 2 section 1093 IC Statement Canada Certification Number Canada Numéro de Certification Mouse / souris: Lenovo N700 Dongle: DGRFG4 IC: 4251A-MN700 IC: 4251A-DGRFG4 Dongle Industry Canada Class B emission compliance statement Industry Canada, Class B "This Class "B" digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe "B" est conforme à la norme NMB-003 du Canada." Mouse / Dongle This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: 1) le dispositif ne doit pas produire de brouillage préjudiciable, et 2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable Low Power License-Exempt Radio Communication Devices (RSS-210) Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Permis d’émission à faible puissance – Cas des appareils de communications radio L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Exposure of humans to RF fields (RSS-102) The Lenovo N700 Mouse and Dongles Keyboard, Mouse, and Dongle employ low gain integral antennas that do not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site at http://www.hc-sc.gc.ca/ The radiated energy from the Lenovo Ultraslim Plus Wireless Keyboard, Mouse, and Dongle antennas conforms to the IC limit of the RF exposure requirement regarding IC RSS-102, Issue 4clause 4.1. Exposition des êtres…

Text truncated - open the document above for the full version.

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: July 25, 2013 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: EMJMN700 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Power of Attorney Date: July 25, 2013 T o whom it may concern: We, the undersigned PRIMAX ELECTRONICS LTD. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan Branch on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, -------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

*35MM *27MM Model: Lenovo N700 Name: Lenovo dual mode Wireless touch mouse N700 P/N: 888015450 Rating: 3V 40mA + - DB102306 + - S/N:OL15450YWWXXXXX Made in China Lenovo(Beijing) Limited IC: 4251A-MN700 Lenovo,Einsteinova 21, 851 01 Bratislava, Slovakia *35MM *27MM : Lenovo N700 P/N: 888015448 : 3V 40mA + - DB102306 + - S/N:OL15448YWWXXXXX IC: 4251A-MN700 CMIIT ID: XXXXXXXX Lenovo,Einsteinova 21, 851 01 Bratislava, Slovakia FCC ID: EMJMN700FCC ID: EMJMN700

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11

FCC ID: EMJMN700 Report No.: RF130705D03 Operational Description FOR 2.4GHz The transmitter of the EUT (Lenovo dual mode Wireless touch mouse N700) is powered by 3Vdc from batteries. The type of antenna is Printed antenna. The output power of this device is very low. Under normal use condition, the transmitter and the receiver are quite close, so high EIRP power is neither necessary nor allowed because of interference. FOR BLUETOOTH LE4.0 The device is operates in the 2.4GHz frequency spectrum with throughput of 1Mbps which DTS technique will be applied. The transmitter of the EUT is powered by 3Vdc from batteries. The antenna is Printed antenna. The other instruction, please have a look at the user’s manual.

Report No.: SA130705D03 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA130705D03 MODEL NO.: Lenovo N700 FCC ID: EMJMN700 RECEIVED: Jul. 5, 2013 TESTED: Jul. 13 ~ 19, 2013 ISSUED: Jul. 22, 2013 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA130705D03 2 of 6 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ........................................................................................................... 4 2. EVALUATION RESULT ................................................................................................. 5 3. SAR TEST EXCLUSION THRESHOLDS ..................................................................... 6 4. CONCLUSION .............................................................................................................. 6 Report No.: SA130705D03 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130705D03 Original release Jul. 22, 2013 Report No.: SA130705D03 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: Lenovo dual mode Wireless touch mouse N700 MODEL NO.: Lenovo N700 BRAND: Lenovo APPLICANT: PRIMAX ELECTRONICS LTD. TESTED: Jul. 13 ~ 19, 2013 TEST SAMPLE: MASS-PRODUCTION STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Jul. 22, 2013 ( Albee Chu / Specialist ) APPROVED BY : , DATE:Jul. 22, 2013 ( Ken Liu / Senior Manager ) Report No.: SA130705D03 5 of 6 Report Format Version 5.0.0 2. EVALUATION RESULT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where ¾ f(GHz) is the RF channel transmit frequency in GHz . ¾ Power and distance are rounded to the nearest mW and mm before calculation. ¾ The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA130705D03 6 of 6 Report Format Version 5.0.0 3. SAR TEST EXCLUSION THRESHOLDS Maximum measured transmitter power: Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 10-g extremity SAR test exclusion thresholds Result 2.402 ~ 2.480 0.7 5 0.217 7.5 Pass NOTE: 1. The antenna type is Printed antenna with 1.36dBi gain. 2. Calculate SAR test exclusion thresholds from condition “1” formulas. 4. CONCLUSION Since Source-base time average power is below SAR test exclusion power thresholds, the SAR evaluation is n…

Text truncated - open the document above for the full version.

Report No.: RF130705D03 1 of 33 Report Format Version 5.2.0 FCC TEST REPORT REPORT NO.: RF130705D03 MODEL NO.: Lenovo N700 FCC ID: EMJMN700 RECEIVED: Jul. 5, 2013 TESTED: Jul. 13 ~ 19, 2013 ISSUED: Jul. 22, 2013 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130705D03 2 of 33 Report Format Version 5.2.0 Table of Contents RELEASE CONTROL RECORD ................................................................................. 4 1. CERTIFICATION ............................................................................................... 5 2. SUMMARY OF TEST RESULTS ...................................................................... 6 2.1 MEASUREMENT UNCERTAINTY .................................................................... 6 3. GENERAL INFORMATION ............................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ................................................................. 7 3.2 DESCRIPTION OF TEST MODES ................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................... 9 3.3 DUTY CYCLE OF TEST SIGNAL ................................................................... 11 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................... 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................. 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................. 13 4. TEST TYPES AND RESULTS ........................................................................ 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ......................... 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ........................................................................................... 14 4.1.2 TEST INSTRUMENTS .................................................................................... 15 4.1.3 TEST PROCEDURES .................................................................................... 16 4.1.4 DEVIATION FROM TEST STANDARD ........................................................... 16 4.1.5 TEST SETUP .................................................................................................. 17 4.1.6 EUT OPERATING CONDITIONS ................................................................... 17 4.1.7 TEST RESULTS ............................................................................................. 18 4.2 CONDUCTED EMISSION MEASUREMENT .................................................. 22 4.3 6DB BANDWIDTH MEASUREMENT ............................................................. 22 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT ........................................... 22 4.3.2 TEST SETUP .................................................................................................. 22 4.3.3 TEST INSTRUMENTS .................................................................................... 22 4.3.4 TEST PROCEDURE ....................................................................................... 22 4.3.5 DEVIATION FROM TEST STANDARD ........................................................... 22 4.3.6 EUT OPERATING CONDITIONS ................................................................... 22 4.3.7 TEST RESULTS ............................................................................................. 23 4.4 CONDUCTED OUTPUT POWER ................................................................... 24 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT .................... 24 4.4.2 TEST SETUP .................................................................................................. 24 4.4.3 TEST INSTRUMENTS .................................................................................... 24 4.4.4 TEST PROCEDURES .................................................................................... 24 4.4.5 DEVIATION FROM TEST STANDARD ........................................................... 24 4.4.6 EUT OPERATING CONDITIONS ................................................................... 24 4.4.7 TEST RESULTS ............................................................................................. 25 4.5 POWER SPECTRAL DENSITY MEASUREMENT ......................................... 26 4.5.1 LIMITS OF POWER SPE…

Text truncated - open the document above for the full version.

Report No.: RF130705D03-1 1 of 21 Report Format Version 5.0.0 Reference No.: 130719D04 FCC TEST REPORT REPORT NO.: RF130705D03-1 MODEL NO.: Lenovo N700 FCC ID: EMJMN700 RECEIVED: Jul. 5, 2013 TESTED: Jul. 16, 2013 ISSUED: Jul. 22, 2013 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130705D03-1 2 of 21 Report Format Version 5.0.0 Reference No.: 130719D04 Table of Contents RELEASE CONTROL RECORD ................................................................................. 3 1. CERTIFICATION ............................................................................................... 4 2. SUMMARY OF TEST RESULTS ...................................................................... 5 2.1 MEASUREMENT UNCERTAINTY .................................................................... 5 3. GENERAL INFORMATION ............................................................................... 6 3.1 GENERAL DESCRIPTION OF EUT ................................................................. 6 3.2 DESCRIPTION OF TEST MODES ................................................................... 7 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................... 8 3.3 DESCRIPTION OF SUPPORT UNITS ............................................................. 9 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................... 9 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................. 10 4. TEST TYPES AND RESULTS ......................................................................... 11 4.1 CONDUCTED EMISSION MEASUREMENT ................................................... 11 4.2 RADIATED EMISSION AND BAND EDGE MEASUREMENT ......................... 11 4.2.1 LIMITS OF RADIATED EMISSION AND BAND EDGE MEASUREMENT ....... 11 4.2.2 TEST INSTRUMENTS .................................................................................... 12 4.2.3 TEST PROCEDURES .................................................................................... 13 4.2.4 DEVIATION FROM TEST STANDARD ........................................................... 13 4.2.5 TEST SETUP .................................................................................................. 14 4.2.6 EUT OPERATING CONDITIONS ................................................................... 14 4.2.7 TEST RESULTS ............................................................................................. 15 5. PHOTOGRAPHS OF THE TEST CONFIGURATION ..................................... 19 6. INFORMATION ON THE TESTING LABORATORIES .................................... 20 7. APPENDIX A – MODIFICATION RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ........................................................... 21 Report No.: RF130705D03-1 3 of 21 Report Format Version 5.0.0 Reference No.: 130719D04 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF130705D03-1 Original release Jul. 22, 2013 Report No.: RF130705D03-1 4 of 21 Report Format Version 5.0.0 Reference No.: 130719D04 1. CERTIFICATION PRODUCT: Lenovo dual mode Wireless touch mouse N700 BRAND: Lenovo MODEL NO.: Lenovo N700 APPLICANT: PRIMAX ELECTRONICS LTD. TESTED: Jul. 16, 2013 TEST SAMPLE: MASS-PRODUCTION STANDARDS: FCC Part 15, Subpart C (Section 15.249) ANSI C63.10-2009 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Jul. 22, 2013 ( Albee Chu / Specialist ) APPROVED BY : , DATE:Jul. 22, 2013 ( Ken Liu / Senior Manager ) Report No.: RF130705D03-1 5 of 21 Report Format Version 5.0.0 Reference No.: 130719D04 2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C (Section 15.249) STANDARD PARAGRAPH TEST TYPE RESULTREMARK 15.207 Conducted Emission Test N/A Power supply is 3Vdc from batteries 15.209 15.249 15.249 (d) Radiated Emission Test Band Edge Measurement Limit: 50dB less than the peak value of fundamental frequency or meet radiated emission limit in s…

Text truncated - open the document above for the full version.

1 of 1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST

1 of 1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST