EMJR-TX100USONY Savanna Remote Control

１ 2 3 127.9 51.8 18.8 77.3g １ 2 3 127.9 51.8 18.8 77.3g １ 2 3 127.9 51.8 18.8 77.3g 127.9 51.8 18.8 １ 2 3 77.3g Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Radiation Exposure Statement: The product comply with the US/Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: 1) le dispositif ne doit pas produire de brouillage préjudiciable, et2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirabl Radiation Exposure Statement The product comply with the US/Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available." Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. 低功率電波輻射性電機管理辦法 第十二條 經型式認証合格之低功率射頻電機，非經許可，公司、商號或 使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信﹔ 經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機 設備之干擾。 La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estaçães do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. 당해 무선설비는 운용중 전파혼신 가능성이 있음 해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음.

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Declaration letter Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Declaration letter for label requirement Date: 2014-10-16 FCC ID: EMJR-TX100U The label is permanent affixed in the battery compartment, and the EUT will be selling to market without the battery installed. The users can see the label during the battery installation process. The battery cover can be opened without any special tools. Please don’t hesitate to contact us, if you have any question(s). Thank you! ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: 2014-09-16 FCC ID: EMJR-TX100U AUTHORIZATION LETTER To whom it may concern: We, the undersigned, hereby authorize Amanda Wu / Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu / Senior Specialist of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: August 28, 2014 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: EMJR-TX100U Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: 2014-09-22 FCC ID: EMJR-TX100U To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 2015/2/28 in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT

7. 不使用 SS-00259 中禁止的物質和用途. 8.Product must be halogen free FCC LABEL 2D-71101SE01 Cheery.Qiao 14-06-18 印刷顏色:黑底白字. 6. 80#合成紙+霧膜 *58.2mm * 1 9 . 2 m m SN: YYYY MM 000001 (SN,000001~999999,十進制) (月代碼 ,01~12) (年代碼, 2014,2015......) Made In China SONY Savanna Remote Control Model: RMF-TX100U SN: YYYYMM000001 FCC ID: EMJR-TX100U IFETE: xxxxxxxxxxxxx Subtel: 00000 IC: 4251A-TX100U CNC: A-0000 Rating: 3V 40mA  Label loctation Inside of EUT

Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9

FCC ID: EMJR-TX100U Report No.: RF140828D01 Operational Description The device is operates in the 2.4GHz frequency spectrum with throughput of 1Mbps which DTS technique will be applied. The transmitter of the EUT is powered by 3.0Vdc from batteries. The antenna is Metal PIFA antenna. The other instruction, please have a look at the users manual.

Report No.: SA140828D01 1 of 6 Report Format Version 5.0.1 RF EXPOSURE REPORT REPORT NO.: SA140828D01 MODEL NO.: RMF-TX100U FCC ID: EMJR-TX100U RECEIVED: Aug. 28, 2014 TESTED: Aug. 28 ~ Sep. 3, 2014 ISSUED: Sep. 10, 2014 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA140828D01 2 of 6 Report Format Version 5.0.1 Table of Contents RELEASE CONTROL RECORD................................................................................. 3 1. CERTIFICATION .............................................................................................. 4 2. EVALUATION RESULT .................................................................................... 5 3. SAR TEST EXCLUSION THRESHOLDS ......................................................... 6 4. CONCLUSION ................................................................................................. 6 Report No.: SA140828D01 3 of 6 Report Format Version 5.0.1 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140828D01 Original release Sep. 10, 2014 Report No.: SA140828D01 4 of 6 Report Format Version 5.0.1 1. CERTIFICATION PRODUCT: SONY Savanna Remote Control BRAND NAME: SONY MODEL NO.: RMF-TX100U APPLICANT: PRIMAX ELECTRONICS LTD. TESTED: Aug. 28 ~ Sep. 3, 2014 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) KDB 447498 D03 IEEE C95.1 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Sep. 10, 2014 ( Jessica Cheng / Senior Specialist ) APPROVED BY : , DATE: Sep. 10, 2014 ( Rex Lai / Assistant Manager ) Report No.: SA140828D01 5 of 6 Report Format Version 5.0.1 2. EVALUATION RESULT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where ÿ f(GHz) is the RF channel transmit frequency in GHz . ÿPower and di stance are rounded to the nearest mW and mm before calculation. ÿThe result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA140828D01 6 of 6 Report Format Version 5.0.1 3. SAR TEST EXCLUSION THRESHOLDS Maximum measured transmitter power: Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 10-g extremity SAR test exclusion thresholds Result 2.402 ~ 2.480 1.2 5 0.372 7.5 Pass NOTE: 1. The antenna type is Metal PIFA Antenna with 3.28dBi gain. 2. Calculate SAR test exclusion thresholds from condition “1” formulas. 4. CONCLUSION Since Source-base time average power is below SAR test exclusion power thresholds, the SAR evaluation is not required.

Report No.: RF140828D01 1 of 33 Report Format Version 5.2.1 FCC TEST REPORT REPORT NO.: RF140828D01 MODEL NO.: RMF-TX100U FCC ID: EMJR-TX100U RECEIVED: Aug. 28, 2014 TESTED: Aug. 28 ~ Sep. 3, 2014 ISSUED: Sep. 10, 2014 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140828D01 2 of 33 Report Format Version 5.2.1 Table of Contents RELEASE CONTROL RECORD............................................................................. 4 1. CERTIFICATION .......................................................................................... 5 2. SUMMARY OF TEST RESULTS .................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ............................................................... 6 3. GENERAL INFORMATION .......................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................. 7 3.2 DESCRIPTION OF TEST MODES ............................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............... 9 3.3 DUTY CYCLE OF TEST SIGNAL............................................................... 11 3.4 DESCRIPTION OF SUPPORT UNITS ....................................................... 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ........................................ 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................ 13 4. TEST TYPES AND RESULTS .................................................................... 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ..................... 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT...................................................................................... 14 4.1.2 TEST INSTRUMENTS ............................................................................... 15 4.1.3 TEST PROCEDURES ................................................................................ 16 4.1.4 DEVIATION FROM TEST STANDARD ...................................................... 16 4.1.5 TEST SETUP ............................................................................................. 17 4.1.6 EUT OPERATING CONDITIONS ............................................................... 17 4.1.7 TEST RESULTS ......................................................................................... 18 4.2 CONDUCTED EMISSION MEASUREMENT ............................................. 22 4.3 6DB BANDWIDTH MEASUREMENT ......................................................... 22 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT ...................................... 22 4.3.2 TEST SETUP ............................................................................................. 22 4.3.3 TEST INSTRUMENTS ............................................................................... 22 4.3.4 TEST PROCEDURE .................................................................................. 22 4.3.5 DEVIATION FROM TEST STANDARD ...................................................... 22 4.3.6 EUT OPERATING CONDITIONS ............................................................... 22 4.3.7 TEST RESULTS ......................................................................................... 23 4.4 CONDUCTED OUTPUT POWER .............................................................. 24 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT ............... 24 4.4.2 TEST SETUP ............................................................................................. 24 4.4.3 TEST INSTRUMENTS ............................................................................... 24 4.4.4 TEST PROCEDURES ................................................................................ 24 4.4.5 DEVIATION FROM TEST STANDARD ...................................................... 24 4.4.6 EUT OPERATING CONDITIONS ............................................................... 24 4.4.7 TEST RESULTS ......................................................................................... 25 4.5 POWER SPECTRAL DENSITY MEASUREMENT ..................................... 26 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT .................. 26 4.5.2 TEST SETUP ............................................................................................. 26 4.5.3 T…

Text truncated - open the document above for the full version.

1 of 1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST