EMJTWSU202C1HP Pocket Playlist

Product: HP 90W Power A dap ter with USB Char ger Fol d 1: 4-p anel accordion Fol d 2: 4-panel accordion 6620 Cypresswood Drive Suite 120 Spring, TX 77379 832.717.4331 Document: Q SP Par t number: 679668-B21 Col or Side 1: Black Flat size: 17 x 27 in. Col or Side 2: Black Finished size: 4.25 x 6.75 in. The information con tained herein is subject to change without notice. The only warran tie s f or HP products and services are set for th in the express warran ty sta tements accompanying such products and services. Nothing herein should be construed as constituting an additional warran ty. HP shall not be liable for technical and editorial errors or omissions con tained herein. © Copyright 2012 Hewlett-P ackard Development Company, L.P . First Edition: November 2012 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limithatts for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup HP Pocket Playlist Quick Setup 699915-B21 English Hardware components Accessory/strap holder USB cable connector Reset button Power light Wireless light Power button Connection source Wi-Fi Protected Setup (WPS) button 1 Connect the HP Pocket Playlist to an external power source. 2 Turn on the HP Pocket Playlist. NOTE: Press and hold po wer button for 3 seconds. 3 Instal l the software on your computer. This icon will appear on your desk top f or easy access when you wan t to l aunch the application. 4 Go to the Application Store on your mobile device, and search for the H…

Text truncated - open the document above for the full version.

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Declaration for no non‐US channel operation December 12, 2012 We, PRIMAX ELECTRONICS LTD. declare that the device does not support any non-US channels in all the operational mode(s) for the following product. FCC ID: EMJTWSU202C1 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Date: December 10, 2012 Federal Communications Commission Authorization and Evaluation Division Subject: Short‐term confidentiality request regarding application for certification of FCC ID: EMJTWSU202C1 Pursuant to DA 04‐1705 of the Commission’s public notice, we request short‐term confidential treatment for the following information until January 23, 2013 in order to ensure sensitive business information remains confidential until the actual marketing of the device. External Photos Te st setup photos User’s Manual Internal Photos Sincerely yours, ------------------------------------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

No. 669, Ruey Kuang Road Neihu Taipei, Taiwan, R.O.C. Tel: 883-2-2798-9008 Fax: 886-2-8798-1565 Power of Attorney Date: November 29, 2012 T o whom it may concern: We, the undersigned PRIMAX ELECTRONICS LTD. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan Branch on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, -------------------------------------- C.T. Huang Compliance Dept. / Director Phone: 886-2-2798-9008 ext.1710 Fax: 886-2-8797-1565 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

Product of China SN:CCSYWWZZZZ REV 1.0A LABEL(3*20MM) Print on the back side of Doc Ock: HP Pocket Playlist HP :SKUNoH4D65AA SpresPNa :708330-001 RegulatoryModel:WSU202C1 FCC ID:EMJTWSU202C1 IC:4251A-TWSU202C1 CAN ICES-3(B) / NMB--3(B) Rating: +5.0V ,0.5A max (Graphics 2012Nov19) BACK font:Airal size:5.5pt 3mm XXXX HP,HQ-TRE,71004 Boeblingen,gemany AA-00/000 APPROVED

Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9

FCC ID: EMJTWSU202C1 Report No.: RF 121101D25 Operational Description This device is a HP Pocket Playlist, which operates in 2.4GHz band; the maximum data rate could be up to 150Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 150Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 3.7Vdc from battery and 5Vdc from host equipment or adapter or car charger. The antenna is chip antenna without antenna connector. For more detailed instruction, please take a look at the user’s manual.

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 20 Report No. : SA121101D25 Issued Date : Dec. 10, 2012 Revision : R01 FCC SAR Test Report Report No. : SA121101D25 Applicant : PRIMAX ELECTRONICS LTD. Address : No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. Product : HP Pocket Playlist FCC ID : EMJTWSU202C1 Brand : HP Model No. : WSU202C1 Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1991 / IEEE 1528:2003 FCC OET Bulletin 65 Supplement C (Edition 01-01) KDB 248227 D01 v01r02 / KDB 447498 D01 v04 / KDB 941225 D07 v01 Date of Testing : Dec. 05, 2012 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch - Taiwan HwaYa Lab, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Evonne Liu / Specialist Approved By : Roy Wu / Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 20 Report No. : SA121101D25 Issued Date : Dec. 10, 2012 Revision : R01 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ................................................................................................................ 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 12 3.4 SAR Measurement Procedure ................................................................................................................................... 13 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 13 3.4.2 Volume Scan Procedure................................................................................................................................... 13 3.4.3 Power Drift Monitoring ...................................................................................................................................... 13 3.4.4 Spatial Peak SAR Evaluation ........................................................................................................................... 14 3.4.5 SAR Averaged Methods ........................................…

Text truncated - open the document above for the full version.

Report No.: RF121101D25 1 of 55 Report Format Version 5.0.0 FCC TEST REPORT REPORT NO.: RF121101D25 MODEL NO.: WSU202C1 FCC ID: EMJTWSU202C1 RECEIVED: Nov. 1, 2012 TESTED: Nov. 8 ~ 20, 2012 ISSUED: Nov. 29, 2012 APPLICANT: PRIMAX ELECTRONICS LTD. ADDRESS: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF121101D25 2 of 55 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD..............................................................................4 1. CERTIFICATION .....................................................................................5 2. SUMMARY OF TEST RESULTS .............................................................6 2.1 MEASUREMENT UNCERTAINTY ..........................................................6 3. GENERAL INFORMATION .....................................................................7 3.1 GENERAL DESCRIPTION OF EUT........................................................7 3.2 DESCRIPTION OF TEST MODES..........................................................9 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........10 3.1 DUTY CYCLE OF TEST SIGNAL .........................................................13 3.2 DESCRIPTION OF SUPPORT UNITS ..................................................15 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................15 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................16 4. TEST TYPES AND RESULTS ...............................................................17 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................17 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ..................................................................................................17 4.1.2 TEST INSTRUMENTS ..........................................................................18 4.1.3 TEST PROCEDURES ...........................................................................19 4.1.4 DEVIATION FROM TEST STANDARD .................................................19 4.1.5 TEST SETUP ........................................................................................20 4.1.6 EUT OPERATING CONDITIONS ..........................................................20 4.1.7 TEST RESULTS ....................................................................................21 4.2 CONDUCTED EMISSION MEASUREMENT ........................................34 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .....................34 4.2.2 TEST INSTRUMENTS ..........................................................................34 4.2.3 TEST PROCEDURES ...........................................................................35 4.2.4 DEVIATION FROM TEST STANDARD .................................................35 4.2.5 TEST SETUP ........................................................................................35 4.2.6 EUT OPERATING CONDITIONS ..........................................................36 4.2.7 TEST RESULTS ....................................................................................37 4.3 6DB BANDWIDTH MEASUREMENT ....................................................41 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT .................................41 4.3.2 TEST SETUP ........................................................................................41 4.3.3 TEST INSTRUMENTS ..........................................................................41 4.3.4 TEST PROCEDURE .............................................................................41 4.3.5 DEVIATION FROM TEST STANDARD .................................................41 4.3.6 EUT OPERATING CONDITIONS ..........................................................41 4.3.7 TEST RESULTS ....................................................................................42 4.4 CONDUCTED OUTPUT POWER .........................................................43 Report No.: RF121101D25 3 of 55 Report Format Version 5.0.0 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT ..........43 4.4.2 TEST SETUP ........................................................................................43 4.4.3 TEST INSTRUMENTS ..........................................................................43 4.4.4 TEST PROCEDURES ...........................................................................43 4.4.5 DEVIATION FROM TEST STANDARD ...................…

Text truncated - open the document above for the full version.

1 of 3 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST-MODE A 2 of 3 CONDUCTED EMISSION TEST-MODE B 3 of 3 RADIATED EMISSION TEST

FCC SAR Test Report Report Format Version 5.0.0 Issued Date : Dec. 10, 2012 Report No. : SA121101D25 Revision : R01 Appendix D. Photographs of EUT and Setup FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA121101D25 Revision : R01 <Photographs of EUT> <Photographs of SAR Setup> Front Face of EUT with 0.5 cm Gap Rear Face of EUT with 0.5 cm Gap Left Side with 0.5 cm Gap Top Side with 0.5 cm Gap