EROGLSLDLBATAmbient Light Sensor, Dual Loop

GLS-LDL-EX-BATT Battery-Powered Photo Sensor with inNET EX ® , Dual-Loop Installation & Operation Guide Description The Crestron ® GLS-LDL-EX-BATT is a battery-powered, wireless photo sensor designed for daylight harvesting applications to control the balance of natural and articial lighting in an indoor space. Dual-loop sensing is achieved on the GLS-LDL-EX-BATT by two internal photocells—one for open-loop daylight sensing and one for closed-loop ambient light sensing. Installation NOTES: Observe the following points: • This product must be installed and used in accordance with appropriate electrical codes and regulations. • This product must be installed by a qualied electrician. • Sensors must be mounted on a vibration-free surface. The GLS-LDL-EX-BATT must be installed so that it faces a window. The device should be installed approximately 4 to 6 feet (1.22 to 1.83 meters) away from the window. The optimum viewing angle for the open loop sensor is 35 ̊. The closed-loop viewing angle is straight down. Additional Resources Visit the product page on the Crestron website (www.crestron.com) for additional information and the latest rmware updates. Arrow must point toward window. Holes for mounting screws. The base must be mounted to the drywall or drop ceiling using the provided anchors. 1. Determine the proper orientation for the GLS-LDL-EX-BATT. 2. Hold the base on the mounting surface, and use the holes for the mounting screws to mark the screw locations. 3. Using a 1/4 in drill bit, drill a pilot hole for the small anchor, and insert the small anchor into the pilot hole. 4. Using a #2 or #3 Phillips screwdriver, push the self-tapping anchor into the surface of the drywall until the cutting blades penetrate the surface. Using gentle forward pressure, rotate the anchor until the collar sets ush to the surface of the ceiling. 5. Secure the base to the mounting surface using two screws. 6. Place the sensor on the base and then rotate the sensor clockwise to secure it. The sensor has the capability to rotate up to 40º along the base after it is mounted. Rotate the sensor so that it is perpendicular to the window. Mount the Base When mounting the base, ensure that the arrow on the base, shown below, points toward the desired window. 35° Insert the Batteries Insert the batteries into the back of the GLS-LDL-EX-BATT. The orientation of the batteries is indicated on the device. Conguration The GLS-LDL-EX-BATT is set up and congured during system commissioning. Refer to the SIMPL Windows help le for details. Replace the Batteries The battery should be replaced with a battery that is the same or better than the provided Energizer ® L92 Ultimate Litium AAA battery. Discard batteries appropiately after use. As of the date of manufacture, the GLS-LDL-EX-BATT has been tested and found to comply with specications for CE marking. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help Industry Canada (IC) Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. RF ID It is recommended to have direct access to the GLS-LDL-EX-BATT and to use Crestron Toolbox™ to set the RF ID of the device. Set the RF ID for the GLS-LDL-EX-BATT by doing the following. 1. Wake the device by pressing the button on the GLS-LDL-EX-BATT. 2. Set the RF ID of the device using Crestron Toolbox. The RF ID must match the RF ID specied in the Crestron Studio or SIMPL Windows program. 3. Press the button on the GLS-LDL-EX-BATT to ensure that the device is still awake and the RF ID is transferred to the device. The RF ID can also be set by putting the device into Setup mode. 1. Press the button for more than 4 seconds. The LEDs blink. 2. Set the RF ID using Crestron Toolbox. Setup mode exits after 5 minutes. Firmware Upgrade NOTE: Before using the GLS-LDL-EX-BATT, ensure the device is usin…

Text truncated - open the document above for the full version.

Front Top Back

FCC/IC label

REVISIONS NAMEREVDESCRIPTIONDATEAPPROVED JH A ORIGINAL ISSUE PER EWO20492/18/15 22 LINK DRIVE, ROCKLEIGH, N.J. 07647 (201) 750-7004 FAX (201) 767-5772 NAME DATE DRAWN BY CHECKED FINISHED GDS DESIGNED BY SIZE PRINT NUMBER REV LABEL, BARCODE, 6507060 APX: 1.625 X 0.375, 200948.FMT A275772 UNLESS OTHERWISE SPECIFIED: ALL DIMENSIONS ARE IN INCHES TOLERANCES ARE: FRACTIONS 1/64 ANGLES ½ DECIMALS .XX .01 .XXX .005 THIS DRAWING IS THE EXCLUSIVE PROPERTY OF CRESTRON ELECTRONICS, INC. DISCLOSURE OR REPRODUCTION IN WHOLE OR IN PART, WITHOUT PRIOR WRITTEN PERMISSION, IS PROHIBITED EXCEPT FOR THE MANUFACTURE OF ARTICLES FOR CRESTRON. USED ON SORT NAME 1:1 APPROVED JS6/17/15 DEBURR & BREAK ALL SHARP EDGES JH2/18/15 JH2/18/15 6507060 GLS-LDL-EX-BATT SCALE: 275772-A.CDR FILE: SHEET 1 OF 1 A ALL PARTS & PROCESSES MUST BE RoHS COMPLIANT 0.375 R .063 1.625 PN 6507060 GLS-LDL-EX-BATT ASM IN COO NOTES: 1. MATERIAL: UL/CSA APPROVED GLOSS COATED SILVER POLYESTER, .002” THK WITH PERMANENT ACRYLIC ADHESIVE. 2. PRINT: TEXT AND GRAPHICS - BLACK. 3. USE COMPUTER FILE 200948-A.FMT FOR THE ACTUAL PRODUCTION OF THE LABEL. 4. ASM IN COO: TO BE CHANGED TO COUNTRY OF ORIGIN PRODUCT IS ASSEMBLED IN. (EX. USA, CANADA, ETC...) M/N: GLS-LDL-EX-BATT FCC ID: EROGLSLDLBAT IC: 5683C-GLSLDLBAT MANUAL SEE

FDD ID: EROGLSLDLBAT IC: 5683C-GLSLDLBAT FCC Registration #412871 Industry Canada Site #5683C-1 VCCI#3551 Page 2 of 26 Table of Contents 1. REFERENCE STANDARDS .............................................................................................. 3 1.1 T EST FACILITY ............................................................................................................................. 3 2. SYSTEM TEST CONFIGURATION ................................................................................. 4 2.1 P RODUCT DESCRIPTION ............................................................................................................... 4 2.2 B LOCK DIAGRAM ......................................................................................................................... 4 2.3 EUT SETUP JUSTIFICATION ......................................................................................................... 5 2.4 EUT EXERCISE SOFTWARE AND MODE(S) OF OPERATION ......................................................... 5 2.5 C ABLES ........................................................................................................................................ 5 2.6 S PECIAL ACCESSORIES ................................................................................................................ 5 2.7 S UPPORT EQUIPMENT ................................................................................................................... 6 2.8 E QUIPMENT MODIFICATION ........................................................................................................ 6 2.9 T EST EQUIPMENT ......................................................................................................................... 7 3. TEST RESULTS ................................................................................................................... 8 3.1 C OMPLIANCE STATEMENT ........................................................................................................... 8 3.2 A NTENNA REQUIREMENTS .......................................................................................................... 9 3.3 99% BANDWIDTH ...................................................................................................................... 10 3.4 F UNDAMENTAL FIELD STRENGTH ............................................................................................. 12 3.5 R ADIATED SPURIOUS EMISSIONS .............................................................................................. 16 3.6 T RANSMITTER AC POWER LINE CONDUCTED EMISSIONS ......................................................... 19 3.7 DUTY CYCLE CORRECTION FACTOR (DCCF) ........................................................................... 20 This document shall not be reproduced, except in full, without written approval from Crestron Electronics, Inc. Revision History Revision Description Date 00 Initial release 06-25-2015 FDD ID: EROGLSLDLBAT IC: 5683C-GLSLDLBAT FCC Registration #412871 Industry Canada Site #5683C-1 VCCI#3551 Page 3 of 26 1. Reference Standards Measurements were performed according to the following procedures and standards: 1) ANSI C63.4: 2014 2) Industry Canada RSS-Gen Issue 4 3) Industry Canada RSS-210 Issue 8 4) Industry Canada ICES-003 Issue 5 All measurements were performed in a 3-meter semi-anechoic chamber and the control room. 1.1 Test Facility The 3-meter semi-anechoic chamber used to collect conducted and radiated emission data is located at 22 Link Drive, Rockleigh, New Jersey. This test facility has been placed on file with the FCC, Registration Number: 412871, and Industry Canada, Site Number: 5683C- 1. FDD ID: EROGLSLDLBAT IC: 5683C-GLSLDLBAT FCC Registration #412871 Industry Canada Site #5683C-1 VCCI#3551 Page 4 of 26 2. System Test Configuration 2.1 Product Description The equipment under test (EUT) is a Crestron Ambient Light Sensor, Dual Loop, model: GLS- LDL-EX-BATT manufactured by Crestron Electronics, Inc. Model Number: GLS-LDL-EX-BATT 2.2 Block Diagram PW‐2420 RU 120VAC Network Under Floor Outside Chamber MC3 GLS-LDL-EX-BATT (EUT) FDD ID: EROGLSLDLBAT IC: 5683C-GLSLDLBAT FCC Registration #412871 Industry Canada Site #5683C-1 VCCI#3551 Page 5 of 26 2.3 EUT Setup Justification The system was configured for testing in a representative user configuration with nominal interface data activity and typical loading. Fresh batteries were used for testing. 2.4 EUT Exercise Software and Mode(s) of Operation The EUT was configured to transmit continuously. Channel 11 (2405 MHz) Channel 18 (2440 MHz) Channel 26 (2480 MHz) Power setting used during testing 8. 2.5 Cables EUT has no cables. 2.6 Special Accessories There are no special accessories for compliance of this EUT. FDD ID: EROGLSLDLBAT IC: 5683C-GLSLDLBAT FCC Registration #412871 Industry Canada Site #5683C-1 VCCI#3551 Page 6 of 26 2.7 Support equipment No Description Manufacturer Model No Serial No 1 POWER SUPPLY CRESTRON PW-2420RU N/A 1 CONTROL SYASTEM CRESTRON MC3 N/A 2.8 Equipment Modification There were no modifications installed during compliance measurements. FDD ID: EROGLSLDLBAT IC: 5683C-GLSLDLBAT FCC Registration #412871 Industry Canada Site #5683C-1 VCCI#3551 Page 7 of 26 2.9 Test Equipment Equipment Type Frequency Range Manufacturer Model No. Serial No. Cal. Date Cal. Due Date R&S EMI Receiver 20 Hz – 40 GHz ROHDE & SCHWARZ ESU40 100076 10/23/2014 10/23/2016 Teseq Bilog Antenna 30 MHz – 2 GHz Teseq CBL 6112D 25231 12/16/2014 12/16/2016 ETS-Lindgren Double Ridge Horn Antenna 1 GHz – 18 GHz ETS 3117 00047560 12/1/2014 12/1/2016 R&S Preamplifier 1GHz – 18 GHz ROHDE & SCHWARZ TS-PR18 100044 12/18/2013 12/18/2015 ETS-Lindgren Standard Gain Horn Antenna 18 GHz – 26.5 GHz ETS 3160-09 00078911 12/3/2014 12/3/2016 R&S Preamplifier 18 GHz – 26.5 GHz ROHDE & SCHWARZ TS-PR26 100030 12/18/2013 12/18/2015 All instruments are calibrated in accordance with the manufacturer’s recommendations. All antennas are …

Text truncated - open the document above for the full version.

EUT ceiling mount position EUT wall mount position EUT wall mount position