EROZUMLINK-KPZUM Keypad

ZUMLINK-KP- Zūm® Wired Keypad with Link Communication, Rocker Button Getting Started Scan the QR code to view the Quick Start Guide. REMARQUE IMPORTANTE: Pour être conforme aux exigences de conformité d’ISED CANADA et de la FCC en matière d’exposition aux radiofréquences, l’antenne utilisée pour cet émetteur doit être installée de manière à assurer une distance de séparation d’au moins 20 cm de toutes les personnes. toute autre antenne ou émetteur. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: www.crestron.com/docs/8886 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.   For additional information on the Crestron® ZUMLINK-KP-R, visit www.crestron.com/model/6511187  Regulatory Model: M201937001  Please note that any modifications to the device software or configuration, including but not limited to the init file(s), can cause device performance to vary beyond the scope of the currently referenced FCC authorization. Accordingly, if any user modifications are sought to be made to the device software or conf iguration, the user may be required to independently seek fresh FCC and other regulatory authorizations as relevant prior to IMPORTANT NOTE: To comply with ISED CANADA and FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter. distributing or marketing the devices or products inc orporating the same. Industry Canada (IC) Compliance Statement CAN ICES-3 (B)/NMB-3(B) This product is Listed to applicable UL® Standards and requirements tested by Underwriters Laboratories Inc. Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc. ©2020 Crestron Electronics, Inc. This device contains licence-exempt transmitter (s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2. L’app areil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Legal The product warranty can be found at www.crestron.com/warranty. The specific patents that cover Crestron products are listed atwww.crestron.com/legal/patents. Certain Crestron products contain open source software. For specific information, visit www.crestron.com/opensource. Crestron, the Crestron logo, and Zūm are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of UL LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not respo nsible for errors in typography or photography. Crestron Electronics, Inc. 15 Volvo Drive, Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7656 www.crestron.com Product Information - Doc. 8639A (2055226) 10/07/20 ZUMLINK-KP Zūm® Wired Keypad with Link Communication, Rocker Button, White Additional button configurations Four-button keypad: Two buttons for on and off control and two scene recall buttons  ZUMLINK-BTN4 (Pad Printed)  ZUMLINK-BTN4 ENGRAVED Six-button keypad: Two buttons for on and off control, two buttons for dimming up and down, and two scene recall buttons  ZUMLINK-BTN6 (Pad Printed)  ZUMLINK-BTN6 ENGRAVED Eight-button keypad: Four buttons for on and off control and four buttons for dimming up and down  ZUMLINK-BTN8 (Pad Printed)  ZUMLINK-BTN8 ENGRAVED Single-rocker button (included): Simple on and off lighting control ZUMLINK-BTNR ENGRAVED The Crestron® ZUMLINK-KP keypad provides control of one or more Zūm® wired load controllers (sold separately) via CBL-CAT5E-ZUMLINK-P cables (sold sepa…

Text truncated - open the document above for the full version.

SCS-F018: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 7.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Website: https://www.cps.bureauveritas.com/ Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (obsolete) 4.0 5.0 Sep-16-2014 Updated company name & logo (current) 5.0 6.0 Jun-27-2018 Updated References and Contact info 6.0 7.0 Aug-30-202 SCS-F018: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 7.0 March 03, 2021 To: BVCPS, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, Crestron Electronics Inc hereby authorize Bureau Veritas Consumer Product Services, Inc. to act as a Certification Body for certifying for the following project(s): FCC ID: EROZUMLINK-KP Product Description: ZUM Keypad Model: ZUMLINK-KPPR We affirm that between Bureau Veritas Consumer Product Services, Inc. and Crestron Electronics Inc, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, William Wack Client’s signature Client’s name / title Lead Compliance Engineer Contact information / Crestron Electronics, Inc. 22 Link Drive, Rockleigh, New Jersey, 07647

SCS-F019: Confidentiality Request Letter Page 1 of 2 Rev 7.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Website: https://www.cps.bureauveritas.com/ Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (obsolete) 2.0 3.0 Jan-31-2012 Added IC confidentiality letter form (obsolete) 3.0 4.0 March-26-2015 Corrections to STC form. Added reference to KDB (obsolete) 4.0 5.0 Nov-19-2015 Updated company logo (current) 5.0 6.0 Jun-26-2019 Updated References and Contact Info 6.0 7.0 Aug-30-2020 SCS-F019: Confidentiality Request Letter Page 2 of 2 Rev 7.0 March 03 2021 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046-1609 Cc: Bureau Veritas Consumer Products Services Inc. 775 Montague Expressway Milpitas, CA 95035 Subject: Confidentiality Request for FCC ID: EROZUMLINK-KP Pursuant to CFR 47 sections 0.457 and 0.459, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application be held confidential: Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagram Short Term External Photos Short Term Permanent i Internal Photos Short Term Permanent Operational Description/ Theory of Operation Short Term Permanent Parts List Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent i User’s Manual The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: To avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 or 180 days; or for a specified date of not to exceed 180 days from the Grant Date The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, William Wack Client’s signature Client’s name / title Lead Compliance Engineer Contact information / Crestron Electronics, Inc. 22 Link Drive, Rockleigh, New Jersey, 07647 i Permanent confidentiality may be requested in accordance with FCC KDB 726920

EUT Photo-External view EUT – Front View EUT – Rear View EUT – Bottom View EUT – Top View EUT – Left View EUT – Right View

NOTES: 1. MA TERIAL: UL/CSA APPROVED GLOSS COATED SIL VER POLYESTER, .002” THK WITH PERMANENT A CRYLIC ADHESIVE. 2. PRINT : TEXT AND GRAPHICS - BLACK. 3. USE COMPUTER FILE 4531128-278860- C.NLSN FOR THE A CTUAL PRODUCTION OF THE LABEL. 4. ASSEMBLED IN COO : TO BE CHANGED TO THE COUNTR Y THAT THE PRODUCT IS ASSEMBLED IN. (EX . USA, CANADA, ETC...) R 0.125" 1.000" 1.000" PN 6511187 REV 01 SN XXXXXXXXXXXX MODEL: M201937001 SKU: ZUMLINK-KP-R-W ASM IN COO 4FL8 Energy Management Equipment FCC ID: EROZUMLINK-KP IC: 5683C-ZUMLINKKP

Report No.: FCC_RF_SL20061501-CRE-008_1M_MPE Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: FCC_RF_SL20061501-CRE-008_1M_MPE FCC ID: EROZUMLINK-KP Test Model: M201937001 Series Model: N/A Received Date: 12/07/2020 Test Date: 12/16/2020 - 06/22/2021 Issued Date: 07/01/2021 Applicant: Crestron Electronics, Inc. Address: 15 Volvo DrRockleigh, NJ 07647, USA Manufacturer: Crestron Electronics, Inc. Address: 15 Volvo DrRockleigh, NJ 07647, USA Issued By: Bureau Veritas Consumer Products Services, Inc. Lab Address: 775 Montague Expressway, Milpitas, CA 95035 Test Location (1): 775 Montague Expressway, Milpitas, CA 95035 FCC Registration / Designation Number: 540430 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by A2LA or any government agencies. Report No.: FCC_RF_SL20061501-CRE-008_1M_MPE Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 2.4 Antenna Gain ...................................................................................................................................... 5 2.5 Calculation Result of Maximum Conducted Power ............................................................................. 6 3 Conclusion ............................................................................................................................................ 6 Report No.: FCC_RF_SL20061501-CRE-008_1M_MPE Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued FCC_RF_SL20061501-CRE-008_1M_MPE Orignal Release 07/01/2021 Report No.: FCC_RF_SL20061501-CRE-008_1M_MPE Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: ZUM Keypad Brand: Crestron Electronics Test Model: M201937001 Series Model: N/A Sample Status: Engineering sample Applicant: Crestron Electronics, Inc Test Date: 12/16/2020 - 06/22/2021 Standards: FCC Part 2 (Section 2.1093) KDB 447498 D01 General RF Exposure Guidance v06 IEEE C95.1-1992 The above equipment has been tested by Bureau Veritas Consumer Products Services, Inc., Milpitas Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: 07/01/2021 Ellen Chu / Test Engineer Approved by : , Date: 07/01/2021 Deon Dai / Engineer Reviewer Report No.: FCC_RF_SL20061501-CRE-008_1M_MPE Page No. 5 / 6 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 Antenna Gain The antenna type is Chip antenna with -2 dBi gain. Report No.: FCC_RF_SL20061501-CRE-008_1M_MPE Page No. 6 / 6 Report Format Version: 6.1.1 2.5 Calculation Result of Maximum Conducted Power Mode Max Power (dBm) Max Power (mW) Turn-Up Tolerance Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) BT_LE_1M -0.34 0.92 ±…

Text truncated - open the document above for the full version.

Report No.: FCC_IC_RF_SL20061501-CRE-008_BLE_1M Page No. 1 / 37 Report Format Version: 6.1.1 FCC IC Test Report Report No.: FCC_IC_RF_SL20061501-CRE-008_BLE_1M FCC ID: EROZUMLINK-KP IC: 5683C-ZUMLINK-KP Test Model: M201937001 Received Date: 12/07/2020 Test Date: 12/16/2020 - 06/22/2021 Issued Date: 06/29/2021 Applicant: Crestron Electronics, Inc. Address: 15 Volvo DrRockleigh, NJ 07647, USA Manufacturer: Crestron Electronics, Inc. Address: 15 Volvo DrRockleigh, NJ 07647, USA Issued By: Bureau Veritas Consumer Products Services, Inc. Lab Address: 775 Montague Expressway, Milpitas, CA 95035 Test Location (1): 775 Montague Expressway, Milpitas, CA 95035 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by A2LA or any government agencies. Report No.: FCC_IC_RF_SL20061501-CRE-008_BLE_1M Page No. 2 / 37 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 9 3.3 Duty Cycle of Test Signal .................................................................................................................. 10 3.4 Description of Support Units .............................................................................................................. 11 3.4.1 Configuration of System under Test ................................................................................................... 11 3.5 General Description of Applied Standards ......................................................................................... 11 4 Test Types and Results ...................................................................................................................... 12 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 12 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 12 4.1.2 Test Instruments ................................................................................................................................ 13 4.1.3 Test Procedures ................................................................................................................................. 14 4.1.4 Deviation from Test Standard ............................................................................................................ 14 4.1.5 Test Setup .......................................................................................................................................... 15 4.1.6 EUT Operating Conditions ................................................................................................................. 16 4.1.7 Test Results ....................................................................................................................................... 17 4.2 Conducted Emission Measurement .................................................................................................. 23 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 23 4.2.2 Test Procedures ................................................................................................................................. 23 4.2.3 Deviation from Test Standard ............................................................................................................ 23 4.2.4 Test Setup .........…

Text truncated - open the document above for the full version.

Radiated Emission Test Below 1GHz Front View Radiated Emission Test Below 1GHz Rear View Radiated Emission Test Above 1GHz Front View Radiated Emission Test Above 1GHz Rear View