EZSDEI7641Security/Remote Control Transmitter

Model 1400XPL Owner's Guide G562PL_07-06.qxd 7/26/06 5:33 PM Page 1 i © 2006 Directed Electronics—all rights reserved Limited Lifetime Consumer Warranty Directed Electronics promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed Electronics unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following con- ditions are met: the unit was professionally installed and serviced by an authorized Directed Electronics dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed Electronics dealer; and the unit is returned to Directed Electronics, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, tele- phone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identifica- tion number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-trans- ferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installa- tion or removal of the unit. Directed Electronics, in its sole discretion, will determine what constitutes excessive damage and may refuse the return of any unit with exces- sive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WAR- RANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED ELECTRONICS NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED ELECTRONICS DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHO- RIZED DEALERS OR INSTALLERS. DIRECTED ELECTRONICS SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED ELECTRONICS IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDAL- ISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND G562PL_07-06.qxd 7/26/06 5:33 PM Page i ii © 2006 Directed Electronics—all rights reserved HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REIN- STALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED ELECTRONICS OR ITS SUB- SIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED ELECTRONICS SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED ELECTRONICS DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED ELEC- TRONICS SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow lim- itations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. This product may be covered by a Guaranteed Protection Plan ("GPP"). See your authorized Directed Electronics dealer for details of the plan or call Directed Electronics Customer Service at 1-800-876-0800. Directed Electronics security systems, including this unit, are deterrents against possible theft. Directed Electronics is not offering a guarantee or insurance against vandalism, damage or theft of the automo- bile, its parts or contents; and hereby expressly disclaims any liability whatsoever, including without limitation, liability for theft, damage and/or vandalism. Directed Electronics does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this security system. Make sure you have all of the following information from your dealer: A clear copy of the sales receipt, showing the following: ■Date of purchase ■Your full name and address ■Authorized dealer's company name and address ■Type of alarm installed ■Year, make, model and color of the automobile ■Automobile license number ■Vehicle identification number ■All security options installed on automobile ■Installation receipts G562PL_07-06.qxd 7/26/06 5:33 PM Page ii 1 © 2006 Directed Electronics—all rights reserved Table of Contents Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . i Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 What is I…

Text truncated - open the document above for the full version.

Thursday, July 27, 2006 Chief, Equipment Approval Services Federal Communications Commission P.O. Box 358315 Pittsburgh, PA 15251-5315 Re: Request of Confidentiality Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying as outlined below: Schematics Block diagram Operational description Parts List All the above for EZSDEI7641 The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application. Sincerely, Minas Minassian RF Engineering Manager

Thursday, July 27, 2006 TUV Product Services 10040 Mesa Rim Road San Diego, CA 92121 RE: FCC ID EZSDEI7641 Dear Sir or Madam: The following is the SAR calculation for the EUT filed under EZSDEI7641 using the system’s maximum RF emissions. The calculation is based on FCC 47CFR Part 2 and OET 65. Per OET 65: Maximum permissible exposure is the Freq. (MHz) ÷ 1500 = MPE/cm² 914.750MHz (lowest used freq.) ÷ 1500 = 0.6098mW/cm² The following equations determine the distance from the antenna that the power density is ≤ 0.6098mW/cm². +20.00dBm Transmitter Power (Max) 0dBi Antenna Gain (Max) +20.00dBm + 0dBi = +21.00dBm EIRP +20.00dBm EIRP = 100mW EIRP 0.6098mW/cm² = 100mW ÷ (4 x π x r²) r = SQR(100 ÷ 4 x π x 0.6098) r = 3.61cm We would like to emphasize that this device is a hand held remote control for vehicle security and convenience systems. The typical use is for unlocking/locking door locks, activating a car alarm or remote starting the vehicle. We estimate that the typical user will activate the remote about 20 times for a period of 2 seconds on average in a 24 hour period. Therefore, the exposure risk to the user is further minimized by the very low duty cycle of on time of the device. In addition, the following statement will be added to our installation/operation manual: To satisfy FCC RF exposure compliance requirements, this device should be used in hand-held, hand- operated configurations only. The device and its antenna must maintain a separation distance of 20cm or more from a person’s body, except for the hand and wrists, to satisfy RF exposure compliance. This device is designed to be used in a person’s hands and its operating configurations do not support normal transmissions while it is carried in pockets or holsters next tot a person’s body. Sincerely, Minas Minassian RF Engineering Manager

Report No. SC602954-08 Page 1 of 36 Rev.No 1.0 TÜV AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 858 678 1400 FAX 858 546 0364 MEASUREMENT AND TECHNICAL REPORT DIRECTED ELECTRONICS INCORPORATED 1 Viper Way Vista, CA 92083 DATE: 26 July 2006 This Report Concerns: Original Grant: X Class II Change: Equipment Type: 7601 V/P/X Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes: Defer until: No: X Company Name agrees to notify the Commission by: N/A of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes: No: X* (*) FCC Part 15, Paragraph(s) 15.247(a); 15.247(b); 15.247(c); 15.247(d); 15.207(a) and 15.209(a) (*) Canadian Standard(s) RSS-Gen 7.2 and RSS-210, Annexes 7 and 8 (*) FCC 15.35; ANSI C63.4 Report Prepared by: TÜV AMERICA, INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone: 858 678 1400 Fax: 858 546 0364 Report No. SC602954-08 Page 2 of 36 Rev.No 1.0 TÜV AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 858 678 1400 FAX 858 546 0364 TABLE OF CONTENTS Pages 1.0 GENERAL INFORMATION 3 - 8 1.1 Product Description 3 - 6 1.2 Related Submittal Grant 6 1.3 Tested System Details 6 1.4 Test Methodology 7 1.5 Test Facility 8 2.0 SYSTEM TEST CONFIGURATION 9 2.1 Justification 9 2.2 EUT Exercise Software 9 2.3 Special Accessories 9 2.4 Equipment Modifications 9 2.5 Configuration of Test System 9 3.0 BANDWIDTH EQUIPMENT/DATA PEAK OUTPUT POWER EQUIPMENT/DATA RF CONDUCTED EMISSIONS EQUIPMENT/DATA RADIATED SPURIOUS EMISSIONS EQUIPMENT/DATA BANDEDGE EQUIPMENT/DATA PULSE DUTY CYCLE CORRECTION FACTOR DATA 4.0 ATTESTATION STATEMENT 41 Report No. SC602954-08 Page 3 of 36 Rev.No 1.0 TÜV AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 858 678 1400 FAX 858 546 0364 1.0 GENERAL INFORMATION 1.1 Product Description Company: Directed Electronics, Inc. Address: 1 Viper Way ` Vista, CA 92081 Contact: Minas Minassian Position: RF Engineer Phone: (760) 598-6200 Fax: (760) 598-6400 E-mail Address: [email protected] General Equipment Description EUT Description: Hand held keyfob transceiver for car alarm and convenience systems. EUT Name: Venom SST HHU Model No.: 7641V, 7641P, 7641X Serial No.: N/A Product Options: N/A Configurations to be tested: 1 EUT Specifications and Requirements Length : 3.10" Width: 1.42" Height: 0.63" Weight: N/A Power Requirements Voltage: 6V (2 x CR2025) # of Phases: N/A Other Special Requirements: N/A Typical Installation and/or Operating Environment: EUT Power Cable: Not Applicable Report No. SC602954-08 EUT Interface Ports and Cables Interface Shielding Type Type Termination Connector Type Port Termination None EUT Software: N/A EUT Operating Modes to be Tested 1. Continuous modulated transmission 2. The System is a digital modulation design under FCC part 15.247 EUT System Components Description Model # Serial # FCC ID # Keyfob 7641V, 7641P, 7641X N/A EZSDEI7641 Oscillator Frequencies Frequency Derived Frequency Component # / Location Description of Use 14.75806452 MHz 915MHz Transmitter RF carrier Power Supply: N/A Power Line Filters: N/A Critical EMI Components (Capacitors, ferrites, etc.) : N/A System Configuration Block Diagram - No connections or setup, just the self contained keyfob. Page 4 of 36 Rev.No 1.0 TÜV AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 858 678 1400 FAX 858 546 0364 Report No. SC602954-08 Page 5 of 36 Rev.No 1.0 TÜV AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 858 678 1400 FAX 858 546 0364 1.2 Related Submittal Grant None 1.3 Tested System Details The FCC ID’s for all equipment, plus descriptions of all cables used in the tested system are: None Report No. SC602954-08 Page 6 of 36 Rev.No 1.0 TÜV AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 858 678 1400 FAX 858 546 0364 1.4 Test Methodology Purpose of Test: To demonstrate compliance with the following tests. TEST SUMMARY Test Description Paragraph Number Pass/Fail (P/F) Bandwidth 15.247(a)(2) RSS 210, Annex 8, A8.2 Pass 603 kHz Peak Output Power 15.247(b) RSS 210, Annex 8, A8.4 Pass 0.10325 W Directional Gain antennas > 6 dBi 15.247(b)(3) N/A RF Conducted Emissions 15.247(c) RSS 210, Annex 8, A8.5 Pass Radiated Spurious Emissions – Restricted Bands (1GHz to 25GHz) 15.247(c); RSS 210, Annex 8, A8.5 Pass with DC Peak Power Spectral Density 15.247(d); RSS 210, Annex 8, A8.2 Pass Bandedge 15.247(c) RSS 210, Annex 7, A7.3 Pass Processing Gain 15.247(e) N/A Conducted Emissions 15.207(a); RSS-Gen 7.2.2 N/A Radiated Emissions 15.209(a); RSS-Gen 7.2 Pass - No emissions detected between 30-1000 MHz Pulse Duty Cycle Correction Factor FCC 15.35(c); ANSI C63.4:2003, Clause 13.1.4.2 Pass Testing was performed according to the procedures in FCC/ANSI C63.4 and CSA 108.8-M1983. Report No. SC602954-08 Page 7 of 36 Rev.No 1.0 TÜV AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 858 678 1400 FAX 858 546 0364 1.5 Test Facility The open area test site and conducted measurement data were tested by: TÜV AMERICA, INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone: 858 678 1400 Fax: 858 546 0364 The Test Site Data and performance comply with ANSI C63.4 and are registered with the FCC, 7435 Oakland Mills Road, Columbia Maryland 21046. All Measurement Data is acquired according to the content of FCC Measurement Procedure and ANSI C63.4, unless supplemented with additional requirements as noted in the test report. Report No. SC602954-08 Page 8 of 36 Rev.No 1.0 TÜV AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 858 678 1400 FAX 858 546 0364 2.0 SYSTEM TEST CONFIGURATION 2.1 Justification The EUT was initially tested for FCC emissions in the following configuration: See Test Setup Photos Exhibit 2.2 EUT Exercise Software None 2.3 Special Accessories None 2.4 Equipment Modifications None 2.5 Configuration of Test System See Test Setup Photos Exhibit Report No. SC602954-08 Page 9 of 36 Rev.No 1.0 TÜV AMERICA INC 1004…

Text truncated - open the document above for the full version.