EZSDEI7856Two way transceiver SST car remote starter

  

  

© 2013 Directed. All Rights Reserved GOBRS3520 2013-07 Orbit OBRS-3520BKR 2-Way LED Remote User Guide Thank you for purchasing this Orbit Remote Transmitter. This guide provides a general description of operations for Orbit Remote Start and Security Systems. LOCK: Locks the DOORS and arms the STARTER KILL (if installed). UNLOCK: Unlocks the DOORS and disarms the STARTER KILL (if installed). Activates the AUX 1 output if Priority Door Access is configured. TRUNK: Opens the TRUNK or activates the AUX 3 output. Note: Trunk option must be installed. START: Remote starts or stops the engine. Gets the system into Cold Weather mode by pressing the AUX button and then pressing and holding the START/STOP button for 3 seconds. Orbit: This button serves as a second function button. This button allows assigning different functions to any of the other four buttons. Remote Pairing Procedure Confirmations 1. Press and hold “Orbit” button until the remote generates a long beep. The Lock and trunk LEDs illuminate for a period of 30seconds. 2. Turn the key to IGN ON 3. Press release and then press and hold the antenna programming button until the LED start flashing rapidly. The Parking lights will stay ON for 20 seconds. From this point, the installer has 20 seconds to complete steps 4-5. 4. Turn the key to IGN OFF/ON/OFF. The parking light should turn OFF. 5. Press and release lock button. The remote will play a melody and the parking lights will start flashing to confirm successful learning of the remote. FAILED PAIRING: The remote will play an error tone. In this case, press and release the programming button on the antenna, press “Orbit” to exit remote’s pairing mode and then repeat the whole process from STEP1. 6. Press “Orbit” button once OR leave the remote inactive for 30 seconds. Note: To learn the remote to a second car that has the same system, in STEP4, press the TRUNK button instead of the LOCK button. Government Regulations This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio / TV technician for help. To satisfy FCC RF exposure compliance requirements, this device should be used in hand-held, hand operated configurations only. The device and its antenna must maintain a separation distance of 20 cm or more from the person’s body, except for the hand and wrists, to satisfy RF exposure compliance. This device is designed to be used in a person’s hands and its operating configurations do not support normal transmissions while it is carried in pockets or holsters next to a person’s body. Canada Statements This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Les changements ou modifications non approuvés expressément par la partie responsable de la conformité pourrait annuler l'autorité de l'utilisateur à faire fonctionner l'équipement.

May 7, 2013 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification FCC ID: EZSDEI7856 Authority to Act as Agent On our behalf, I appoint Alan Laudani of Nemko USA Inc., 2210 Faraday Ave, STE 150, Carlsbad, CA, USA to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in Federal Communication Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko USA Inc, still resides with Minas Minassian, DEI Headquarters, Inc 1Viper way, Vista CA 92081, USA. This appointment is in effect until May 7, 2014. Sincerely, Minas Minassian Sr. director, hw/rf systems

May 7, 2013 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Re: Request of Confidentiality Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying as outlined below: Schematics Block diagram Operational description Parts List All the above for EZSDEI7856 The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application. Sincerely, Minas Minassian Sr. director, hw/rf systems

May 7, 2013 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification IC: 1513A-7856 FCC ID: EZSDEI7856 Models: 7856X 7856V OBRS-3520 Family letter This letter explains that Directed are using different models (Viper 7856V, Clifford 7856X and Autostart OBRS‐3520) on this product. All these models uses the same PCB, HW/RF and software, the only change is that the cases are cosmetically different. Sincerely, Minas Minassian Sr. director, hw/rf systems

U9 YARG LOOC DAPYEK REBBUR EDIS：gnitaoc ettaM+KCALB ROLOC NOCI：U5 yarG looC GNITNIRP：C624 SMP POOL LATEM：EMORHC ETTAM DAPYEK REBBUR POT：ETIHW TNECULSNART gnitaoc ettaM+GNITNIAP KCALB GNIVARGNE RESAL :AERA DEL ROLOC OGOL/NOCI：U5 yarG looC :GNISUOH MOTTOB/POT HCUOT TFOS KCALB TNIAP REBBUR )01011-TM , 0=EVAC(EROC EGNAHC GNIVARGNE：)52.0=EVAC C934 SMP 2 2 31'-2/1cirE ROLOC GNITNIRP .TOB YFIDOM LIAM-E 2/1 0020-472-008-1 V6587 :LEDOM 6587-A3151 :CI 6587IEDSZE :DI CCF 6102RC :YRETTAB .deificeps ton fi 2.0 eb lliw suoidaR .2 01011- TM sa emas si erutxeT .1 SBA/CP : LAIRETAM YDOB 01.0 02.0 04.0 80.0 03~6 003~021 021~03 EDARG NOISNEMID 6 REDNU 04.0 02.0 08.0 61.0 08.0 04.0 00.2 03.0 HSINIF LAIRETAM EDOC YB DPPA YB KHC TEEHSFO :TINU:ELACS YB NRD ETAD KETUN ELTIT EZIS NOITAROPROC ON GNIWARDTPEDVER SNOISIVER .VER.CCA NOITPIRCSED .NRD ETAD 1 LIAM 92/01 GNITNIRP OT GNIVARGNE cirE21'-92/01 1 3 LIAM-E 12/3 ROLOC GNITNIRP .TOB YFIDOM cirE31'-12/3 3

GNITAOC SSOLG /w KCALB C934 SMP LLEHS RETNEC：gnitaoc ettaM+KCALB ROLOC NOCI：U5 yarG looC :GNISUOH MOTTOB/POT TNIAP REBBUR HCUOT TFOS KCALB ROLOC OGOL：U5 yarG looC DAPYEK REBBUR POT：ETIHW TNECULSNART gnitaoc ettaM+GNITNIAP KCALB GNIVARGNE RESAL :AERA DEL ROLOC NOCI：U5 yarG looC GNITNIRP：C624 SMP U9 YARG LOOC LIAM 31'-12/3 2 31'-12/3cirE ROLOC GNITNIRP .TOB YFIDOM2 2 0020-472-008-1 X6587 :LEDOM 6587-A3151 :CI 6587IEDSZE :DI CCF 6102RC :YRETTAB 1 ETAD.NRD NOITPIRCSED .CCA.VER SNOISIVER VERTPEDON GNIWARD NOITAROPROC EZIS ELTIT KETUN ETAD YB NRD :ELACS:TINU FO TEEHS YB KHC YB DPPA EDOC LAIRETAM HSINIF 03.0 00.2 04.0 08.0 61.0 08.0 02.0 04.0 6 REDNU NOISNEMID EDARG 021~03 003~021 03~6 80.0 04.0 02.0 01.0 SBA/CP : LAIRETAM YDOB 01011-TM sa emas si erutxeT .1 .deificeps ton fi 2.0 eb lliw suoidaR .2 ROLOC GNITNIRP .TOB & N/P ESAC YFIDOM cirE21'-82/11 1 1

August 28, 2013 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification FCC ID: EZSDEI7856 Models: 7856X 7856V OBRS-3520 HHU LED Distance between antenna and hand user The distance from the user’s hand on the button on the remote and the antenna is 22mm. The user holds the remote from the keychain side, if not he will not see the LED display. 447498 D01 General 10 RF Exposure Guidance v05r01 4.3.1. Standalone SAR test exclusion considerations The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. LED Maximum peak output power --conducted:64mW Minimum Test Separation Distance:22mm Evaluation frequency:0.923GHz Square Root of Frequency in GHz:0.961 10-g Extremity test threshold:2.8< 7.5 1-g Body test threshold:2.8 < 3 Sincerely, Minas Minassian Sr. director, hw/rf systems

Nemko-CCL, Inc. 1940 West Alexander Street Salt Lake City, UT 84119 801-972-6146 Test Report Certification Test Of: 7856V, 7856X, & OBRS-3520 FCC ID: EZSDEI7856 Test Specification: FCC PART 15, Subpart C Test Report Serial No: 230381-10-2.2 Applicant: DEI Headquarters Inc. 1 Viper Way Vista, CA 92081 Dates of Test: May 29 - June 7, 2013 Report Issue Date: July 11, 2013 Accredited Testing Laboratory By: NVLAP Lab Code 100272-0 Nemko-CCL, Inc. TEST REPORT: 230381-10-2.2 REPORT ISSUE DATE: 07/11/2013 Page 2 of 46 CERTIFICATION OF ENGINEERING REPORT This report has been prepared by Nemko-CCL, Inc. to document compliance of the device described below with the requirements of Federal Communications Commission (FCC) Part 15, Subpart C. This report may be reproduced in full; partial reproduction may only be made with the written consent of the laboratory. The results in this report apply only to the sample tested. - Applicant: DEI Headquarters Inc. - Manufacturer: DEI Headquarters Inc. - Brand Name: DEI Headquarters Inc. - Model Numbers: 7856V, 7856X, & OBRS-3520 - FCC ID Number: EZSDEI7856 On this 11 th day of July 2013, I, individually and for Nemko-CCL, Inc., certify that the statements made in this engineering report are true, complete, and correct to the best of my knowledge, and are made in good faith. Although NVLAP has recognized that the Nemko-CCL, Inc. EMC testing facilities are in good standing, this report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. Nemko-CCL, Inc. Tested by: Mark M. Feil EMC Engineer Reviewed by: Thomas C. Jackson General Manager Nemko-CCL, Inc. TEST REPORT: 230381-10-2.2 REPORT ISSUE DATE: 07/11/2013 Page 3 of 46 TABLE OF CONTENTS PAGE SECTION 1.0 CLIENT INFORMATION .................................................................................4 SECTION 2.0 EQUIPMENT UNDER TEST (EUT) ..................................................................5 SECTION 3.0 TEST SPECIFICATION, METHODS & PROCEDURES .............................9 SECTION 4.0 OPERATION OF EUT DURING TESTING ..................................................14 SECTION 5.0 SUMMARY OF TEST RESULTS ...................................................................15 SECTION 6.0 MEASUREMENTS, EXAMINATIONS AND DERIVED RESULTS ..........16 APPENDIX 1 TEST PROCEDURES AND TEST EQUIPMENT ..........................................36 APPENDIX 2 PHOTOGRAPHS ................................................................................................39 APPENDIX 3 AVERAGE FACTOR CALCULATION ..........................................................46 Nemko-CCL, Inc. TEST REPORT: 230381-10-2.2 REPORT ISSUE DATE: 07/11/2013 Page 4 of 46 SECTION 1.0 CLIENT INFORMATION 1.1 Applicant: Company Name: DEI Headquarters Inc. 1 Viper Way Vista, CA 92081 Contact Name: Minas Minassian Title: Sr. Director, HW/RF Systems 1.2 Manufacturer: Company Name: DEI Headquarters Inc. 1 Viper Way Vista, CA 92081 Contact Name: Minas Minassian Title: Sr. Director, HW/RF Systems Nemko-CCL, Inc. TEST REPORT: 230381-10-2.2 REPORT ISSUE DATE: 07/11/2013 Page 5 of 46 SECTION 2.0 EQUIPMENT UNDER TEST (EUT) 2.1 Identification of EUT: Brand Name: DEI Headquarters Inc. Model Numbers: 7856V, 7856X, & OBRS-3520 Dimensions: 6.0 cm x 2.9 cm x 0.7 cm 2.2 Description of EUT: The 7856V was tested as a representative of models 7856V, 7856X and OBRS-3520. The differences in the models are cosmetic only. The 7856V, only, will be referred to throughout the remainder of this report. The 7856V is a handheld key fob, exercised by push buttons to arm/disarm, lock/unlock, start vehicle systems, etc. A continuous transmit mode was configured by the applicant for RF testing. The device is powered by a 3.7 V battery. The 7856V transceiver operates using 25 channels, spaced 620 KHz apart, in the 902 MHz to 928 MHz frequency band. The 7856V transceiver uses a helical antenna extending from a trace on the PCB. Testing was performed at the upper channel (923.835 MHz), the middle channel (916.395 MHz), and the lower channel (907.095 MHz). See the plots of the channels below. Nemko-CCL, Inc. TEST REPORT: 230381-10-2.2 REPORT ISSUE DATE: 07/11/2013 Page 6 of 46 Nemko-CCL, Inc. TEST REPORT: 230381-10-2.2 REPORT ISSUE DATE: 07/11/2013 Page 7 of 46 This report covers the circuitry of the devices subject to FCC Part 15, Subpart C. The circuitry of the device subject to FCC Part 15, Subpart B has been tested and found to comply. See Nemko-CCL report #230381-10-1.1. Nemko-CCL, Inc. TEST REPORT: 230381-10-2.2 REPORT ISSUE DATE: 07/11/2013 Page 8 of 46 2.3 EUT and Support Equipment: The EUT and support equipment used during the test are listed below: Brand Name Model Number Serial Number FCC ID Number or Compliance Description Name of Interface Ports / Interface Cables BN: DEI Headquarters Inc. MN: 7856V (Note 1) EZSDEI7856 Key fob remote None Note: (1) EUT The support equipment listed above was not modified in order to achieve compliance with this standard. 2.4 Modification Incorporated/Special Accessories on EUT: No modifications were made during testing to comply with the specification. Nemko-CCL, Inc. TEST REPORT: 230381-10-2.2 REPORT ISSUE DATE: 07/11/2013 Page 9 of 46 SECTION 3.0 TEST SPECIFICATION, METHODS & PROCEDURES 3.1 Test Specification: Title: FCC PART 15, Subpart C (47 CFR 15) 15.203 and 15.247 Limits and methods of measurement of radio interference characteristics of radio frequency devices Purpose of Test: The tests were performed to demonstrate initial compliance 3.2 Methods & Procedures: 3.2.1 §15.203 Antenna Requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufactur…

Text truncated - open the document above for the full version.

Accredited Testing Laboratory By: NVLAP Lab Code 100272-0 Nemko-CCL, Inc. 1940 West Alexander Street Salt Lake City, UT 84119 801-972-6146 Test Report Certification Test Of: 7856V, 7856X, & OBRS-3520 IC: 1513A-7856 Test Specifications: RSS-Gen Issue 3 (December 2010) RSS-210 Issue 8 (December 2010) Test Report Serial No: 230381-10-3.2 Applicant: DEI Headquarters Inc. 1 Viper Way Vista, CA 92081 Dates of Test: May 29 - June 7, 2013 Report Issue Date: July 11, 2013 Nemko-CCL, Inc. TEST REPORT: 230381-10-3.2 REPORT ISSUE DATE: 07/11/2013 Page 2 of 51 TRF-RSS210 Issue 2 May 2013 CERTIFICATION OF ENGINEERING REPORT This report has been prepared by Nemko-CCL, Inc. to document compliance of the device described below with the requirements of RSS-Gen Issue 3 (December 2010) and RSS- 210 Issue 8 (December 2010). This report may be reproduced in full. Partial reproduction may only be made with the written consent of the laboratory. The results in this report apply only to the sample tested. - Applicant: DEI Headquarters Inc. - Manufacturer: DEI Headquarters Inc. - Brand Name: DEI Headquarters Inc. - Model Number: 7856V, 7856X, & OBRS-3520 - IC: 1513A-7856 On this 11 th day July 2013, I, individually, and for Nemko-CCL, Inc., certify that the statements made in this engineering report are true, complete, and correct to the best of my knowledge, and are made in good faith. Although NVLAP has recognized that the Nemko-CCL, Inc. EMC testing facilities are in good standing, this report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. Nemko-CCL, Inc. Tested by: Mark M. Feil EMC Engineer Reviewed by: Thomas C. Jackson General Manager Nemko-CCL, Inc. TEST REPORT: 230381-10-3.2 REPORT ISSUE DATE: 07/11/2013 Page 3 of 51 TRF-RSS210 Issue 2 May 2013 TABLE OF CONTENTS PAGE SECTION 1.0 CLIENT INFORMATION .................................................................................4 SECTION 2.0 EQUIPMENT UNDER TEST (EUT)..................................................................5 SECTION 3.0 TEST SPECIFICATION, METHODS & PROCEDURES .............................9 SECTION 4.0 OPERATION OF EUT DURING TESTING..................................................16 SECTION 5.0 SUMMARY OF TEST RESULTS ...................................................................17 SECTION 6.0 MEASUREMENTS AND RESULTS ...............................................................18 APPENDIX 1 TEST PROCEDURES AND TEST EQUIPMENT .........................................41 APPENDIX 2 PHOTOGRAPHS ................................................................................................44 APPENDIX 3 AVERAGE FACTOR CALCULATION ..........................................................51 Nemko-CCL, Inc. TEST REPORT: 230381-10-3.2 REPORT ISSUE DATE: 07/11/2013 Page 4 of 51 TRF-RSS210 Issue 2 May 2013 SECTION 1.0 CLIENT INFORMATION 1.1 Applicant: Company Name: DEI Headquarters Inc. 1 Viper Way Vista, CA 92081 Contact Name: Minas Minassian Title: Sr. Director, HW/RF Systems 1.2 Manufacturer: Company Name: DEI Headquarters Inc. 1 Viper Way Vista, CA 92081 Contact Name: Minas Minassian Title: Sr. Director, HW/RF Systems Nemko-CCL, Inc. TEST REPORT: 230381-10-3.2 REPORT ISSUE DATE: 07/11/2013 Page 5 of 51 TRF-RSS210 Issue 2 May 2013 SECTION 2.0 EQUIPMENT UNDER TEST (EUT) 2.1 Identification of EUT: Brand Name: DEI Headquarters Inc. Model Number: 7856V, 7856X, & OBRS-3520 Dimensions: 6.0 cm x 2.9 cm x 0.7 cm 2.2 Description of EUT: The 7856V was tested as a representative of models 7856V, 7856X and OBRS-3520. The differences in the models are cosmetic only. The 7856V, only, will be referred to throughout the remainder of this report. The 7856V is a handheld key fob, exercised by push buttons to arm/disarm, lock/unlock, start vehicle systems, etc. A continuous transmit mode was configured by the applicant for RF testing. The device is powered by a 3.7 V battery. The 7856V transceiver operates using 25 channels, spaced 620 KHz apart, in the 902 MHz to 928 MHz frequency band. The 7856V transceiver uses a helical antenna extending from a trace on the PCB. Testing was performed at the upper channel (923.835 MHz), the middle channel (916.395 MHz), and the lower channel (907.095 MHz). See the plots of the channels below. Nemko-CCL, Inc. TEST REPORT: 230381-10-3.2 REPORT ISSUE DATE: 07/11/2013 Page 6 of 51 TRF-RSS210 Issue 2 May 2013 Nemko-CCL, Inc. TEST REPORT: 230381-10-3.2 REPORT ISSUE DATE: 07/11/2013 Page 7 of 51 TRF-RSS210 Issue 2 May 2013 Nemko-CCL, Inc. TEST REPORT: 230381-10-3.2 REPORT ISSUE DATE: 07/11/2013 Page 8 of 51 TRF-RSS210 Issue 2 May 2013 This report covers the circuitry of the devices subject to RSS-Gen and RSS-210. The circuitry of the device subject to ICES-003 has been tested to ICES-003 and found to comply. Compliance is shown in Nemko-CCL report #230381-10-1.1. 2.3 EUT and Support Equipment: The EUT and support equipment used during the test are listed below: Brand Name Model Number Serial Number IC ID Number or Compliance Description Name of Interface Ports / Interface Cables BN: DEI Headquarters Inc. MN: 7856V (Note 1) 1513A-7856 Key fob remote None Note: (1) EUT The support equipment listed above was not modified in order to achieve compliance with this standard. 2.4 Modification Incorporated/Special Accessories on EUT: No modifications were made during testing to comply with the specification. Nemko-CCL, Inc. TEST REPORT: 230381-10-3.2 REPORT ISSUE DATE: 07/11/2013 Page 9 of 51 TRF-RSS210 Issue 2 May 2013 SECTION 3.0 TEST SPECIFICATION, METHODS & PROCEDURES 3.1 Test Specification: Title: RSS-Gen Issue 3 (December 2010) RSS-210 Issue 8 (December 2010) Purpose of Test: The tests were performed to demonstrate initial compliance. 3.2 Requirements: 3.2.1 RSS-Gen 4.6.1 Occupied Bandwidth When an occupied bandwidth value is not specified in the applicable RSS, the transmitted signal bandwidth to be reported is to be its 99% emission ba…

Text truncated - open the document above for the full version.