GOH-PCMINI-4PAlarm Device

S t arting Y our V ehicle The remote control start function is activated by pressingthe START (key icon) button twice within 3 seconds onyour remote control transmitter. The system will checkcertain pre-conditions before starting, and if all safetyparameters are correct, the engine will start within 5seconds. If the vehicle’s starter cranks but does not startor starts and stalls, the remote engine start system willpower off then attempt to start the vehicle an additionalfour times.WARNING: TO AVOID DANGER OF CARBON MONOXIDE,NEVER REMOTE START A VEHICLE IN A CLOSED SPACESUCH AS A CLOSED GARAGE. T urning Y our V ehicle Off Press and hold the START (key icon) button again to turnthe vehicle off. If the vehicle is left running the remote startsystem will allow the vehicle to run for a total of 15 minutesand then automatically turn off. Entering the V ehicle While it is Running via Remote S t art 1. Unlock the vehicle doors using the factory keyless remote. If the vehicle’s doors are unlocked manuallyusing the key, the vehicle’s security system will triggerand the remote start system will turn off. Insertingthe ignition key into the ignition cylinder andturning it to the ON or RUN position will disarm thesecurity system. 2. Enter the vehicle. Do not press the brake pedal.3. Insert the key into the ignition and turn to the ON positi- ion. If the ignition key is accidently turned to the startposition, the system’s “starter anti-grind” feature willprevent the starter from re-cranking. 4. Press the brake pedal. The remote starter disenga- ges, the vehicle’s power window features are re-ena-bled and the vehicle will operate normally. Remote Start Activation 2 Times Remote Start Shutdown For 2 Seconds Press Press REMOTE START QUICK REFERENCE To engage the service mode , turn the ignition key to the ON or RUN position, depress and hold the brake pedal then, press andrelease the START (key icon) button on the remote controltransmitter three (3) times. The system will pause for one secondand then flash the parking lights three (3) times indicating that thesystem is in service mode. When attempting to activate the remotestart system while in service mode, the parking lights will flashthree (3) times and will not start.To disengage the service mode , turn the ignition key to the ON or RUN position, depress and hold the brake pedal, then press andrelease the START (key icon) button on the remote controltransmitter three (3) times. The system will pause for one secondand flash the parking lights one (1) time indicating that the systemhas exited service mode.Important Note: When taking your vehicle in for service, it is recommended that you inform the service personnel that yourvehicle is equipped with a remote start system.Remote Transmitter Programming Mode1. Open the driver’s door (the driver’s door must remain opened throughout the entire process). 2. Insert the ignition key into the vehicle’s ignition cylinder and turn to the ON or RUN position. 3. Locate the small black programming button behind the fusebox cover on the left side of the driver’s side lower dashboard. 4. Press and hold the black programming button for 10-15 seconds. The horn will honk and the parking lights will flash three times toindicate that the system has entered transmitter programmingmode. 5. Press and release the START (key icon) button on each trans- mitter. The horn will honk and the parking lights will flash onetime to indicate a successful transmitter learn each time theSTART (key icon) button is pressed. 6. To exit transmitter programming mode, turn the Ignition key to the OFF position, remove the ignition key from the ignition cyl-linder and test operation of the remote transmitter(s). Enabling / Disabling Confirmation Horn Honks1. Follow steps 1-4 in “Remote Transmitter Programming Mode” above. 2. Pressing the vehicle’s brake pedal will enable the confirmation horn honk feature. The vehicle’s horn will honk 1 time to indicatethat confirmation horn honks have been disabled and honk 2times to indicate that confirmation horn honks have been enabled. 3. To exit programming mode, turn the ignition key to the OFF pos- ition, remove the ignition key from the ignition cylinder and testoperation of the remote transmitter(s). See your owner’s manual for additional information on the remoteengine start system. This device complies with part 15 of the FCC rules.Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause unde sired operation. Per FCC 15.21, y ou are cautioned that changes or modifications not expressly approved by the part responsible for compliancecould void the user’s authority to operate the equipment.

123456 A B C D 654321 D C B A Title NumberRevisionSize B Date:18-Apr-2006Sheet of File:D:\My Documents\flora\FCCID\FCC1\FCC11\FCC11.DDBDrawn By: SW1 ENCODER IC1 OSC SAW+6V 433.920MHz 123456 A B C D 654321 D C B A Title NumberRevisionSize B Date:18-Apr-2006Sheet of File:D:\My Documents\flora\FCCID\FCC1\FCC11\FCC11.DDBDrawn By: SW1 ENCODER IC1 OSC SAW+6V 433.920MHz

Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 To whom it may concern: We, the undersigned, hereby authorize the Testing Division of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by CCS on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing CCS Testing Division as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

Compliance Certification Services Inc. Report No.: 60301204 Date of Issue: August 09, 2006 Page PHOTOGRAPHS OF EUT

FCC ID LABEL FORMAT AND LOCATION CODE SYSTEMS, INC. FCC ID: GOH-PCMINI-4P FCC ID: GOH-PCMINI-4P This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA

Compliance Certification Services Inc. Report No.: 60301204 Date of Issue: August 09, 2006 Page Compliance Certification Services Inc. Report No.: 60301204 Date of Issue: August 09, 2006 Page

Compliance Certification Services Inc. Report No.: 60301204-RP1 FCC ID: GOH-PCMINI-4P Date of Issue: August 09, 2006 Page 1 of 15 Rev. 00 FCC ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT CERTIFICATION TO FCC PART 15 REQUIREMENTS For INTENTIONAL RADIATOR of ALARM DEVICE FCC ID Number : GOH-PCMINI-4P Trade Name : CODE SYSTEMS, INC.; SUBARU Model Number : 1030838; 1031568 Agency Series : N/A Report Number : 60301204-RP1 Date : August 09, 2006 Issued to CODE SYSTEMS, INC. 525 Minnesota Drive Troy, Michigan 48083, USA Issued by Compliance Certification Services Inc. Hsintien Lab. No. 165, Chunghsen Road, Hsintien City Taipei Hsien, Taiwan TEL: (02) 2217-0894 FAX: (02) 2217-1029 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. Ltd. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Compliance Certification Services Inc. Report No.: 60301204-RP1 FCC ID: GOH-PCMINI-4P Date of Issue: August 09, 2006 Page 2 Rev. 00 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE........................................................ 3 2. PRODUCT DESCRIPTION........................................................................ 4 3. TEST FACILITY .......................................................................................... 4 4. MEASUREMENT STANDARDS ............................................................... 4 5. TEST METHODOLOGY ............................................................................ 4 6. MEASUREMENT EQUIPMENT USED ................................................... 5 7. POWERLINE RFI LIMIT .......................................................................... 5 8. RADIATED EMISSION LIMITS............................................................... 6 9. SYSTEM TEST CONFIGURATION ......................................................... 6 10. TEST PROCEDURE.................................................................................. 7 11. Equipment Modifications........................................................................... 8 12. TEST RESULT ........................................................................................... 9 12.1 Maximum Modulation Percentage (M%)................................................ 9 12.2 The Emissions Bandwidth......................................................................... 9 APPENDIX I ................................................................................................... 10 Compliance Certification Services Inc. Report No.: 60301204-RP1 FCC ID: GOH-PCMINI-4P Date of Issue: August 09, 2006 Page 3 Rev. 00 1. VERIFICATION OF COMPLIANCE COMPANY NAME : CODE SYSTEMS, INC. 525 Minnesota Drive Troy, Michigan 48083, USA CONTACT PERSON : MR. SHANE WILSON (RETAIL PROGRAM MANAGER) TELEPHONE NO. : 1-248-583-9620 EUT DESCRIPTION : ALARM DEVICE MODEL NAME/NUMBER : 1030838; 1031568 FCC ID : GOH-PCMINI-4P DATE TESTED : July 24, 2006 ~ July 26, 2006 REPORT NUMBER : 60301204-RP1 TYPE OF EQUIPMENT SECURITY EQUIPMENT (INTENTIONAL RADIATOR) EQUIPMENT TYPE 433.92 MHz ALARM DEVICE MEASUREMENT PROCEDURE ANSI 63.4 / 2003 LIMIT TYPE CERTIFICATION FCC RULE CFR 47, PART 15 The above equipment was tested by Compliance Certification Services Inc. for compliance with the requirements set forth in the FCC CFR 47, PART 15. The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Warning: This document reports conditions under which testing was conducted and results of tests performed. This document may not be altered or revised in any way unless done so by Compliance Certification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services Inc. will constitute fraud and shall nullify the document. Approved by: Reviewed by: Compliance Certification Services Inc. Report No.: 60301204-RP1 FCC ID: GOH-PCMINI-4P Date of Issue: August 09, 2006 Page 4 Rev. 00 2. PRODUCT DESCRIPTION Fundamental Frequency 433.92 MHz Power Source 6V Battery Transmitting Time Periodic < 5 seconds Associated Receiver Model: GOH-FRDPC2002 (FCC ID) Model Differences: Model Name Trade name Difference Tested (Checked) 1030838 CODE SYSTEMS, INC. Original 1031568 SUBARU For marketing purpose only. 3. TEST FACILITY The open area test sites and conducted measurement facilities used to collect the radiated data are located at No. 163-1, Chung Sheng Road, Hsin Tien City, Taipei, Taiwan R.O.C. The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 4. MEASUREMENT STANDARDS The site is constructed and calibrated in conformance with the requirements of ANSI C63.4/2003. 5. TEST METHODOLOGY For an intentional radiator, the spectrum shall be investigated from the lowest radio frequency signal generated in the device, without going below 9 KHz, up to at least the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. (CFR 47 Section 15.33) Compliance Certification Services Inc. Report No.: 60301204-RP1 FCC ID: GOH-PCMINI-4P Date of Issue: August 09, 2006 Page 5 Rev. 00 6. MEASUREMENT EQUIPMENT USED Open Area Test Site # K Name of Equipment Manufacturer Model Serial Number Calibration Due SITE NSA CCS K Site N/A 10/01/2006 MEASURE RECEIVER SCHAFFNER SCR3501 412 05/18/2007 SPECTRUM ANALYZER ADVANTEST R3132 120900029 No Calibration Required ANTENNA SCHAFFNER CBL 6112B 2846 05/26/2007 PRE- AMPLIFIER SCHAFFNER CPA9231A 3639 10/08/2006 CABLE SUHNER RG 214 N-TYPE #K2 02/17/2007 THERMO- HYGRO METER TFA N/A NO.4 02/08/2007 Above 1GHz Used EMC ANALYZER (100Hz-22GHz) HP 8566B 2937A06102 07/04/2007 ANTENNA (1-18GHz) EMCO 3115 00022256 01/12/2007 AMPLIFIER …

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.: 60301204-RP1 FCC ID: GOH-PCMINI-4P Date of Issue: August 09, 2006 Page 6 Rev. 00 8. RADIATED EMISSION LIMITS GENERAL REQUIREMENTS SECTION 15.209 RESTRICTED BANDS OF OPERATION SECTION 15.205 PERIODIC OPERATION IN THE BAND 40.66 -40.70 MHz AND ABOVE 70 MHz. SECTION 15.231 9. SYSTEM TEST CONFIGURATION Use a block of foam and combined it with EUT wrapping rubber band around it. This way it can test X, Y and Z axis. To activate continuous transmitting & receiving, place a small plastic block between rubber band and EUT push button. Radiated Open Site Test Set-up