GSSAV802G802.11g WLAN Mini PCI

8 8 0 0 2 2 . . 1 1 1 1 g g W W L L A A N N M M i i n n i i P P C C I I AV802G Quick Start Guide Version 1.0 1 No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from the copyright owner. All the other trademarks and registered trademarks are the property of their respective owners. Statement of Conditions We may make improvements or changes in the product described in this documentation at any time. The information regarding to the product in this manual are subject to change without notice. We assume no responsibility for errors contained herein or for direct, indirect, special, incidental, or consequential damages with the furnishing, performance, or use of this manual or equipment supplied with it, even if the suppliers have been advised of the possibility of such damages. Electronic Emission Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. FCC INFORMATION The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to overcome the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. The equipment is for home or office use. IMPORTANT NOTE FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the antenna and your body and must not be co-located or operating in conjunction with any other antenna or transmitter. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2 R&TTE Compliance Statement This equipment complies with all the requirements of the Directive 1999/5/EC of the European parliament and the council of 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity(R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC. As of April 8, 2000. Canada IC Compliance Statement Low Power License-Exempt Radio communication Devices (RSS-210) 1. Warning Note: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. 2. Operation in 2.4GHz band: To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Exposure of Humans to RF Fields for module built-in mobile Radios Equipment (RSS-102) 1. Mobile radios that are not body worn (e.g. mounted on vehicles or placed on desks, shelves, etc.) and operated such that humans are normally separated from their radiating element by at least 20 cm are not subject to SAR tests, but must have an RF evaluation by the certification applicant, based on the calculated or measured field strength value. SAR evaluation can be used if so desired in lieu of a RF evaluation of field strength limits. 2. Exposures produced by such radios shall not exceed the exposure limits specified in Health Canada's Safety Code 6. Health Canada’s address is :775 Brookfield Road, Ottawa, Ontario Canada K1A 1C1; Tel: (613) 954-6699 / Fax:(613) 941-1734 ; e-mail: [email protected]. T T a a b b l l e e o o f f C C o o n n t t e e n n t t s s INTRODUCTION ...........................................................................................................................................1 1.1 Features.................................................................................................................................. 1 1.2 System Requirements ............................................................................................................ 1 INSTALLATION .............................................................................................................................................2 2.1 Installation Procedures ........................................................................................................... 2 Confirm the Hardware Connection...........................................................................................................2 Installation Procedures.............................................................................................................................3 2.2 Installation Notes - Windows XP.............................................................................................5 2.3 Verifying a Successf…

Text truncated - open the document above for the full version.

8 8 0 0 2 2 . . 1 1 1 1 g g W W L L A A N N M M i i n n i i P P C C I I AV802G OEM installation guide STATEMENT FOR MODUAL APPROVAL This product is sold to OEM integrators only. The manual for the OEM integrators must include some instructions to be followed by the end users in the user manual. For example: The OEM integrators must be instructed to ensure that the end user has no manual instructions to remove or install the device. The OEM integrators must be instructed about the end product labeling ("Contains FCC ID:GSSAV802G, IC: 4280A-AV802G ") This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC and IC authorization is no longer considered valid and the FCC and IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and IC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example, access points, routers, wireless ADSL modems, wireless media adapter, wireless media gateway, and similar equipment). The final end product must be labeled in a visible area with the following: " Contains FCC ID:GSSAV802G, IC: 4280A-AV802G ". Manual Information for OEM integrator Following RF exposure info shall be supplied in end-users manual depends on the application. For mobile configuration of RF Exposure Information: IMPORTANT NOTE: To comply with FCC and IC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter

ViewSonic Corporation. 381 Brea Canyon Rd. Walnut, CA.91709 USA Attestation FCC ID GSSAV802G Product 802.11g WLAN Mini PCI Model AV802G Statements: Our company doesn’t provide U.S.A. people the software selection for U.S.A. to operate on channel 12 and 13 which are outside of the allowed U.S.A. frequency band for all future applications. Sincerely, Signature: 06.21,2004 (Name / Date)

ViewSonic Corporation 381 Brea Canyon Road, Walnut, California 91789 (909) 444-8888 * Fax (909) 444-8652 http://www.viewsonic.com Modular Approval Request Letter Date: June 15, 2004 FCC ID: GSSAV802G Dear Application Examiner, Viewsonic Corporation’s 802.11g WLAN Mini PCI (FCC ID:GSSAV802G) have your authorization as a limited modular approval specific to products below: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ADSL modems, wireless media adapter, wireless media gateway video capture and similar equipment). The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1.”The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2.“The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs; it is integrated in chip ISL3880IK. 3.”The modular transmitter must have its own power supply regulation”. The zero IF transceiver which will influence the frequency radiation, have to be 2.8V DC powered, so there are regulators in front of these chips; the part number of this regulator is ISL6411IR. The Mini PCI interface provide 3.3VDC.It’s can operation. 4.”The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C). “The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5.”The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a Mini PCI interface to test kit. Please sees section Photographs of Test Configuration in the test report, the EUT was plugged in this test kit. 6.”The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. ViewSonic Corporation 381 Brea Canyon Road, Walnut, California 91789 (909) 444-8888 * Fax (909) 444-8652 http://www.viewsonic.com 7.”The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. “The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are giver in the Users Manual. 8.”The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me of you have any further questions. Thanks for your attention. Best Regards, Sincerely Yours, ___________________________ June 15, 2004 James Huang Date QA & Regulatory Manager ViewSonic Corp Tel: 909-444-8786 e-Mail: [email protected]

ViewSonic Corporation 381 Brea Canyon Road, Walnut, California 91789 (909) 444-8888 * Fax (909) 444-8652 http://www.viewsonic.com June 15, 2004 Federal Communications Commission Authorization and Evaluation Division FCC ID: GSSAV802G Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: 1. Schematics 2. Operational Description 3. Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ___________________________ June 15, 2004 James Huang Date QA & Regulatory Manager ViewSonic Corp Tel: 909-444-8786 e-Mail: [email protected]

Company : ViewSonic Corporation. Page : 1 of 5 Product : 802.11g WLAN Mini PCI Model : AV802G Company : ViewSonic Corporation. Page : 2 of 5 Product : 802.11g WLAN Mini PCI Model : AV802G Company : ViewSonic Corporation. Page : 3 of 5 Product : 802.11g WLAN Mini PCI Model : AV802G Company : ViewSonic Corporation. Page : 4 of 5 Product : 802.11g WLAN Mini PCI Model : AV802G Company : ViewSonic Corporation. Page : 5 of 5 Product : 802.11g WLAN Mini PCI Model : AV802G

Company : ViewSonic Corporation. Model : AV802G Product : 802.11g WLAN Mini PCI 802.11g WLAN Mini PCI Model No: AV802G FCC IDGSSAV802G This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference and [2] this device must accept any interference received, including interference that may cause undesired operation. S/N Made in Taiwan

Company : ViewSonic Corporation. Page : 1 of 4 Product : 802.11g WLAN Mini PCI Model : AV802G Company : ViewSonic Corporation. Page : 2 of 4 Product : 802.11g WLAN Mini PCI Model : AV802G Company : ViewSonic Corporation. Page : 3 of 4 Product : 802.11g WLAN Mini PCI Model : AV802G Company : ViewSonic Corporation. Page : 4 of 4 Product : 802.11g WLAN Mini PCI Model : AV802G

Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：GSSAV802G Report No.：ER04-06-034FRF Page 1 of 92 TEST REPORT Product Name ： 802.11g WLAN Mini PCI Model Number ： AV802G Brand Name ： ViewSonic FCC ID ： GSSAV802G Applicant ： ViewSonic Corporation. Address ： 381 Brea Canyon Rd. Walnut, CA.91709 USA Received Date ： June 18, 2004 Tested Date ： July 29, 2003; June 10 ~ 24, 2004 Notes： 1. This report will be invalid if duplicated or photocopied in part. 2. This report refers only to the specimen(s) submitted to testing, and be invalid as seperately used. 3. This report is invalid without examination stamp and signature of this institute. 4. The tested specimen(s) will be preserved for thirty days from the data issued. 5. The report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. 6. This report is modified from ER03-07-064. Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：GSSAV802G Report No.：ER04-06-034FRF Page 2 of 92 Test Report Certification Product Name ： 802.11g WLAN Mini PCI Model Number ： AV802G Brand Name ： ViewSonic FCC ID ： GSSAV802G Applicant ： ViewSonic Corporation. Measurement Standard : FCC 47 C.F.R. Part 15, Subpart B and Subpart C (2003) ANSI C63.4 (2001) WE HEREBY CERTIFY THAT: The measurements shown in the attachment were made in accordance with the procedures indicated, and the energy emitted by the equipment was found to be within the limits applicable. We assume full responsibility for the accuracy and completeness of these measurements and vouch for the qualifications of all persons taking them. Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：GSSAV802G Report No.：ER04-06-034FRF Page 3 of 92 TABLE OF CONTENTS TITLE PAGE NO. 1. GENERAL INFORMATION..................................................................................................................5 1.1 General Statement .................................................................................................................................5 1.2 General Description of EUT & Power ..................................................................................................5 1.3 Description of Peripherals.....................................................................................................................6 1.4 EUT & Peripherals Setup Diagram.......................................................................................................7 1.5 EUT Operating Condition.....................................................................................................................7 1.6 Description of Laboratory.....................................................................................................................8 1.7 Summary of Test Results ......................................................................................................................8 2. CONDUCTED POWERLINE TEST .....................................................................................................9 2.1 Test Equipments ...................................................................................................................................9 2.2 Test Setup .............................................................................................................................................9 2.3 Conducted Power Line Emission Limit ................................................................................................10 2.4 Test Procedure ......................................................................................................................................10 2.5 Uncertainty of Conducted Emission .....................................................................................................10 2.6 Conducted Power Line Emission..........................................................................................................11 2.7 Photos of Conduction Test....................................................................................................................12 3. RADIATED EMISSION TEST...............................................................................................................13 3.1 Test Equipments ...................................................................................................................................13 3.2 Test Setup .............................................................................................................................................13 3.3 Radiation Limit .....................................................................................................................................14 3.4 Test Procedures.....................................................................................................................................15 3.5 Uncertainty of Radiated Emission ........................................................................................................15 3.6 Radiated Rf Noise Measurement ..........................................................................................................16-67 3.7 Photos of Open Site ..............................................................................................................................57-71 4. 6dB BANDWIDTH MEASUREMENT..................................................................................................57 4.1 Test Equipments ...................................................................................................................................57 4.2 Test Setup ..............................................................…

Text truncated - open the document above for the full version.

Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：GSSAV802G Report No.：ER04-06-034FRF Page 12 of 62 2.7 Photos of Conduction Test Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：GSSAV802G Report No.：ER04-06-034FRF Page 42 of 62 3.7 Photos of Open Site Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：GSSAV802G Report No.：ER04-06-034FRF Page 43 of 62