GT3FC008Transceiver module

859 FC User Manual 5-5 Togoshi 6 Chome, Shinagawa-Ku, Tokyo 142-8511 Japan ZigBee ® RF4CE compatible RF module with a built-in 2.4GHz band antenna Brand: SMK Product Name: Transceiver Module Model number: RXX9000-15XX GENERAL This “ZigBee RF4CE compatible RF module with a built-in 2.4GHz band antenna” which uses the platform of recently established ZigBee RF4CE responds to such requirements. The communication system is based on 2.4GHz band IEEE 802.15.4 PHY/MAC system and is capable of N-to-N high reliability two-way communication, low power consumption, coexisting with other 2.4GHz band RF and security settings. This product, featuring a two-way communication by the use of radio frequencies and network function, contributes to the realization of a more convenient and stylish remote controls. With regards to the technical development of RF remote controls, this “ZigBee RF4CE compatible RF module” is an addition to the previously developed FX8000, with more product lineup coming up for the expansion of the remote control business. Features 1) By using the omni-directionality feature of RF, PAN with remote control as its core can be easily structured (N-to-N application is possible). 2). Compatible with ZigBee RF4CE Specification Version 1.00. 3). The standby-mode and intermittent reception feature conserves electricity consumption. 4). DSSS employed for modulation system provides high-resistance to noise and interference. 5). The employment of radio communication system using 2.4 GHz ISM band provides equipment with worldwide applicability and helps standardize equipment. 6). Acquisition of qualification for the Japanese Radio Law, FCC and CE is planned. Upon successful acquisition, RF applications do not require individual acquisition of qualification for such standards, which creates shorter lead time for equipment development and lower costs. 859 FC User Manual 5-5 Togoshi 6 Chome, Shinagawa-Ku, Tokyo 142-8511 Japan 7). Compatible with decoded output of various IR communication formats, no change in equipment of application software is necessary, other than substituting previous IR receivers with this module. Equipment designing will thus be simpler. Integration to the end product The SMK Transceiver Module, model RXX9000-15XX has to be installed and used in accordance with the technical description/installation instructions provided by the manufacturer. For detail information concerning type approval of this module (e.g. where this module is already pre-approved) please contact the authorized local distributor or the manufacturer. The system may only be implemented in the configuration that was authorized. Note that any changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Specification 1). RF Standard: ZigBee RF4CE Specification Version 1.00 compatible 2). Supply Voltage: 2.1-3.4 VDC 3). Operation Temperature Range: -20ºC to +70ºC 4). Interface: UART (Note 5) 115.2 kbps and IR decoder data output 5). External Dimensions: 17mm× 42mm × 5mm (not including connector) 6). Frequency Range: 2400-2483.5 MHz 7). Modulation System: DSSS 8). Modulation Type: Offset-QPSK 9). Antenna: PCB Inverted F type 10). Transmission Distance: 20m min. (reference only) 859 FC User Manual 5-5 Togoshi 6 Chome, Shinagawa-Ku, Tokyo 142-8511 Japan Regulatory Information USA-Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the distance between the equipment and the receiver. -Connect the equipment to outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Labelling SMK Transceiver module RXX9000-15XX labelled as below. FCC ID:GT3FC008 859 FC User Manual 5-5 Togoshi 6 Chome, Shinagawa-Ku, Tokyo 142-8511 Japan The proposed FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, “Contains FCC ID:GT3FC008” shall be placed on the outside of final host system. Caution: Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Canada-Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of this device. L ‘ utilization de ce dispositif est autorisée seulement aux conditions suivantes…

Text truncated - open the document above for the full version.

Applicant/Grantee SMK Corporation FCC ID: GT3FC008 Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. Device is equipped with Metal shielding to cover RF section. Refer to external photos. Y 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. All inputs to the modules are buffered through logic (SC13123) inputs. Refer to Schematic Diagram. Y 3 The modular transmitter must have its own power supply regulation. Internal power regulators are in RF Transceiver Chipset. Refer to Block diagram. Y 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Device is equipped with PCB Inverted F antenna. Any connector isn’t used. Refer to external photos. Y 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no cou pling between Device was tested outside of the PC for full modular approval. Refer to setup photos. Y the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The proposed FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, “Contains FCC ID:GT3FC008” shall be placed on the outside of final host system. Y 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the Refer to “User’s Guide” Exhibit. Y application for equipment authorization. 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Meet RF exposure compliance Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.

SMK Corporation Model Name: RXX9000-15XX Label and Label Location EUT Back Side

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 7 CERTIFICATION TEST REPORT FOR TRANCEIVER MODULE MODEL NUMBER: RXX9000-15XX FCC ID: GT3FC008 IC: 3683A-FC008 REPORT NUMBER: 09J12958-1, Revision A ISSUE DATE: FEBRUARY 01, 2010 Prepared for SMK CORPORATION 5-5 TOGOSHI 6-CHOME SHINAGAWA-KU TOKYO 142-8511 JAPAN Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 09J12958-1A DATE: FEBRUARY 01, 2010 FCC ID: GT3FC008 IC: 3683A-FC008 Page 2 of 54 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By -- 12/17/09 Initial Issue T. Chan A 02/01/10 Corrected Antenna Gain & Added MPE Calculation T. Chan REPORT NO: 09J12958-1A DATE: FEBRUARY 01, 2010 FCC ID: GT3FC008 IC: 3683A-FC008 Page 3 of 54 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.....................................................................................5 2. TEST METHODOLOGY..........................................................................................................6 3. FACILITIES AND ACCREDITATION.....................................................................................6 4. CALIBRATION AND UNCERTAINTY....................................................................................6 4.1. MEASURING INSTRUMENT CALIBRATION................................................................6 4.2. SAMPLE CALCULATION...............................................................................................6 4.3. MEASUREMENT UNCERTAINTY.................................................................................6 5. EQUIPMENT UNDER TEST...................................................................................................7 5.1. DESCRIPTION OF EUT.................................................................................................7 5.2. MAXIMUM OUTPUT POWER........................................................................................7 5.3. DESCRIPTION OF AVAILABLE ANTENNAS................................................................7 5.4. SOFTWARE AND FIRMWARE......................................................................................7 5.5. WORST-CASE CONFIGURATION AND MODE...........................................................7 5.6. DESCRIPTION OF TEST SETUP..................................................................................8 6. TEST AND MEASUREMENT EQUIPMENT........................................................................10 7. ANTENNA PORT TEST RESULTS......................................................................................11 7.1. 802.15.4 MODE IN THE 2.4 GHz BAND......................................................................11 7.1.1. 6 dB BANDWIDTH................................................................................................11 7.1.2. 99% BANDWIDTH................................................................................................15 7.1.3. OUTPUT POWER.................................................................................................19 7.1.4. AVERAGE POWER..............................................................................................20 7.1.5. POWER SPECTRAL DENSITY...........................................................................21 7.1.6. CONDUCTED SPURIOUS EMISSIONS..............................................................25 8. RADIATED TEST RESULTS................................................................................................32 8.1. LIMITS AND PROCEDURE..........................................................................................32 8.2. TRANSMITTER ABOVE 1 GHz...................................................................................33 8.2.1. TRANSMITTER ABOVE 1 GHz FOR 802.15.4 IN THE 2.4 GHz BAND.............33 8.3. RECEIVER ABOVE 1 GHz...........................................................................................42 8.3.1. RECEIVER ABOVE 1 GHz IN THE 2.4 GHz BAND............................................42 8.4. WORST-CASE BELOW 1 GHz....................................................................................43 9. AC POWER LINE CONDUCTED EMISSIONS....................................................................47 10. MAXIMUM PERMISSIBLE EXPOSURE.........................................................................51 11. SETUP PHOTOS..............................................................................................................54 REPORT NO: 09J12958-1A DATE: FEBRUARY 01, 2010 FCC ID: GT3FC008 IC: 3683A-FC008 Page 4 of 54 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. REPORT NO: 09J12958-1A DATE: FEBRUARY 01, 2010 FCC ID: GT3FC008 IC: 3683A-FC008 Page 5 of 54 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: SMK CORPORATION 5-5 TOGOSHI 6-CHOME SHINAGAWA-KU TOKYO 142-8511 JAPAN EUT DESCRIPTION: TRANCEIVER MODULE MODEL: RXX9000-15XX SERIAL NUMBER: 1B, 4C DATE TESTED: DECEMBER 9-16, 2009 APPLICABLE STANDARDS STANDARD TEST RESULTS CFR 47 Part 15 Subpart C Pass INDUSTRY CANADA RSS-210 Issue 7 Annex 8 Pass INDUSTRY CANADA RSS-GE…

Text truncated - open the document above for the full version.

REPORT NO: 09J12958-1A DATE: FEBRUARY 01, 2010 FCC ID: GT3FC008 IC: 3683A-FC008 Page 54 of 54 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 11. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 09J12958-1A DATE: FEBRUARY 01, 2010 FCC ID: GT3FC008 IC: 3683A-FC008 Page 55 of 54 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED RF MEASUREMENT SETUP RADIATED FRONT PHOTO REPORT NO: 09J12958-1A DATE: FEBRUARY 01, 2010 FCC ID: GT3FC008 IC: 3683A-FC008 Page 56 of 54 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED BACK PHOTO REPORT NO: 09J12958-1A DATE: FEBRUARY 01, 2010 FCC ID: GT3FC008 IC: 3683A-FC008 Page 57 of 54 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP LINE CONDUCTED FRONT PHOTO REPORT NO: 09J12958-1A DATE: FEBRUARY 01, 2010 FCC ID: GT3FC008 IC: 3683A-FC008 Page 58 of 54 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. END OF REPORT LINE CONDUCTED BACK PHOTO