GZM802140WEB PAD

User’s Manual W WT121 series 12 inch Wireless Thin Client ProScribe (Rev. 1.06 ) W  WT11 Copyright © This manual is copyrighted with all rights reserved. Under the copy rights law, this manual may not be copied, in whole or part, without written consent of Philips. Under the law, copying includes translating into another language or format. The monitor described in this manual, has been certified/registered by the safety agencies/regulatory authorities as model n° : CMPD1 FCC Notice This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, while can be determined by turning the equipment Off and On, the user is encouraged to try to correct the interference by one or more of the following measures. - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio TV technician for help. Modification The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. Cables Connections to this device must be made with shielded signals cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. The lighting flash with arrowhead symbol is intend to alert the user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electrical shock to people. The exclamation mark is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in literature accompanying the appliance. CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO AVOID THE RISK OF ELECTRICAL SHOCK. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING: THE ENCLOSURE HAS TO BE CHECKED UPON COLLISION DAMAGE; REFER TO QUALIFIED SERVICE PERSONNEL PROSCRIBE MONITOR, ACCESSORy DOCKING STATION AND AC/DC POWER ADAPTER DO NOT HAVE APPLIED PARTS, AND ARE NOT INTENDED TO BE CONNECTED TO A PATIENT CIRCUIT.  WT11 RF Exposure Statement This EUT is compliance with SAR for general population / uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET bulletin 65 Supplement C. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the pos- sibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 1.5 cm during normal operation. This device and its antenna (s) must not be co-located or operating in conjunction with any other antenna or transmitter.  WT11 INTRODUCTION A ruggedized wireless thin client display for the on-the-go computing The Philips ProScribe is a ruggedized wireless thin client display, released with Windows XP embedded for the on-the-go comput- ing, both for ITE and medical applications. The ProScribe suits all applications in to vertical markets where users meet to take it with them, while away from their desk. It’s a “cordless display” which makes use of wireless technology and thin-client computing to allow mobile workers to access applica- tions stored on a central server as if they were sitting behind their desktop monitor. Its ruggedized design, compact size and touch- screen interface makes it also a perfect solution for point of information and system control applications too. Designed for healthcare providers or any organization with highly mobile employees The ProScribe addresses the growing demand for mobile computing solutions among healthcare providers and medical system sup- pliers, who need immediate, portable and secure access to on-line data. Target users are: • nurses doing morning rounds want to enter blood pressure, temperature and other relevant data into a patient electronic record without handling any paper work; • doctors visiting patients on the ward wish to prescribe medication and make laboratory appointments on the spot • medical professionals who can reduce their administrative workload, improve the accuracy of clinical decisions and improve patient care The ProScribe can be of equal benefit for any other organization employing mobile workforces like factory supervisors, field service engineers and retail sales employees to name but a few. The ProScribe gives such employees instant and handheld access to accu- rate data anytime anywhere. Made to be mobile With a 1GHz VIA-based x86 processor as its engine and Microsoft Windows XP embedded as operation system, the ProScribe offers a technologically powerful platform for mobile computing in enterprise applications. Other main features are: • 12.1 inch TFT-LCD with Touch-screen functionality; • 1024x768 resolution (XGA); • display emulated keyboard; • integrated WiFi™ 802.11b/g wireless LAN • lightweight (1,75kg); • hot-swappable battery • upright stand and hand-carrying-strap. Rugged design for the toughest environments The ProScribe is compliant with industry standards for liquid and dust resistance (IP5) and is also physically tough, with a highly durable build capable of survivi…

Text truncated - open the document above for the full version.

E Fimi S.r.l. Reliability Engineering W S&R * Department REF.: Issue date: 17-07-2007 Sheet 1 of 1 PROSCRIBE Mod. numb. CMPD12 – FCC ID numb. GZM802140 Photo 1 – Front side Photo 2 Left side Photo 3 – Right side Photo 4 – Back side Photo 5 – Bottom (Cradle adapter connector)

LABEL LOCATION ON PROSCRIBE CMPD12 REAR COVER 22 – June - 2007

MODEL NO. C MP D 1 2 INPUT RA TING : 19V 3.42A This devicecomplieswith part 15 o f theFCC R ules. O perationis s ubject tothe followingtwoconditions: ( 1) thisdevice may n ot c ause h armful interferenceand (2)this devicemust accept a ny interferencereceived including interferencethat may c ause u ndesiredoperation. This C lass B digital apparatusdevice c omplieswith C anadianICE S -003. C et a ppareil numerique dela c lasseB e st c onformeala n ormeN MB -003 WARN ING : A)Dis connect supply beforeservicing. B )N ever r emovecovers u nlessqualied todo s o. This u nit contains dangerous voltages. M ADE IN TAIWAN FCC ID: GZM 802140 IC: 6319A-802140

E Fimi S.r.l. Reliability Engineering W S&R * Department REF.: Issue date: 13-07-2007 Sheet 1 of 5 PROSCRIBE Mod. numb. CMPD12 – FCC ID numb. GZM802140 Photo 1 – LCD Panel with touch panel (front) Photo 2 LCD Panel (Back) Photo 3 – LCD panel bracket Photo 4 – Boards (total view) EMI SHIELD BACK LIGHT CONNECTOR TOUCH PANEL CONNECTOR LVDS CONNECTOR S&R * Department REF.: Issue date: 13-07-2007 Sheet 2 of 5 Photo 5 – Control board (front) Photo 6 – Control board (front) Photo 7 – Button board and WI-FI led (front) Photo 8 - Button board and WI-FI led (rear) Photo 9 – Mother board (front) Photo 10 – Mother board (CPU side) Flash disk Slot for PCMCIA devices S&R * Department REF.: Issue date: 13-07-2007 Sheet 3 of 5 Photo 11 – Battery module (front) Photo 12 – Battery module (rear) Photo 13 – Inverter board (front) Photo 14 – Inverter board (rear) Photo 15 – Cradle connector adapter board (front) Photo 16 – Cradle connector adapter board (rear) S&R * Department REF.: Issue date: 13-07-2007 Sheet 4 of 5 Photo 17– I/O board connector (front) Photo 18 – I/O board connector (rear) Photo 19 – I/O board connector (details) Power in connector Microphone input Headphone output USB USB VGAVideo output Ethernet RJ45 Reset switch S&R * Department REF.: Issue date: 13-07-2007 Sheet 5 of 5 Photo 20 – I/O board connector (front) Photo 21 I/O board connector (rear) Photo 21– Battery module (front) Photo 22 - Battery module (rear) Photo 23 – Wi-Fi module (front) Photo 24 Wi-Fi module (rear)

1 INTERNAL PHOTOS Wi-Fi fron module - Label 22 – June - 2007 Wi-Fi Module 2 Wi-Fi rear module - Label 22 – June - 2007

©2007 SPORTON International Inc. SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev. 03 FCC SAR Test Report Test Report No ﹕ FA733103-1-2-01 Specific Absorption Rate (SAR) Test Report for MoBitS Electronics, Inc. on the Web Pad Report No. : FA733103-1-2-01 Trade Name : MoBits / PHILIPS Model Name : MONTBLANC_12 / CMPD12 FCC ID : RUJ-LR802UKG Date of Testing : Jul. 26, 2007 Date of Report : Aug. 15, 2007 Date of Review : Aug. 15, 2007 ‚ The test results refer exclusively to the presented test model / sample only. ‚ Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. ‚ Report Version: Rev. 03 SPORTON International Inc. 6F, No.106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. ©2007 SPORTON International Inc. SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev. 03 Tel: 886-2-2696-2468 Fax: 886-2-2696-2255 FCC SAR Test Report Test Report No ﹕ FA733103-1-2-01 Table of Contents 1. Statement of Compliance ............................................................................................................................................................ 1 2. Administration Data..................................................................................................................................................................... 2 2.1 Testing Laboratory ........................................................................................................................................................... 2 2.2 Detail of Applicant............................................................................................................................................................ 2 2.3 Detail of Manufacturer ..................................................................................................................................................... 2 2.4 Application Detail............................................................................................................................................................. 2 3. Scope ............................................................................................................................................................................................ 3 3.1 Description of Device Under Test (DUT).......................................................................................................................... 3 3.2 Product Photo.................................................................................................................................................................. 4 3.3 Applied Standards: .......................................................................................................................................................... 5 3.4 Device Category and SAR Limits .................................................................................................................................... 6 3.5 Test Conditions ................................................................................................................................................................ 6 3.5.1 Ambient Condition:............................................................................................................................................ 6 3.5.2 Test Configuration: ............................................................................................................................................ 6 4. Specific Absorption Rate (SAR) ................................................................................................................................................. 7 4.1 Introduction...................................................................................................................................................................... 7 4.2 SAR Definition ................................................................................................................................................................. 7 5. SAR Measurement Setup ............................................................................................................................................................ 8 5.1 DASY4 E-Field Probe System ..................................................................................................... .................................... 9 5.1.1 ET3DV6 E-Field Probe Specification............................................................................................................... 10 5.1.2 ET3DV6 E-Field Probe Calibration.................................................................................................................. 10 5.2 DATA Acquisition Electronics (DAE) ...............................................................................................................................11 5.3 Robot............................................................................................................................................................................. 12 5.4 Measurement Server ..................................................................................................................................................... 12 5.5 SAM Twin Phantom ....................................................................................................................................................... 12 5.6 Data Storage and Evaluation ......................................................................................................................................... 14 5.6.1 Data Storage ................................................................................................................................................... 14 5.6.2 Data Evaluation ...........................................................................................................…

Text truncated - open the document above for the full version.

FCC.TR. TEST REPORT 07.858 Prima Ricerca & Sviluppo Srl soggetta a direzione e coordinamento da parte della Giovanni Maspero & C. S.p.A. – C.I. 02634780130 Sede legale : 22100 Tavernola (CO) Via Conciliazione, 1 Cod. FISC. e N. R.I. CO 02635860139 Sede operativa : Laboratori Via Campagna, 92 22020 Faloppio fraz. Gaggino (CO) Tel. +39 03135000.11 Fax +39 031991309Fax +39 031991309 EQUIPMENT UNDER TEST : APPARECCHIO IN PROVA : PROSCRIBE CMPD12 REFERENCE STANDARDS : NORME DI RIFERIMENTO : 47 CFR FCC Part 15 Subpart C § 15.247 CUSTOMER: RICHIEDENTE: • Dept. / Firm : Ente / Società’: FIMI S.R.L. • Mr.: Sig.: MARINO FUSCO • Address: Indirizzo: VIA SAUL BANFI, 1 – 21047 SARONNO (VA) - ITALY • Tel. : Telefono : ++39 02/96175248 • Telefax Fax : ++39 02/96175296 • E-mail: e-mail [email protected] Site of test execution: Via Campagna, 92 - 22020 Gaggino Faloppio (CO) - Italy Località esecuzione prove: Date of test samples receipt: 13/06/2007 Date of start test: 14/06/2007 Data ricevimento campioni: Data inizio prove: Date of end test: 15/06/2007 Data fine prove: Witness to the test: Presenti alle prove: Tested by: Testato da: Approved by: Approvato da: Nobody / Nessuno ......................................................... .......................................................... Massimiliano Tallariti Massimo Maltempi .......................................................... Massimo Maltempi The test results recorded in this Test Report are exclusively referred to the tested samples. I risultati del presente rapporto di prova si riferiscono esclusivamente al campione sottoposto a prova. Reproduction of this EMC-Test Report in whole or in part is prohibited without the written authorization of the Laboratory Director La riproduzione di questo Rapporto in modo parziale o totale è PROIBITO senza l’autorizzazione scritta della Direzione del Laboratorio Edition: 1.0 Issue date: 15/06/2007 sheet 1 of 19 FCC.TR. TEST REPORT 07.858 Prima Ricerca & Sviluppo Srl soggetta a direzione e coordinamento da parte della Giovanni Maspero & C. S.p.A. – C.I. 02634780130 Sede legale : 22100 Tavernola (CO) Via Conciliazione, 1 Cod. FISC. e N. R.I. CO 02635860139 Sede operativa : Laboratori Via Campagna, 92 22020 Faloppio fraz. Gaggino (CO) Tel. +39 03135000.11 Fax +39 031991309Fax +39 031991309 0. CONTENTS Page RevDate 0. CONTENTS...............................................................................................2 1. TECHNICAL INFORMATION OF EQUIPMENT UNDER TEST (EUT)......3 1.1 Identification.........................................................................................3 1.2 Technical data......................................................................................3 15/06/07 0 15/06/07 0 15/06/07 0 15/06/07 0 15/06/07 0 1.3 Modifications incorporated in E.U.T......................................................4 15/06/07 0 1.4 Ports identification ...............................................................................4 15/06/07 0 1.5 Auxiliary equipment.............................................................................5 15/06/07 0 2. TEST CONDITIONS..................................................................................5 15/06/07 0 2.1 Operating test modes and test conditions ...........................................5 15/06/07 0 2.2 Test overview.......................................................................................5 15/06/07 0 3. REFERENCE STANDARD FOR PERFORMED TESTS...........................6 15/06/07 0 4. Summary of test results.............................................................................6 15/06/07 0 4.1 Emission tests......................................................................................6 15/06/07 0 Note: .........................................................................................................6 15/06/07 0 5. TEST RESULTS........................................................................................7 15/06/07 0 6. EUT TECHNICAL DOCUMENTATION....................................................13 15/06/07 0 6.1 Wiring diagrams.................................................................................13 15/06/07 0 6.2 Technical manual...............................................................................13 15/06/07 0 6.3 Photographic documentation..............................................................14 Edition: 1.0 Issue date: 15/06/2007 sheet 2 of 19 FCC.TR. TEST REPORT 07.858 Prima Ricerca & Sviluppo Srl soggetta a direzione e coordinamento da parte della Giovanni Maspero & C. S.p.A. – C.I. 02634780130 Sede legale : 22100 Tavernola (CO) Via Conciliazione, 1 Cod. FISC. e N. R.I. CO 02635860139 Sede operativa : Laboratori Via Campagna, 92 22020 Faloppio fraz. Gaggino (CO) Tel. +39 03135000.11 Fax +39 031991309Fax +39 031991309 1. TECHNICAL INFORMATION OF EQUIPMENT UNDER TEST (EUT) 1.1 Identification Brand name: FIMI S.R.L Manufacturer: FIMI S.R.L Equipment : PROSCRIBE CMPD12 + WITH POWER SUPPLY TOUCH ELECTRONIC MOD :A3-60S17R-W Serial number : Not present FCC ID : GZM802140 Country of manufacturer: ITALY 1.2 Technical data FCC class: 47 CFR FCC Part 15 Subpart C § 15.247 Product type: WLAN Radio type: Intentional transceiver Power type : Power adapter Modulation: DSS for IEEE 802.11b; OFDM for IEEE 802.11g Data Modulation : DSS (BPSK / QPSK / CCK) ; OFDM (BPSK / QPSK / 16QAM / 64 QAM) Data Rate (Mbps) : DSS (1 / 2 / 5.5 / 11) ; OFDM (6/ 9 / 12 / 18 / 24 / 36 / 48 / 54) Frequency range : 2412 – 2462 MHz Channel number : 11 Channel Band Width (99%) : 11b:14.04 MHz; 11g:16.40 MHz Conducted Output Power : 11b:18.11 dBm; 11g:12.79 dBm Carrier Frequency : Channel No.1: 2412 MHz Channel No.2: 2417 MHz Channel No.3: 2422 MHz Channel No.4: 2417 MHz Channel No.5: 2432 MHz Channel No.6: 2437 MHz Channel No.7: 2442 MHz Channel No.8: 2447 MHz Channel No.9: 2452 MHz Channel No.10: 2457 MHz Channel No.11: 2462 MHz Field Antenna : Antenna Type: PIFA Antenna Connector:…

Text truncated - open the document above for the full version.

Report No.: RF960323L04 1 Report Format Version 2.0.5 FCC TEST REPORT REPORT NO.: RF960323L04 MODEL NO.: LR802UKG RECEIVED: Mar. 23, 2007 TESTED: Mar. 29 ~ May 10, 2007 ISSUED: May 15, 2007 APPLICANT: Qcom Technology Inc. ADDRESS: 7F, NO.178, MING CHUAN E. RD. SEC 3, TAIPEI TAIWAN R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 71 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF960323L04 2 Report Format Version 2.0.5 Table of Contents 1. CERTIFICATION .........................................................................................................................4 2. SUMMARY OF TEST RESULTS.................................................................................................5 2.1 MEASUREMENT UNCERTAINTY ..............................................................................................5 3. GENERAL INFORMATION .........................................................................................................6 3.1 GENERAL DESCRIPTION OF EUT............................................................................................6 3.2 DESCRIPTION OF TEST MODES..............................................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST.........................................................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .............................................8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS...........................................................10 3.4 DESCRIPTION OF SUPPORT UNITS......................................................................................10 4. TEST TYPES AND RESULTS ...................................................................................................11 4.1 CONDUCTED EMISSION MEASUREMENT............................................................................11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT.........................................................11 4.1.2 TEST INSTRUMENTS ..............................................................................................................11 4.1.3 TEST PROCEDURES ...............................................................................................................12 4.1.4 DEVIATION FROM TEST STANDARD .....................................................................................12 4.1.5 TEST SETUP ............................................................................................................................13 4.1.6 EUT OPERATING CONDITIONS..............................................................................................13 4.1.7 TEST RESULTS ........................................................................................................................14 4.2 RADIATED EMISSION MEASUREMENT .................................................................................20 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT ..............................................................20 4.2.2 TEST INSTRUMENTS ..............................................................................................................21 4.2.3 TEST PROCEDURES ...............................................................................................................22 4.2.4 DEVIATION FROM TEST STANDARD .....................................................................................22 4.2.5 TEST SETUP ............................................................................................................................23 4.2.6 EUT OPERATING CONDITIONS..............................................................................................23 4.2.7 TEST RESULTS ........................................................................................................................24 4.3 6DB BANDWIDTH MEASUREMENT........................................................................................38 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT.....................................................................38 4.3.2 TEST INSTRUMENTS ..............................................................................................................38 4.3.3 TEST PROCEDURE .................................................................................................................39 4.3.4 DEVIATION FROM TEST STANDARD .....................................................................................39 4.3.5 TEST SETUP ............................................................................................................................39 4.3.6 EUT OPERATING CONDITIONS..............................................................................................39 4.3.7 TEST RESULTS ........................................................................................................................40 4.4 MAXIMUM PEAK OUTPUT POWER ........................................................................................46 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT ........................................46 4.4.2 INSTRUMENTS.........................................................................................................................46 4.4.1 TEST PROCEDURES ...............................................................................................................47 4.4.2 DEVIATION FROM TEST STANDARD ........................…

Text truncated - open the document above for the full version.