H38UPUR-8DR-81DRWireless Mircophone Receiver

R UP-8DR/8H/8P SERIES No.1, Lane 17, Sec. 2, Han Shi West Road, Taichung, 401 TAIWAN Tel:886-4-22313737 Fax:886-4-22346757 http://www.show-pa.com e-mail: [email protected] All rights reserved to SEIKAKU. All features and content might be changed without prior notice. Any photocopy, translation, or reproduction of part of this manual without written permission is forbidden. Copyright 2006 SEIKAKU GROUP c NF02502-1.0 IMPORTANT! Please read this manual carefully before operating this unit for the first time. All rights reserved to SHOW. All features and content might be changedwithout prior notice. Any photocopy, translation, or reproduction of part ofthis manual without written permission is forbidden. SAFETY RELATED SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The symbol is used to indicate that somehazardous live terminals are involvedwithin this apparatus, even under thenormal operating conditions.The symbol is used in the service do-cumentation to indicate that specificcomponent shall be only replaced bythe component specified in that docu-mentation for safety reasons.Protective grounding terminal. Alternating current /voltage. ON: Denotes the apparatus turns on. OFF: Denotes the apparatus turns off, be- cause of using the single pole switch, be sureto unplug the AC power to prevent any ele-ctric shock before you proceed your service.WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the user.CAUTION: Describes precautions that should be observed to prevent danger of theapparatus. WARNING Power Supply Ensure the source voltage matches thevoltage of the power supply before turning ON the apparatus.Unplug this apparatus during lightningstorms or when unused for long periods of time. External Connection The external wiring connected to the out-put hazardous live terminals requires installation by an instructed person, or the use of ready-made leads or cords. Do not Remove any Cover There are maybe some areas with highvoltages inside, to reduce the risk of electricshock, do not remove any cover if the powersupply is connected.The cover should be removed by the qual-ified personnel only.No user serviceable parts inside. Fuse To prevent a fire, make sure to use fuseswith specified standard (current, voltage,type). Do not use a different fuse or shortcircuit the fuse holder.Before replacing the fuse, turn OFF theapparatus and disconnected the powersource. Protective Grounding Make sure to connect the protective grounding to prevent any electric shock before turning ON the apparatus.Never cut off the internal or external pro-tective grounding wire or disconnect the wiring of protective grounding terminal. Operating Conditions This apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on this apparatus.To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.Do not use this apparatus near water.Install in accordance with the manufacturer's Hazardous live terminal . Disposing of this product should not be placed in municipal waste and should be separate collection. 6.3 Certificate Remark: 1. The values with underlines should be scanned manually by adjusting UP/DOWN key.2. The following channels can be used simultaneously without any interference. Group 1-1: 798.125 Group 2-1: 798.325 Group 2-2: 800.725 Group 2-5: 807.925 Group 3-4: 805.725 Group 5-1: 798.925 Group 5-8: 815.725 Group 7-1: 799.325 Group 8-6: 811.525 Group 12-2: 802.725 IMPORTANT SAFETY INSTRUCTIONS Read these instructions.Keep these instructions.Heed all warnings. Only use attachments/accessories spec- ified by the manufacturer. Power Cord and Plug Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a thirdgrounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into youroutlet, consult an electrician for replace-ment of the obsolete outlet.Protect the power cord from being walk-ed on or pinched particularly at plugs,convenience receptacles, and the point where they exit from the apparatus. Cleaning When the apparatus needs a cleaning, youcan blow off dust from the apparatus witha blower or clean with rag etc. Don't use solvents such as benzol, alcohol,or other fluids with very strong volatility andflammability for cleaning the apparatus body.Clean only with dry cloth. Servicing Refer all servicing to qualified personnel. Toreduce t he risk of electric shock, do n ot performany servicing other than that contained in theoperating instructions unless you are qualifiedto do so . Servicing is required when the apparatus hasbeen damaged in any way ,such as powersupply cord or plug is damaged , liquid hasbeen spilled or objects have fallen into theapparatus, the apparatus has been exposedto rain or moisture, does not operate normally,or has been dropped. Follow all instructions. instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including am-plifiers) that produce heat. Do not block any ventilation openings. No naked flame sources, such as lighted candles, should be placed on the apparatus. 20 F 8 : 8 5 0 . 0 0 0 - 8 7 4 . 0 0 0 ( 8 5 0 - 8 7 9 ) M H z 123456789 101112 Group1 Group2 Group3 Group4 Group5 Group6 Group7 Group8 Group9 Group10 Group11 Group12 850.125 850.325 850.525 850.725 850.925 851.125 851.325 851.525 851.725 851.925 852.125 852.325 852.525 852.725 852.925 853.125 853.325 853.525 853.725 853.925 854.125 854.325 854.525 854.725 854.925 855.125 855.325 855.525 855.725 855.925 856.125 856.325 856.525 856.725 856.925 857.125 857.325 857.525 857.725 857.925 858.125 858.325 858.525 858.725 858.925 859.125 859.325 859.525 859.725 859.925 860.125 860.325 860.525 860.725 860.925 861.125 861.325 861.525 861.725 861.925 862.12…

Text truncated - open the document above for the full version.

R UP-81DR/8H/8P SERIES No.1, Lane 17, Sec. 2, Han Shi West Road, Taichung, 401 TAIWAN Tel:886-4-22313737 Fax:886-4-22346757 http://www.show-pa.com e-mail: [email protected] All rights reserved to SEIKAKU. All features and content might be changed without prior notice. Any photocopy, translation, or reproduction of part of this manual without written permission is forbidden. Copyright 2006 SEIKAKU GROUP c NF02715-1.0 IMPORTANT! Please read this manual carefully before operating this unit for the first time. All rights reserved to SHOW. All features and content might be changedwithout prior notice. Any photocopy, translation, or reproduction of part ofthis manual without written permission is forbidden. SAFETY RELATED SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The symbol is used to indicate that somehazardous live terminals are involvedwithin this apparatus, even under thenormal operating conditions.The symbol is used in the service do-cumentation to indicate that specificcomponent shall be only replaced bythe component specified in that docu-mentation for safety reasons.Protective grounding terminal. Alternating current /voltage. ON: Denotes the apparatus turns on. OFF: Denotes the apparatus turns off, be- cause of using the single pole switch, be sureto unplug the AC power to prevent any ele-ctric shock before you proceed your service.WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the user.CAUTION: Describes precautions that should be observed to prevent danger of theapparatus. WARNING Power Supply Ensure the source voltage matches thevoltage of the power supply before turning ON the apparatus.Unplug this apparatus during lightningstorms or when unused for long periods of time. External Connection The external wiring connected to the out-put hazardous live terminals requires installation by an instructed person, or the use of ready-made leads or cords. Do not Remove any Cover There are maybe some areas with highvoltages inside, to reduce the risk of electricshock, do not remove any cover if the powersupply is connected.The cover should be removed by the qual-ified personnel only.No user serviceable parts inside. Fuse To prevent a fire, make sure to use fuseswith specified standard (current, voltage,type). Do not use a different fuse or shortcircuit the fuse holder.Before replacing the fuse, turn OFF theapparatus and disconnected the powersource. Protective Grounding Make sure to connect the protective grounding to prevent any electric shock before turning ON the apparatus.Never cut off the internal or external pro-tective grounding wire or disconnect the wiring of protective grounding terminal. Operating Conditions This apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on this apparatus.To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.Do not use this apparatus near water.Install in accordance with the manufacturer's Hazardous live terminal . Disposing of this product should not be placed in municipal waste and should be separate collection. Remark: 1. The values with underlines should be scanned manually by adjusting UP/DOWN key.2. The following channels can be used simultaneously without any interference. Group 1-1: 798.125 Group 2-1: 798.325 Group 2-2: 800.725 Group 2-5: 807.925 Group 3-4: 805.725 Group 5-1: 798.925 Group 5-8: 815.725 Group 7-1: 799.325 Group 8-6: 811.525 Group 12-2: 802.725 IMPORTANT SAFETY INSTRUCTIONS Read these instructions.Keep these instructions.Heed all warnings. Only use attachments/accessories spec- ified by the manufacturer. Power Cord and Plug Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a thirdgrounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into youroutlet, consult an electrician for replace-ment of the obsolete outlet.Protect the power cord from being walk-ed on or pinched particularly at plugs,convenience receptacles, and the point where they exit from the apparatus. Cleaning When the apparatus needs a cleaning, youcan blow off dust from the apparatus witha blower or clean with rag etc. Don't use solvents such as benzol, alcohol,or other fluids with very strong volatility andflammability for cleaning the apparatus body.Clean only with dry cloth. Servicing Refer all servicing to qualified personnel. Toreduce t he risk of electric shock, do n ot performany servicing other than that contained in theoperating instructions unless you are qualifiedto do so . Servicing is required when the apparatus hasbeen damaged in any way ,such as powersupply cord or plug is damaged , liquid hasbeen spilled or objects have fallen into theapparatus, the apparatus has been exposedto rain or moisture, does not operate normally,or has been dropped. Follow all instructions. instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including am-plifiers) that produce heat. Do not block any ventilation openings. No naked flame sources, such as lighted candles, should be placed on the apparatus. 20 F 8 : 8 5 0 . 0 0 0 - 8 7 4 . 0 0 0 ( 8 5 0 - 8 7 9 ) M H z 123456789 101112 Group1 Group2 Group3 Group4 Group5 Group6 Group7 Group8 Group9 Group10 Group11 Group12 850.125 850.325 850.525 850.725 850.925 851.125 851.325 851.525 851.725 851.925 852.125 852.325 852.525 852.725 852.925 853.125 853.325 853.525 853.725 853.925 854.125 854.325 854.525 854.725 854.925 855.125 855.325 855.525 855.725 855.925 856.125 856.325 856.525 856.725 856.925 857.125 857.325 857.525 857.725 857.925 858.125 858.325 858.525 858.725 858.925 859.125 859.325 859.525 859.725 859.925 860.125 860.325 860.525 860.725 860.925 861.125 861.325 861.525 861.725 861.925 862.125 862.325 862.5…

Text truncated - open the document above for the full version.

R UR-81DRUP-8H/8P SERIES No.1, Lane 17, Sec. 2, Han Shi West Road, Taichung, 401 TAIWAN Tel:886-4-22313737 Fax:886-4-22346757 http://www.show-pa.com e-mail: [email protected] All rights reserved to SEIKAKU. All features and content might be changed without prior notice. Any photocopy, translation, or reproduction of part of this manual without written permission is forbidden. Copyright 2006 SEIKAKU GROUP c NF02500-1.0 IMPORTANT! Please read this manual carefully before operating this unit for the first time. All rights reserved to SHOW. All features and content might be changedwithout prior notice. Any photocopy, translation, or reproduction of part ofthis manual without written permission is forbidden. SAFETY RELATED SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The symbol is used to indicate that somehazardous live terminals are involvedwithin this apparatus, even under thenormal operating conditions.The symbol is used in the service do-cumentation to indicate that specificcomponent shall be only replaced bythe component specified in that docu-mentation for safety reasons.Protective grounding terminal. Alternating current /voltage. ON: Denotes the apparatus turns on. OFF: Denotes the apparatus turns off, be- cause of using the single pole switch, be sureto unplug the AC power to prevent any ele-ctric shock before you proceed your service.WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the user.CAUTION: Describes precautions that should be observed to prevent danger of theapparatus. WARNING Power Supply Ensure the source voltage matches thevoltage of the power supply before turning ON the apparatus.Unplug this apparatus during lightningstorms or when unused for long periods of time. External Connection The external wiring connected to the out-put hazardous live terminals requires installation by an instructed person, or the use of ready-made leads or cords. Do not Remove any Cover There are maybe some areas with highvoltages inside, to reduce the risk of electricshock, do not remove any cover if the powersupply is connected.The cover should be removed by the qual-ified personnel only.No user serviceable parts inside. Fuse To prevent a fire, make sure to use fuseswith specified standard (current, voltage,type). Do not use a different fuse or shortcircuit the fuse holder.Before replacing the fuse, turn OFF theapparatus and disconnected the powersource. Protective Grounding Make sure to connect the protective grounding to prevent any electric shock before turning ON the apparatus.Never cut off the internal or external pro-tective grounding wire or disconnect the wiring of protective grounding terminal. Operating Conditions This apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on this apparatus.To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.Do not use this apparatus near water.Install in accordance with the manufacturer's Hazardous live terminal . Disposing of this product should not be placed in municipal waste and should be separate collection. Remark: 1. The values with underlines should be scanned manually by adjusting UP/DOWN key.2. The following channels can be used simultaneously without any interference. Group 1-1: 798.125 Group 2-1: 798.325 Group 2-2: 800.725 Group 2-5: 807.925 Group 3-4: 805.725 Group 5-1: 798.925 Group 5-8: 815.725 Group 7-1: 799.325 Group 8-6: 811.525 Group 12-2: 802.725 IMPORTANT SAFETY INSTRUCTIONS Read these instructions.Keep these instructions.Heed all warnings. Only use attachments/accessories spec- ified by the manufacturer. Power Cord and Plug Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a thirdgrounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into youroutlet, consult an electrician for replace-ment of the obsolete outlet.Protect the power cord from being walk-ed on or pinched particularly at plugs,convenience receptacles, and the point where they exit from the apparatus. Cleaning When the apparatus needs a cleaning, youcan blow off dust from the apparatus witha blower or clean with rag etc. Don't use solvents such as benzol, alcohol,or other fluids with very strong volatility andflammability for cleaning the apparatus body.Clean only with dry cloth. Servicing Refer all servicing to qualified personnel. Toreduce t he risk of electric shock, do n ot performany servicing other than that contained in theoperating instructions unless you are qualifiedto do so . Servicing is required when the apparatus hasbeen damaged in any way ,such as powersupply cord or plug is damaged , liquid hasbeen spilled or objects have fallen into theapparatus, the apparatus has been exposedto rain or moisture, does not operate normally,or has been dropped. Follow all instructions. instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including am-plifiers) that produce heat. Do not block any ventilation openings. No naked flame sources, such as lighted candles, should be placed on the apparatus. 20 F 8 : 8 5 0 . 0 0 0 - 8 7 4 . 0 0 0 ( 8 5 0 - 8 7 9 ) M H z 123456789 101112 Group1 Group2 Group3 Group4 Group5 Group6 Group7 Group8 Group9 Group10 Group11 Group12 850.125 850.325 850.525 850.725 850.925 851.125 851.325 851.525 851.725 851.925 852.125 852.325 852.525 852.725 852.925 853.125 853.325 853.525 853.725 853.925 854.125 854.325 854.525 854.725 854.925 855.125 855.325 855.525 855.725 855.925 856.125 856.325 856.525 856.725 856.925 857.125 857.325 857.525 857.725 857.925 858.125 858.325 858.525 858.725 858.925 859.125 859.325 859.525 859.725 859.925 860.125 860.325 860.525 860.725 860.925 861.125 861.325 861.525 861.725 861.925 862.125 862.325 862…

Text truncated - open the document above for the full version.

UP-8DR UP-81DR UR-81DR

Produkte Products Prüfbericht - Nr.: Test Report No.: 16012001 001 Seite 18 von 20 Page 18 of 20 6 Photographs of the Test Set-Up Photograph 1: Set up for Conducted Emission on AC Mains Photograph 2: Set-up for Radiation Measurement Below 1GHz Produkte Products Prüfbericht - Nr.: Test Report No.: 16012001 001 Seite 19 von 20 Page 19 of 20 Photograph 3: Set-up for Radiation Measurement Above 1GHz