HCQ3B6OXNCUHigh Power Repeater

© Inovonics, 2011 - www.inovonics.com EN5040-T EchoStream ® High-Power Repeater Installation and Operation Manual - 05066J, May 18, 2011 1 Overview EN5040-T high-power repeaters receive, decode and retransmit signals at enhanced power from Inovonics Wireless nodes. They act as range expanders for any valid Inovonics Wireless transmission, including signals from other high-power repeaters. Repeaters can be layered as necessary, allowing Inovonics Wireless systems to scale from small commercial sites to complete campuses consisting of several buildings. The EN5040-T features jam detection, as well as case and wall tamper detection. Input power is provided by listed class 2 transformer, Ault Inc. T48141428V010G. Note: For UL installations, refer to the EN4216MR Installation and Operation Manual, the EN4232MR Installation and Operation Manual, or the EN7285 Installation Instructions. 1.1 Inovonics Wireless Contact Information If you have any problems with this procedure, contact Inovonics Wireless technical services: • E-mail: [email protected] • Phone: (800) 782-2709; (303) 939-9336 1.2 EN5040-T LEDs Decode LED: Flashes when any recognizable RF transmission is received. (Fig. 1). Transmit LED Lit when transmitting an RF transmission (Fig. 1). Low Battery Fault LED: Lit when the high-power repeaterhas a low battery (Fig. 1). Power LED: Lit when receiving power (Fig. 1). The LED lights green when the unit is receiving line power; red when receiving battery power. Note: If mapped to an output, the high-power repeater will send the AC loss message to the receiver or network coordinator when receiving power from the backup battery. Figure 1 EN5040-T LEDs 2 Installation and Startup 2.1 Installation Notes • These products are designed to be installed and maintained by professional security technicians. • Products are intended for indoor use. • Manually test all products weekly. 2.2 Connect Power Cabling Before beginning startup, power must be connected to the high-power repeater. To connect power to the high-power repeater: 1.Use a small screwdriver to press the housing release tab on the top or bottom of the high-power repeater (Fig. 2); separate the housing. 2.Connect power cabling (Fig. 2). • Wire should be two-conductor 20AWG (or larger) stranded-tinned copper with PVC insulation rated to 300 volts at 26°C (80°F). Wire length should not exceed 100 meters (328 feet). • Uses class 2 plug-in transformer 14VAC/120VAC-20VA, Ault Inc. T48141428V010G. Note: Do not secure transformer for Canadian installations. 2.3 Connect Battery Power The high-power repeater is shipped with a fully-charged backup battery. You will need to connect the battery: 1.Plug the connector cable from the backup battery into the battery connector (Fig. 2). 2.4 Select the Frequency Band EchoStream products are able to use a range of radio frequencies, and must be configured for your geographic area. To configure the high-power repeater: 1.Use a small screwdriver to press the housing release tab on the top or bottom of the receiver (Fig. 2); separate the housing. 2.Place a selection jumper on the appropriate frequency band selection pins (Fig. 2). • Place the jumper on the left two pins, marked AU, to set the frequency range to 915-928 MHz for Australia. • Place the jumper on the right two pins, marked NZ, to set the frequency range to 921-928 MHz for New Zealand. • Leave the jumper off the pins to set the frequency range to 902-928 MHz for North America. Note: North American is also selected when the jumper is only attached to one pin. This can prevent the jumper from being lost when selecting North America. Note: Only devices set for use in North America are configured for UL installations. 3.Press the Reset button. 2.5 Register the High-Power Repeater Although the high-power repeater is functional upon startup, Inovonics Wireless strongly recommends you register it using your receiver, network coordinator or control panel. Registration is required for UL installations. Inovonics Wireless recommends all high-power repeaters be supervised. Supervision is required for UL installations. Note: For registration information, refer to the receiver’s installation instructions. Caution: The reset bit will not be sent when the repeater has a low battery. Before registering the repeater, ensure the battery is fully charged. Figure 2 EN5040-T Components ADecode LEDBTransmit LEDCLow Battery Fault LED DPower LED A B D C AHousing release tabs BTamper buttonCPowerDTamper input EReset buttonFBackup batteryGBattery connector HTamper mounting hole IFrequency selection pins A A A C D F G B E H I © Inovonics, 2011 - www.inovonics.com 2 2.6 Mount the High-Power Repeater Caution: Mount the high-power repeater in a location removed from metal. Metal objects (duct work, wire mesh screens, boxes) will reduce RF range. 1.Use the provided anchors and screws to mount the high-power repeater in a location accessible for future maintenance. • In large installations, high-power repeaters should be mounted so that every transmitter has multiple transmission paths to the serial receiver or network coordinator. This kind of redundancy preserves system integrity in the event of temporary interruptions of any transmission path in the system. • For maximum efficiency, high-power repeaters should be mounted with as few obstacles as possible between it and the receiver, network coordinator or control panel. • Always perform a walk test after mounting, activating each transmitter assigned to the high-power repeater and ensuring an appropriate response. 2.7 Enable the Wall Tamper The wall tamper must be enabled. To enable the wall tamper. 1.Attach the included screw to the wall through the tamper mounting hole (Fig. 2). • If the EN5040-T is removed from the wall, the cutout on the back of the housing will detach from the EN5040-T, activating a tamper alarm. 2.8 Close the Housing The housing must be closed and the tamper spring in place to ensure the security of yo…

Text truncated - open the document above for the full version.

Request for Confidentiality Date: April 13, 2011 Subject: Confidentiality Request for: FCC ID: HCQ3B6OXNCU; IC ID 2309A-OXNCU Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ Inovonics Wireless Corporation has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 2 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. 1 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 2 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, Keal Vigil Production Control Specialist II

A u t h o r i t y t o A c t a s A g e n t Date: April 13, 2011 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: ______Keal Vigil______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: December 31, 2011 Keal Vigil Production Control Specialist II

May 23, 2011 This is to certify that Inovonics products EN5040 and EN5040‐T are all built on the same PC board and operate with the same firmware. The only difference is a low voltage (120VAC Input/14VAC Output) wall transformer power supply included in the EN5040‐T. Floyd Nishi Director of Mfg Engineering

EXTERNAL PHOTOS FCC ID:HCQ3B6OXNCU Industry Canada ID: 2306A‐OXNCU Products: EN5040, EN5040‐T Front Back

CONFIDENTIAL DOCUMENT LBL-FCC-EN5040 05068C CONFIDENTIAL DOCUMENTATION The information contained in this document is confidential to and the sole property of Inovonics Corporation. Receipt of this information requires the existence and full acceptance of the terms and conditions of a Non Disclosure Agreement signed by the Inovonics Corporation and the Recipient. This documentation is not to be reproduced or redistributed except as provided in the Non Disclosure Agreement. MATERIAL: : .002" THICK CLEAR MYLAR WITH .001" GLOSSY LAMINATION (FOR PROTEC- TION FROM INK SMEARING) AND PERMANENT ADHESIVE APPLIED TO THE BACKSIDE. RoHS COMPLIANT MATERIALS REQUIRED. ARTWORK: SUPPLIED BY INOVONICS. TEXT: BLACK. LABEL SIZE: 1.062" X .1.062" (SHOWN TO 3 TIMES SCALE) WITH .125 RADIUS ON EACH CORNER AND NO BORDER. PACKAGING AND LABEL ORIENTATION: LABELS TO BE SUPPLIED ON TOP SIDE OF ROLL STOCK WITH TEXT READABLE AS VIEWED FROM BOTTOM (SHORT) EDGE OF ROLL. Rev. Level DescriptionDate AInitial Release10/22/2007 BAdded CTICK logo4/21/2009 CUpdated for Echo optimization9/09/2010 © Inovonics 2010 EN5040 www.inovonics.com This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera- tion. FCC ID: HCQ3B6OXNCU / IC: 2309A-OXNCU

INTERNAL PHOTOS FCC ID:HCQ3B6OXNCU INDUSTRY CANADA: 2306A-OXNCU Products: EN5040, EN5040-T Front of PCB Bottom of PCB

S= power density P= power input to the antenna G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= distance to the center of radiation of the antenna Choose Occupational/Controlled General Population/Uncontrolled Tx Frequency: 928.00 (MHz) Maximum Peak Power at Antenna Input Terminal: 22.650 (dBm) Antenna gain : 4.00 (dBi) OET Bulletin 65, Edition 97-01 Prediction of MPE Limit Equation from page 18 2 4R PG S   4 R PG S   6.187W/m^2 S=0.6187 (mW/cm^2) 48.295 V/m of limit for S P=184.0772 (mW) G=2.5119 (numeric) R =7.7120(cm) S (mw/cm^2) at specific distance in cm Enter distance desired in cm 18.612V/M (Efield/m)0.0918881220

This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. EMC Report for Inovonics on the Model: EN5040 Page 1 of 68 TEST REPORT – EMC Emissions Report Number: 100257233DEN-001 Project Number: G100257233 Report Issue Date: 4/22/2011 Product Designation: Model: EN5040 Standards: FCC title 47 CFR part 15 subpart C RSS-210:2010 Issue 8 AS/NZS 4268:2008 Tested by: Client: Intertek Testing Services NA, Inc. 1795 Dogwood Street, Suite 200 Louisville, CO 80027 Inovonics 315 CTC Blvd. Louisville, CO 80027 Report prepared by Report reviewed by Randy Thompson Senior EMC Project Engineer Michael Spataro Engineering Team Leader Intertek Report Number: 100257233DEN-001 Issued: 4/22/2011 EMC Report for Inovonics on the Model: EN5040 Page 2 of 68 TABLE OF CONTENTS Section Page 1 Introduction and Conclusion .............................................................................................................. 4 2 Test Summary ...................................................................................................................................... 4 3 Description of Equipment Under Test................................................................................................ 6 4 System setup including cable interconnection details, support equipment and simplified block diagram ........................................................................................................................................................ 7 5 Radiated Emissions – Output Power of the Fundamental & Harmonics of the Fundamental...... 9 6 Radiated Emissions – Unintentional and Tx Spurious................................................................... 24 7 20dB Bandwidth ................................................................................................................................. 37 8 Number of Hopping Channels .......................................................................................................... 41 9 Hopping Channel Carrier Separation ............................................................................................... 43 10 Time of Occupancy (On/Off Time) ................................................................................................45 11 Band Edge Measurements............................................................................................................. 47 12 Occupied Bandwidth (OBW).......................................................................................................... 52 13 Duty Cycle & Duty Cycle Correction Factor................................................................................. 54 14 AC Conducted Emissions.............................................................................................................. 56 15 Measurement Uncertainty.............................................................................................................. 67 16 Revision History ............................................................................................................................. 68 Intertek Report Number: 100257233DEN-001 Issued: 4/22/2011 EMC Report for Inovonics on the Model: EN5040 Page 3 of 68 Product Tested: EN5040 (EchoStream Repeater) Intertek Report Number: 100257233DEN-001 Issued: 4/22/2011 EMC Report for Inovonics on the Model: EN5040 Page 4 of 68 1 Introduction and Conclusion The tests indicated in section 2.0 were performed on the product constructed as described in section 3.0. The remaining test sections are the verbatim text from the actual data sheets used during the investigation. These test sections include the test name, the specified test Method, a list of the actual Test Equipment Used, documentation Photos, Results and raw Data. No additions, deviations, or exclusions have been made from the standard(s) unless specifically noted. Based on the results of our investigation, we have concluded the product tested complies with the requirements of the standard(s) indicated. The results obtained in this test report pertain only to the item(s) tested. 2 Test Summary Section Test full name Test date Result 5 Radiated Emissions – Output power of the Fundamental & Harmonics of the Fundamental - FCC 247(b)(2) (d)/15.205 [Covers RSS-210, A8.4/ A8.5] 11/01/2010 03/26/2011 Pass 6 Radiated Emissions – Unintentional & Spurious - 15.247(d) FCC 15.209/109/205 [Covers RSS-210, A8.5 – RSS-GEN, Section 4.8 & 4.9] 03/19/2011 Pass 7 20 dB Bandwidth – FCC 15.247 (a)(1)(i) [Covers RSS-210, A8.1(c)] 11/08/2010 Pass 8 Number of Hopping Channels – FCC 15.247(a)(1)(i) [Covers RSS-210, A8.1(c)] 11/08/2010 Pass 9 Hopping Channel Carrier Separation – FCC 15.247(a)(1) [Covers RSS-210, A8.1(b)] 11/08/2010 Pass 10 Channel Time of Occupancy (On/Off Time) – FCC 15.247(a)(1)(i) [Covers RSS-210, A8.1(c)] 11/08/2010 Pass 11 Band Edge Measurements – FCC 15.247(d) / 15.209 [Covers RSS-210, A8.5] 11/08/2010 03/19/2011 Pass 12 Occupied Bandwidth (OBW) – RSS-GEN, Section 4.6.1 11/08/2010 Pass 13 Duty Cycle & Duty Cycle Correction Factor – FCC 15.35 [Covers RSS-GEN, Section 4.5] 11/08/2010 N/A 14 AC Conducted Emissions – FCC 15.207/107 [Covers R…

Text truncated - open the document above for the full version.