HDCWLAN194XF2802.11 an PCIe Module

802.11 an PCIe Module WLAN194XF2 User’s Manual Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Country Code Statement This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: HDCWLAN194XF2 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Certification This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Declaración de exposición a la radiación de Canada: Este equipo cumple con los límites de exposición a la radiación de la IC establecidos para un ambiente no controlado. Este equipo se debe instalar y operar con una distancia mínima de 20 cm entre el radiador y su cuerpo. This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be a…

Text truncated - open the document above for the full version.

Adtran 901 Explorer Boulevard Huntsville Alabama United States 35806-2807 Tel: 256 963 8554 / Fax: 256 963 8250 DoC Attestation Letter Date: 2012/11/23 We Adtran, as the grantee of this project (FCC ID: HDCWLAN194XF2 / Brand Name: Adtran / Model No.: WLAN194XF2), would like to declare that the composite portion categorized as computer peripheral has been authorized under the Declaration of Conformity procedures (Sproton report No.: FD291831, FCC Test Firm Registration No.: 187376). The final product shall consequently comply with the FCC rule applied for DoC Procedure. Regards, FCC Grantee contact person information. Applicant’s company name : Adtran Applicant’s company address : 901 Explorer Boulevard Huntsville Alabama United States 35806-2807 Signature : _____________________________ Job Title and Dept. : Jeff Whitmire / Manager, Compliance Engineering E-Mail : [email protected] Tel. : 256 963 8554

Adtran 901 Explorer Boulevard Huntsville Alabama United States 35806-2807 Tel: 256 963 8554 / Fax: 256 963 8250 Confidential Letter Date: 2012/11/23 Federal Communications Commission Authorization and Evaluation Division FCC ID：HDCWLAN194XF2 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant Hereby requests confidential treatment of information accomparting this Application As outlined below: 1. Block Diagram 2. Circuit Diagram 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, Applicant’s company name : Adtran Applicant’s company address : 901 Explorer Boulevard Huntsville Alabama United States 35806-2807 Signature : _____________________________ Job Title and Dept. : Jeff Whitmire / Manager, Compliance Engineering E-Mail : [email protected] Tel. : 256 963 8554

Page No. : 22 Module Approval Request Letter Subject: Module Approval Date: 2012/11/23 FCC ID: HDCWLAN194XF2 Dear Reviewer, We, Sporton International Inc., are authorized by Adtran to have their state-of-the-art 802.11 an PCIe Module approved under module approval authorization. The application of this module is specified to mobile host equipment. The requirements regulated in Public Notice DA00-1407 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip AR9590B. 3. The requirement of power supply regulation: The part number of the power regulator is RT8010. 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 8. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance of MPE RF exposure rule. Please do not hesitate to contact me for any questions of this request letter. Thank you. Company name : Sporton International Inc. Company Address : No.8, Lane 724, Bo-ai St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. Signature : Name : Leo Huang Job Title : Manager

Adtran 901 Explorer Boulevard Huntsville Alabama United States 35806-2807 Tel: 256 963 8554 / Fax: 256 963 8250 Power of Attorney Date: 2012/11/23 Dear Sir, I hereby have entrusted the following person to be a proxy regarding application for Type Certification. Sporton International Inc. Address : No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. Name : Leo Huang Job Title : Manager e-mail : [email protected] I am therefore responsible for the contents of the application. Brand name and model type of the specified radio equipment: Adtran / WLAN194XF2 FCC ID: HDCWLAN194XF2 Product name: 802.11 an PCIe Module FCC Grantee contact person information. Applicant’s company name : Adtran Applicant’s company address : 901 Explorer Boulevard Huntsville Alabama United States 35806-2807 Signature : _____________________________ Job Title and Dept. : Jeff Whitmire / Manager, Compliance Engineering E-Mail : [email protected] Tel. : 256 963 8554

Report No.:291831 SPORTON International Inc. PAGE NUMBER : 1 OF 6 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 31, 2013 FAX : 886-2-2696-2255 Photographs of EUT Report No.:291831 SPORTON International Inc. PAGE NUMBER : 2 OF 6 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 31, 2013 FAX : 886-2-2696-2255 Report No.:291831 SPORTON International Inc. PAGE NUMBER : 3 OF 6 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 31, 2013 FAX : 886-2-2696-2255 Report No.:291831 SPORTON International Inc. PAGE NUMBER : 4 OF 6 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 31, 2013 FAX : 886-2-2696-2255 Report No.:291831 SPORTON International Inc. PAGE NUMBER : 5 OF 6 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 31, 2013 FAX : 886-2-2696-2255 Report No.:291831 SPORTON International Inc. PAGE NUMBER : 6 OF 6 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 31, 2013 FAX : 886-2-2696-2255

Report No.:291831 SPORTON International Inc. PAGE NUMBER : 1 OF 2 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 31, 2013 FAX : 886-2-2696-2255 Photographs of EUT Report No.:291831 SPORTON International Inc. PAGE NUMBER : 2 OF 2 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 31, 2013 FAX : 886-2-2696-2255

Report No.: FR291831 FCC ID: HDCWLAN194XF2 Page No. : B1 of B3 Appendix B. Maximum Permissible Exposure Report No.: FR291831 FCC ID: HDCWLAN194XF2 Page No. : B2 of B3 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 - - F/300 6 1500-100,000 - - 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 - - F/1500 30 1500-100,000 - - 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) ＝ d GP30 Power Density: Pd (W/m²) ＝ 377 2 E E ＝ Electric field (V/m) P ＝ Average RF output power (W) G ＝ EUT Antenna numeric gain (numeric) d ＝ Separation distance between radiator and human body (m) The formula can be changed to Pd ＝ 2 377 30 d GP   From the EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Report No.: FR291831 FCC ID: HDCWLAN194XF2 Page No. : B3 of B3 1.3. Calculated Result and Limit Antenna Type : Dipole Antenna Max Conducted Power for IEEE 802.11n 40MHz : 15.97dBm Antenna Gain (dBi) Antenna Gain (numeric) Average Output Power (dBm) Average Output Power (mW) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 7.00 5.0119 15.9747 39.5798 0.039484 1 Complies Antenna Type : Dipole Antenna Max Conducted Power for IEEE 802.11a: 27.79dBm Directional Antenna Gain (dBi) Antenna Gain (numeric) Average Output Power (dBm) Average Output Power (mW) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 7.00 5.0119 27.7927 601.5474 0.600095 1 Complies Note: Directional Antenna Gain = Test Antenna Gain + 10 log (Antenna quantity)

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw Report Format Version: 01 FCC RADIO TEST REPORT Applicant’s company Adtran Applicant Address 901 Explorer Boulevard Huntsville Alabama United States 35806-2807 FCC ID HDCWLAN194XF2 Manufacturer’s company Senao Networks, Inc. Manufacturer Address 3F, No. 529, Chung Cheng Rd., Hsintien,Taipei,Taiwan Product Name 802.11 an PCIe Module Brand Name Adtran Model Name WLAN194XF2 Test Rule Part(s) 47 CFR FCC Part 15 Subpart E § 15.407 Test Freq. Range 5150 ~ 5250MHz Received Date Sep. 12, 2012 Final Test Date Nov. 22, 2012 Submission Type Original Equipment Operating Mode Master Statement Test result included is for the IEEE 802.11n and IEEE 802.11a (5150 ~ 5250MHz) of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.10-2009, 47 CFR FCC Part 15 Subpart E and KDB 789033 D01 v01r02. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report No.: FR291831AA Report Format Version: 01 Page No. : i of ii FCC ID: HDCWLAN194XF2 Issued Date :Jan. 08, 2013 Table of Contents 1. CERTIFICATE OF COMPLIANCE ........................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT ............................................................................................................................ 2 3. GENERAL INFORMATION..................................................................................................................................... 3 3.1. Product Details ........................................................................................................................................................................................... 3 3.2. Accessories ................................................................................................................................................................................................. 6 3.3. Table for Filed Antenna ............................................................................................................................................................................. 7 3.4. Table for Carrier Frequencies ................................................................................................................................................................... 8 3.5. Table for Test Modes .................................................................................................................................................................................. 8 3.6. Table for Testing Locations........................................................................................................................................................................ 9 3.7. Table for Supporting Units ......................................................................................................................................................................... 9 3.8. Table for Parameters of Test Software Setting ....................................................................................................................................... 9 3.9. Test Configurations................................................................................................................................................................................... 10 4. TEST RESULT......................................................................................................................................................... 13 4.1. AC Power Line Conducted Emissions Measurement ......................................................................................................................... 13 4.2. 99% Occupied Bandwidth Measurement............................................................................................................................................ 17 4.3. Maximum Conducted Average Output Power Measurement ........................................................................................................ 24 4.4. Power Spectral Density Measurement.................................................................................................................................................. 26 4.5. Peak Excursion Measurement ................................................................................................................................................................ 31 4.6. Radiated Emissions Measurement......................................................................................................................................................... 35 4.7. Band Edge Emissions Measurement...................................................................................................................................................... 49 4.8. Frequency Stability Measurement......................................................................................................................................................... 53 4.9. Antenna Requirements ........................................................................................................................................................................... 55 5. LIST OF MEASURING EQUIPMENTS .................................................................................................................... 56 6. TEST LOCATION.................................................................................................................................................. 58 7. TAF CERTIFICATE OF ACCREDI…

Text truncated - open the document above for the full version.

Report No.: FR291831 FCC ID: HDCWLAN194XF2 Page No. : A1 of A6 Appendix A. Test Photos Report No.: FR291831 FCC ID: HDCWLAN194XF2 Page No. : A2 of A6 1. Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW Report No.: FR291831 FCC ID: HDCWLAN194XF2 Page No. : A3 of A6 2. Photographs of Radiated Emissions Test Configuration Test Configuration: 9kHz ~30MHz FRONT VIEW REAR VIEW Report No.: FR291831 FCC ID: HDCWLAN194XF2 Page No. : A4 of A6 Test Configuration: 30MHz~1GHz FRONT VIEW REAR VIEW Report No.: FR291831 FCC ID: HDCWLAN194XF2 Page No. : A5 of A6 Test Configuration: Above 1GHz FRONT VIEW REAR VIEW Report No.: FR291831 FCC ID: HDCWLAN194XF2 Page No. : A6 of A6 FRONT VIEW