HDWF10040802.11 b/g and Bluetooth module

Host Configuration and Integration Guide DAP Technologies is the leading manufacturer of rugged mobile computing solutions and services for any setting, including harsh environments. DAP designs and manufactures mobile computers for a range of demanding industries including Utilities, Field Service, Emergency Services, Public Safety, Transportation and Logistics. Our new product line will include an OEM wi-fi & Bluetooth combo module. We have CE5000B series which includes CE5320B and CE5240B (where the only difference is screen orientation) CE5000B Series We also have CE3000B series which includes only CE3240B for now CE3240B And we have CE8000B series which includes CE8640B (half VGA screen), CE8810B (full VGA screen) and CE8820B (wide VGA screen) CE8640B CE8810B & CE8820B A very important note is that all these products all have the same electronic design (same processor, FPGA, memory,...), so same design but different form factor to fit in our existing casings. The same OEM module will be used in all products with same antennas that are located on mainboards (PCB mounted). The electrical interface between OEM module and our mainboards is the same and the physical interface is a board-to-board connector. OEM 802.11bg/BT Combo Module Changes or modifications not expressly approved by DAP Technologies could void the user's authority to operate the equipment. In order to comply with the FCC RF exposure requirements this module must be installed in specific host configurations as defined in this document. For CE8000B series the antennas are installed on the main board with a least 2.5 cm spacing from the antennas to the bottom of the enclosure. The CE3000B and CE5000B series are hand held with the antennas installed on a piggyback board that is located below the LCD display. There is not provision for simultaneous transmission of BT and 802.11b/g. The end user manual for all final host configurations must include the following warning statement. In order to comply with FCC RF exposure requirements this module must not be transmitting simultaneously with optional PCMCIA wireless communication card. The final host configuration must be labeled as follows: • “Contains FCC ID: HDWF10040 and IC: 4609A-F10040” • “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”

August9th, 2006 EquipmentAuthorisationDivision FederalCommunicationsCommission 7435OaklandMills Road Columbia,MD 21046 FCC ID: HDWF10040 ProductName:WM-BG-MR-01 ReQuestfor Confidentialitv Pursuantto Sections0.457and 0.459of the commissionsrules,we herebyrequestthat the followingdocumentsbe held confidential: • Schematics • Blockdiagram • Operational& Technicaldescription Thesematerialscontaintradesecretsandproprietaryinformationand are not customarilyreleasedto the public.The publicdisclosureof this informationmightbe harmfulto the companyand provideunjustifiedbenefitsto our competitors. Dated this 9DayofAugust 2006 By:YvanGosselin Printed Title:V.P.Technologies Onbehalfof :DAPT<echno/ogies Telephone:418-681-7835#311

8-ThisequipmentisbelowthelowthresroldforSARevaluationundergeneralpublic exposuresconditionsatdistancesgreaterJhan2.5cm. AlitestinghasbeenperformedbyNEMKOCanada.Ifotherinformationisrequired, pleaserefertotestreportfromNEMKOC~nada. Dated this 22 Dayof September 2006 ÉricBoisvert Printed Title:ProjectManager(R&D) Onbehalfof : DAPTechnoI09'!es Telephone:418-681-7835#395

September22nd,2006 FederalCommunicationsCommission 445,TwelfthSt.,S.W. Washington,D.C. 20554 Towhomitmayconcern, WeareapplyingforLimitedModularApprovalforFCCID:HDWF10040asperFCC PublicNoticeDA00-1407. Belowisthedemonstrationofcomplianceforeachofthe8requirementsofPublic NoticeDA00-1407: 1-ThemodulartransmitterhasitsownRFshielding 2-ThemodulecontainsinternaiSRAMmemoryfortransmitqueuesandreceivedata buffering.Onthetransmissionpath,datat'romthehostsystemisqueuedinmemoryby thelocalCPU.TheMACretrievesdatafortransmissionattheappropriatetime. 3-Themodulehasitsownpowersupplyregulation.Refertoschematics 4-Antennasarenotlocatedonthemodule,theyarelocatedonapiggyboardinsideour product(thefinalassembly).Themodulehasbeentestedwiththeseantennasand complieswithFCCpart15.Theinstallationofthemoduleandtheconnectionsbetween themoduleandtheantennasareperformedbyourproductionpeopleandarenot accessiblebytheenduser.Thisisinternalltoourfinalproductsowecanassurethatno onecanmodifythisassembly.ThisisanotherreasonwhyweareapplyingforaLimited ModularApproval. 5-Themodulehasbeentestedintooneofourproductsandthecombinationofboth complieswithFCCpar15.Aliofourproductsarebatteryoperated.Weareapplyingfor aLimitedModularApprovalwithourproductmodelnumbersCE5320BW,CE5240BW, CE3240BW,CE8640BW,CE8810BWandCE8820BW.Alithesemodelscomefromthe sameelectronicplatform.Sofromoneproducttoanotheritisthesameelectronicand RFdesign.Theonlythingsthatchangeareformfactor,keypadandLCDdisplay.Refer todocument'DAPproductdescription'forpictures. 6-ThemodulewillhavealabelwithFCCIDandourproductwillalsohavealabelsaying thatthisproductcontainsFCCID:HDWF10040. 7- Sincewearenotthemanufacturerofthemodule,wedonothavethisinformation.But thespecificationofthemoduleconfirmthatthemodulecomplieswith802.11bIgand 802.15(Bluetooth).

Inside CE5000B Antennas Pcb RF Module installed

A A 28,1 mm TOP OF PCB TO BOTTOM OF EXPANSION DOOR (RD1) 31,55 mm TOP OF PCB TO BOTTOM OF THE UNIT (RD2) SECTION A-A WIFI ANTENNA PC BOARD MÉTRIQUE / METRIC ÉCHELLE/SCALE 1:2 DATE : APP PIÈCE : PART APPVL : 2006-09-25 JF LAPLANTE 1/1 DATE : DATE : DATE : DATE : APP : APPVL : VERIF : CHECK : DESSIN : DRAWING : CONCEPT : DESIGN : GE - CE8000B WIFI ANTENNA POSITION ANTENNA POSITION TITRE : TITLE : PROJET : PROJECT : 955 FERNAND-DUFOUR QUÉBEC, QC, CANADA G1M 3B2 TEL: 418.681.7833 FAX: 418.681.7734 WWW.DAPTECH.COM CE DOCUMENT EST LA PROPRIÉTÉ EXCLUSIVE DE DAP TECHNOLOGIES. EN AUCUN CAS, IL NE DEVRA ÊTRE DIVULGUÉ À QUICONQUE À MOINS D'UNE ENTENTE DE CONFIDENTIALITÉ SIGNÉE PAR LES DEUX PARTIES. THIS DOCUMENT IS DAP TECHNOLOGIES SOLE PROPERTY. IT CANNOT BE DISCLOSED WITHOUT A CONFIDENTIAL AGREEMENT SIGNED BY BOTH PARTIES. PAGE : NO DESSIN : DRAWING NO : MANUTENTION : RÉFÉRENCES : - DOCUMENT MANUFACTURIER PLAGE DE TOLÉRANCES : TOLERANCE CHART: FINITION : FINISH : COULEUR : COLOR : MATÉRIEL : MATERIAL : SPÉCIFICATIONS TECHNIQUES / TECHNICAL SPECS NOTES TECHNIQUES : TECHNICAL NOTES: 1- THIS PART NEEDS TO BE RoHS COMPLIANT ECO PAR / BY DATE DESCRIPTION REV X 0.5 mm X.X 0.25 mm X.XX 0.10 mm ANGLE 0.5

955, rue Fernand-Dufour Vanier(Ouebec) Canada61M 3B2 Tel.+1(418)681-1833 Fax+1(418)681-1134 September20th,2006 FederalCommunicationsCommission 445,TwelfthSt., S.W. Washington,D.C. 20554 To whomit mayconcern, Thisletteris to confirmthatour modelnumbersCE5320BW,CE5240BW,CE3240BW, CE8640BW,CE8810BWand CE8820BWthatuse a wi-fiand Bluetoothcombomodule fromUSImodelnumberWM-BG-MR-01,haveno provisionsforsimultaneous transmitting. /) tjf;;Ç//~ ËricBOiS~ ProjectManager DAPTechnologies Phone:418-681-7835#395 e-mail:[email protected]

RF Exposure Statement For hand held host configurations, the hand is located on the bottom casing of the unit under the keypad section. Both antennas are located inside the product and under the LCD. For handheld mobile computing devices. The antennas will always be located more than 20 cm form a persons body (excluding hands, wrist and feet) during normal hand held operation. The equipment complies with the general population / uncontrolled maximum permissible exposure requirements of cfr 47 section 1.1310 802.11 Output power 14.3 mW, Antenna Gain 2.75 numeric 802.11 Power flux density = 39.4/4/pi/20^2 = 0.00784 mW/cm^2 BT Output power 1.77 mW, Antenna Gain 1.86 numeric Bluetooth Power flux density = 3.3/4/pi/20^2 = 0.0006565 mW/cm^2 Fractional power flux density = 0.00784/1 + 0.0006565/1 = 0.0085 Limit = 1 There is no provision for simultaneous transmission of BT and 802.11bg For host configurations that lend themselves to lap to use. This equipment is below the low threshold for SAR evaluation under general public exposure conditions for distances greater than 2.5 cm. During normal usage the antennas will be more than 2.5 cm from the a persons body. For laptop host configurations the manufacturer will ensure that there is at least 2.5 cm fro the antenna to the bottom of the enclosure. 802.11 b/g peak output power 11.56 dBm antenna peak gain 4.4 dBi eirp 11.56 + 4.4 = 15.96 dbm, 39.4 mW Bluetooth peak output power 2.48 dBm antenna peak gain 2.7 dBi eirp 2.48 + 2.7 = 5.18 dBm, 3.3 mW Total combined eirp 39.4 + 3.3 = 42.7 mW Low threshold 120/2.480 = 48.4 mW

Test Report: 6W68668.3 Applicant: DAP Technologies 955 Fernand Dufour Vanier, Quebec G1M 3B2 Apparatus: B2B Wireless Lan + BT Combo Module FCC ID: HDWF10040 In Accordance With: FCC Part 15 Subpart C, 15.247 FHSS System and Digitally Modulated Radiators 902-928MHz, 2400 - 2483.5 MHz, 5725-5850MHz Tested By: Nemko Canada Inc. 303 River Road Ottawa, Ontario K1V 1H2 Authorized By: Jason Nixon, Telecom Specialist Date: September 6, 2006 Total Number of Pages: 37 Nemko Canada Inc. REPORT SUMMARY Report Number:6W68668.3 FCC ID:HDWF10040 Specification: FCC Part 15 Subpart C, 15.247 Report Summary These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15, Subpart C. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. The assessment summary is as follows: Apparatus Assessed: B2B Wireless Lan + BT combo module Specification: FCC Part 15.247, Subpart C Compliance Status: Complies Exclusions: None Non-compliances: None Report Release History: Original Release Author: Xu Jin, Wireless Specialist Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. Page 2 of 37 Nemko Canada Inc. REPORT SUMMARY Report Number:6W68668.3 FCC ID:HDWF10040 Specification: FCC Part 15 Subpart C, 15.247 TABLE OF CONTENTS Report Summary...........................................................................................................................................2 Section 1 : Equipment Under Test................................................................................................................4 1.1 Product Identification.................................................................................................................................4 1.2 Samples Submitted for Assessment............................................................................................................4 1.3 Technical Specifications of the EUT..........................................................................................................5 Section 2: Test Conditions............................................................................................................................6 2.1 Specifications.............................................................................................................................................6 2.2 Deviations From Laboratory Test Procedures ............................................................................................6 2.3 Test Environment.......................................................................................................................................6 2.4 Test Equipment...........................................................................................................................................6 Section 3: Observations................................................................................................................................7 3.1 Modifications Performed During Assessment ............................................................................................7 3.2 Record Of Technical Judgements...............................................................................................................7 3.3 EUT Parameters Affecting Compliance.....................................................................................................7 3.4 Test Deleted................................................................................................................................................7 Section 4: Results Summary.........................................................................................................................8 4.1 FCC Part 15 Subpart C, 15.247: Test Results.............................................................................................9 Appendix A: Test Results...........................................................................................................................10 Section 1. Power Line Conducted Emissions........................................................................................................10 Section 2. 20dB Bandwidth ..................................................................................................................................13 Section 3. Output Power .......................................................................................................................................16 Section 4. Spurious Emissions.............................................................................................................................20 Section 5. Channel Separation..............................................................................................................................28 Section 6. No of Hopping Channels and Occupancy Time...................................................................................30 Section 7. Supply Voltage Variation......................................................................................................................34 Appendix B : Setup Photographs...........................................................................................................…

Text truncated - open the document above for the full version.

Power line conducted emissions Radiated Emissions