HFS-GW03Smart Watch

Product Safety and Warranty Information GizmoWatch3™ 1 Health and Safety Information This section outlines the safety precautions associated with using the device. Important Safety Precautions Please read the safety and operation instructions before using your device or any accessories that came with it. Retain these instructions for future use. • Do not install your device in your vehicle or use it while driving. Using your device while driving could put you and others at greater risk of an accident causing serious injury, death, and property loss. You are re- sponsible for knowing and obeying the laws and regulations regarding the use of wireless devices in the areas where you drive. 2 • This device has been tested to be IPx8 compliant. Do not operate under water. If all covers are tightly closed, device is protected against water ingress to a maximum of 1.5 meter deep for up to 30 minutes. • Do not use your accessories (ex: charger) near water (for example, near a bathtub or a sink, in a wet basement, or near a swimming pool) or spill liquid of any kind on your device or accessories as this might cause a short circuit, a fire, or an electric shock which could cause serious injury, death, and property loss. • Do not use your device in the res- ence of gas fumes as it presents a risk of fire or explosion. • Do not use or store your device in extreme temperatures as your device might overheat and may present a burn and fire risk and cease to function. 3 • Do not dispose of your device in a fire as this might cause an explosion resulting in serious injury, death, and property loss. • Do not dispose of your device in a fire as this might cause an explosion resulting in serious injury, death, and property loss. • Federal Aviation Administration (FAA) and Federal Communications Commission (FCC) regulations prohibit using the radio of wireless devices while in the air. Turn off all wireless connections on your device before boarding an aircraft. Using your device on an aircraft might affect aircraft instrumentation, communication, and performance; might disrupt the network; might otherwise be dangerous to the oper- ation of the aircraft, its crew, and its passengers; and might be illegal. • Do not disassemble your device. Your device contains small parts that might be a choking hazard. 4 • Most modern electronic equipment is shielded from radio frequency (RF) signals. However, certain electronic equipment might not be shielded against the RF signals from your device. Keep your device away from medical devices, including pacemakers and hearing aids, as they might malfunction and cause serious injury or death to you and others. • Turn off all wireless connections on your device in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. • Certain jurisdictions might prohibit or restrict your use of certain fea- tures on your device. 5 Additional Safety Guidelines About Charging • Use only the charger supplied with your device. Use of another type of charger will result in malfunction and/or danger. • Do not use the charger in a high-moisture environment. Never touch the charger when your hands or feet are wet. • Allow adequate ventilation around the charger when using it to operate the device or charge the battery. Do not cover the charger with paper or other objects that will reduce cool- ing. Do not use the charger while it is inside a carrying case. • Connect the charger to a proper power source. The voltage require- ments are found on the product case and/or packaging. • Do not use the charger if the cord is damaged. 6 • Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture. About the Battery • This unit contains a non-replaceable internal Lithium Ion battery. • The battery can burst or explode, releasing hazardous chemicals. • To reduce the risk of fire or burns, do not disassemble, crush, punc- ture, or dispose of in fire or water. • Important instructions (for service personnel only) Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. • The battery must be recycled or disposed of properly. • Use the battery only in the specified equipment. 7 Caring for the Device Taking good care of your device will ensure trouble-free operation and reduce the risk of damage to your device: • Keep your device away from excessive moisture and extreme temperatures. • Do not place anything on top of your device or drop objects on your device. • Do not drop your device or subject it to severe shock. • Do not subject your device to sudden and severe temperature changes. This could cause moisture condensation inside the unit, which could damage your device. In the event of moisture condensation, allow your device to dry out com- pletely before use. 8 • The screen surface can easily be scratched. Avoid touching it with sharp objects. Non-adhesive generic screen protectors designed specifically for use on portable devices with LCD panels may be used to help protect the screen from minor scratches. • Never clean your device when it is turned on. Use a soft, lint-free cloth to wipe the screen and the exterior of your device. • Do not use paper towels to clean the screen. • Never attempt to disassemble, repair or make any modifications to your device. Disassembly, modifica- tion or any attempt at repair could cause damage to your device and even bodily injury or property dam- age and will void any warranty. • Do not store or carry flammable liquids, gases or explosive materials in the same compartment as your device, its parts or accessories. 9 • Do not expose your device to extreme heat or direct sunlight for prolonged periods. Overheating may damage your device. • Do not use alcohol or any abrasive material when cleani…

Text truncated - open the document above for the full version.

Get to know your device GizmoWatch3 TM Para la versión en español, visite verizonwireless.com/support. 2 Setting Up Your GizmoWatch Charging Your GizmoWatch Before you start, charge your watch completely. 1. Line up the gold pins on the charging cord with the charging contacts on the back of the watch. The watch and charging cord are magnetized and should connect without effort. NOTE: The image is for illustration purposes only and appearance of the actual wrist strap pattern may vary. 2. Plug the other end of the cord into the charging adapter and plug the adapter into an electrical outlet. 3 WARNING: Use only approved chargers with your device. Incompatible chargers or tampering with the charging contacts could damage your device and void the warranty. Preparing Your Smartphone Download the GizmoHub app from the Google Play™ Store or the Apple® App Store®. The GizmoHub app lets you set up, call, message, find and control your child’s GizmoWatch. Wearing Your GizmoWatch 1. Wrap the wristband around your child’s wrist, making sure that the camera is on top of the screen. 2. Slide the wristband through the buckle and adjust for comfort (A). 4 3. Insert the pin on the underside of the buckle into one of the holes on the wristband (B). 4. Slide the wristband through the loop (C). A C B 5 NOTE: The watch should fit snugly, but not too tightly, around your child’s wrist. Swapping the Loop Strap NOTE: Additional loop straps are supplied in three different colors: orange, green, and blue. 1. Pull the release knob all the way in the opposite direction (A). 2. Detach the wristband from your GizmoWatch (B). B A 6 3. Remove the loop strap from the wristband (C). 4. Replace the loop strap (D). C D 7 Replacing the Wristband 1. Insert the pin (the opposite side of the release knob) into the pin hole on your GizmoW atch (A). 2. Pull the release knob all the way in the opposite direction and align the other end of the pin with the hole on your GizmoWatch (B). Release the knob to lock the wristband in place. A B 8 Turning Your GizmoWatch On and Off To turn your watch on, press and hold the Power button until the screen lights up. To turn it off, press and hold the Power button until you see “POWER OFF WATCH?” on the screen. Then tap to turn off your watch. Activating and Pairing Your GizmoWatch Follow the instructions in the app and on your GizmoW atch to complete setup. 9 Using Your GizmoWatch NOTE: Screen images and icons are for illustration purposes only and may differ from the actual device. Adjusting the Volume Swipe to the left from the Watch screen until you see the Settings Menu. Tap to go to the Volume screen. Then drag around the circle to adjust the volume levels. Alternatively, you can use the bottom Increase (+) or Decrease (-) volume controls. 10 Making a Call 1. From the Watch screen, swipe left to open the Contact List. Then select the contact you want to call. 2. Tap to make audio call. 3. Tap to make video call. NOTE: Your GizmoWatch can only make and receive calls from phone numbers on your child’s Contact List. These numbers may be for mobile phones, landlines, and other Gizmo devices. You can manage the Contact List in the Gizmo Hub app. 11 Receiving a Call When someone from your child’s contact list calls the GizmoWatch, it will ring and the caller name will be shown on the screen. • To answer the call, tap . • To reject the call, tap . • To end the call, tap . TIP: To adjust the volume during the call, tap . NOTE: Making and receiving calls and messages requires a network connection. 12 Sending a Message 1. From the Watch screen, swipe left to open the Contact List. Then select the contact you want to message. 2. Tap to create a new message. Then: • To create a voice message, tap . • To choose from a list of pre- written messages, tap. • To send a emoji, tap . 13 Receiving a Message When the GizmoWatch receives a new message, it will appear on the Home screen. To reply, tap the contact. NOTE: Your GizmoWatch can only receive messages from contacts with the GizmoHub app or from other Gizmo devices if the sender is a GizmoBuddy. It can’t receive messages from non-Gizmo devices. 14 Additional information Your wireless device and third-party services Verizon is the mobile carrier associated with this wireless device, but many services and features offered through this device are provided by or in conjunction with third parties. Verizon is not responsible for your use of this device or any non–Verizon applications, services and products, including any personal information you choose to use, submit or share with others. Specific third-party terms and conditions, terms of use and privacy policies apply. Please review carefully all applicable terms, conditions and policies prior to using this wireless device and any associated application, product or service. 15 © 2022 Verizon. All Rights Reserved.

Quanta Computer Inc. NO.188, Wenhua 2nd Rd., Guishan Dist., Taoyuan City 33377, Taiwan TEL: +886-3-3272345 / FAX: +886-3-3961334 Date: September 13, 2022 We, Quanta Computer Inc. declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: HFS-GW03 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- Joyce Kuo / Director Quanta Computer Inc. Tel: +886-3-3272345 Fax: +886-3-3961334 E-mail: [email protected]

Quanta Computer Inc. NO.188, Wenhua 2nd Rd., Guishan Dist., Taoyuan City 33377, Taiwan TEL: +886-3-3272345 / FAX: +886-3-3961334 Date: 2022-09-13 FCC ID: HFS-GW03 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Parts list Tune Up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Joyce Kuo / Director Quanta Computer Inc. Tel: +886-3-3272345 Fax: +886-3-3961334 E-mail: [email protected]

Quanta Computer Inc. NO.188, Wenhua 2nd Rd., Guishan Dist., Taoyuan City 33377, Taiwan TEL: +886-3-3272345 / FAX: +886-3-3961334 Date: 2022-09-13 FCC ID: HFS-GW03 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- Joyce Kuo / Director Quanta Computer Inc. Tel: +886-3-3272345 Fax: +886-3-3961334 E-mail: [email protected]

Quanta Computer Inc. NO.188, Wenhua 2nd Rd., Guishan Dist., Taoyuan City 33377, Taiwan TEL: +886-3-3272345 / FAX: +886-3-3961334 Date: 2022-09-13 FCC ID: HFS-GW03 AUTHORIZATION LETTER To Whom It May Concern: Quanta Computer Inc. hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on Quanta Computer Inc.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- Joyce Kuo / Director Quanta Computer Inc. Tel: +886-3-3272345 Fax: +886-3-3961334 E-mail: [email protected]

FCC ID location  Side face  Bottom side FCC ID drawing: Top bottom

Reference No.: BCKT-WTW-P22080510_INT Page 1 / 13 CONSTRUCTION PHOTOS OF EUT Reference No.: BCKT-WTW-P22080510_INT Page 2 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 3 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 4 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 5 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 6 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 7 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 8 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 9 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 10 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 11 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 12 / 13 Reference No.: BCKT-WTW-P22080510_INT Page 13 / 13

SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 28 Report No. : SFBCKT-WTW-P22080510 Issued Date : Sep. 19, 2022 SAR Test Report Report No. : SFBCKT-WTW-P22080510 Applicant : Quanta Computer Inc. Address : NO.188, Wenhua 2nd Rd., Guishan Dist., Taoyuan City 33377, Taiwan Product : Smart Watch FCC ID : HFS-GW03 Model No. : QTAX57 FCC Rule Part : CFR §2.1093 Standards : IEC/IEEE 66209-1528:2020 KDB 865664 D01 v01r04, KDB 865664 D02 v01r02 KDB 248227 D01 v02r02, KDB 447498 D01 v06, KDB 941225 D05 v02r05 Sample Received Date : Aug. 15, 2022 Date of Testing : Aug. 17, 2022 ~ Aug. 24, 2022 Lab Address : No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location : No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City, Taiwan CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch–Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Lena Wang / Specialist Approved By : Gordon Lin / Manager FCC Accredited No.: TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 28 Report No. : SFBCKT-WTW-P22080510 Issued Date : Sep. 19, 2022 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY6 System ............................................................................................................................................... 6 3.2.1 Robot ............................................................................................................................................................... 7 3.2.2 Probes ............................................................................................................................................................. 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................. 8 3.2.4 Phantoms ......................................................................................................................................................... 8 3.2.5 Device Holder .................................................................................................................................................. 9 3.2.6 System Validation Dipoles ............................................................................................................................. 10 3.2.7 Power Source ................................................................................................................................................ 10 3.2.8 Tissue Simulating Liquids .............................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 13 3.4 SAR Measurement Procedure ................................................................................................................................... 14 3.4.1…

Text truncated - open the document above for the full version.

Plots of System Verification Report No. : SFBCKT-WTW-P22080510 Page No. : 1 of 9 Annex A. Plots of System Verification The plots for system verification are shown as follows. Plots of System Verification Report No. : SFBCKT-WTW-P22080510 Page No. : 2 of 9 Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/08/24 S01 System Check_H1750_220824 DUT: Dipole 1750 MHz; Type: D1750V2; SN: 1055 Communication System: UID 0, CW; Frequency: 1750 MHz;Duty Cycle: 1:1 Medium: H16T20N1_0824 Medium parameters used: f = 1750 MHz; σ = 1.333 S/m; ε r = 38.7; ρ = 1000 kg/m 3 Ambient Temperature：23.6 °C ; Liquid Temperature：23.1 °C DASY5 Configuration: - Probe: EX3DV4 - SN7472; ConvF(8.8, 8.8, 8.8) @ 1750 MHz; Calibrated: 2022/05/27 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1431; Calibrated: 2022/02/23 - Phantom: SAM Phantom_1982; Type: QD 000 P41 Ax; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.72 W/kg Pin=50mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 45.87 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 3.29 W/kg SAR(1 g) = 1.87 W/kg; SAR(10 g) = 1.01 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 2.81 W/kg Plots of System Verification Report No. : SFBCKT-WTW-P22080510 Page No. : 3 of 9 Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/8/24 S02 System Check_H750_220824 DUT: Dipole 750 MHz; Type: D750V3; SN: 1013 Communication System: UID 0, CW; Frequency: 750 MHz;Duty Cycle: 1:1 Medium: H06T09N1_0824 Medium parameters used: f = 750 MHz; σ = 0.902 S/m; ε r = 41.579; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C ; Liquid Temperature：23.2 °C DASY5 Configuration: - Probe: EX3DV4 - SN7736; ConvF(10.21, 10.21, 10.21) @ 750 MHz; Calibrated: 2022/5/30 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2022/6/1 - Phantom: SAM Phantom_1987; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (61x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.552 W/kg Pin=50mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 26.11 V/m; Power Drift = -0.03 dB Peak SAR (extrapolated) = 0.598 W/kg SAR(1 g) = 0.416 W/kg; SAR(10 g) = 0.280 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 0.544 W/kg Plots of System Verification Report No. : SFBCKT-WTW-P22080510 Page No. : 4 of 9 Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/8/24 S03 System Check_H2450_220824 DUT: Dipole 2450 MHz; Type: D2450V2; SN: 737 Communication System: UID 0, CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: H19T27N1_0824 Medium parameters used: f = 2450 MHz; σ = 1.806 S/m; ε r = 38.078; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C ; Liquid Temperature：23.2 °C DASY5 Configuration: - Probe: EX3DV4 - SN7736; ConvF(8.12, 8.12, 8.12) @ 2450 MHz; Calibrated: 2022/5/30 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2022/6/1 - Phantom: SAM Phantom_1987; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (81x81x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 4.12 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 49.09 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 5.18 W/kg SAR(1 g) = 2.42 W/kg; SAR(10 g) = 1.15 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 4.09 W/kg Plots of System Verification Report No. : SFBCKT-WTW-P22080510 Page No. : 5 of 9 Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/08/17 S04 System Check_H2450_220817 DUT: Dipole 2450 MHz; Type: D2450V2; SN: 737 Communication System: UID 0, CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: H19T27N1_0817 Medium parameters used (interpolated): f = 2450 MHz; σ = 1.848 S/m; ε r = 37.854; ρ = 1000 kg/m 3 Ambient Temperature：23.2 °C ; Liquid Temperature：23.0°C DASY5 Configuration: - Probe: EX3DV4 - SN3971; ConvF(7.98, 7.98, 7.98) @ 2450 MHz; Calibrated: 2022/01/25 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1277; Calibrated: 2022/01/19 - Phantom: Twin SAM Phantom_1885; Type: QD000P40CD; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (81x81x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 4.14 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 46.61 V/m; Power Drift = 0.08 dB Peak SAR (extrapolated) = 5.44 W/kg SAR(1 g) = 2.50 W/kg; SAR(10 g) = 1.19 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 4.32 W/kg Plots of System Verification Report No. : SFBCKT-WTW-P22080510 Page No. : 6 of 9 Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/8/24 S05 System Check_H1750_220824 DUT: Dipole 1750 MHz; Type: D1750V2; SN: 1055 Communication System: UID 0, CW; Frequency: 1750 MHz;Duty Cycle: 1:1 Medium: H16T20N1_0824 Medium parameters used: f = 1750 MHz; σ = 1.371 S/m; ε r = 39.115; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C ; Liquid Temperature：23.2 °C DASY5 Configuration: - Probe: EX3DV4 - SN7736; ConvF(8.71, 8.71, 8.71) @ 1750 MHz; Calibrated: 2022/5/30 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2022/6/1 - Phantom: SAM Phantom_1987; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.78 W/kg Pin=50mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Re…

Text truncated - open the document above for the full version.

Annex Z. Calibration Certificate for Probe and Dipole The SPEAG calibration certificates are shown as follows. Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Model：D750V3S/N：1013Measurement Date：2022/8/30 Frequency (MHz) Type Item Previous Measurement Annual Check Deviation Accepted Tolerance Result Real Impedance 53.57449.393-4.181±5ΩPASS Imaginary Impedance 0.25760.29900.04±5ΩPASS Return Loss -29.219-27.514-5.84%±20%PASS 750Free Space 750 MHz，Free Space Annual Confirmation of SAR Reference Dipole Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Model：D2450V2S/N：737Measurement Date： 2022/8/25 Frequency (MHz) Type Item Previous Measurement Annual Check Deviation Accepted Tolerance Result Real Impedance 53.98951.387-2.602±5ΩPASS Imaginary Impedance 4.29265.36051.07±5ΩPASS Return Loss -24.989-24.145-3.38%±20%PASS 2450 Free Space 2450 MHz，Free Space Annual Confirmation of SAR Reference Dipole Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510 Report No.: SFBCKT-WTW-P22080510

Report No.: RFBCKT-WTW-P22080510-4 R1 Page No. 1 / 26 Report Format Version: 6.1.1 Cancels and replaces the report no.: RFBCKT-WTW-P22080510-4 dated on Sep. 19, 2022 FCC Test Report (Co-Located) Report No.: RFBCKT-WTW-P22080510-4 R1 FCC ID: HFS-GW03 Test Model: …

Text truncated - open the document above for the full version.