HLEPA520BTNFRugged Mobile Computer

Rugged Mobile Computer - PA520 - User's Manual 400892G Preliminary © 2014 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. - I - This manual explains how to install, operate and maintain the PA520 Data Collection Terminal. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from the manufacturer. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. © Copyright 2014 Unitech Electronics Co., Ltd. All rights reserved. Unitech global website address: http://www.ute.com Bluetooth is a registered trademark of Bluetooth SIG. Microsoft, Windows and ActiveSync are either registered trademarks or trademarks of Microsoft Corporation. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Unitech is a member of Oracle Embedded Software Licensing Program. About This Manual Preface - II - Regulatory Compliance Statements FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. 1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. - III - FCC Label Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1.This device may not cause harmful interference, and 2.This device must accept any interference received, including interference that may cause undesired operation. RF Radiation Exposure Statement For body contact during operation, this rugged mobile computer has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of 0 mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Operations in 5150-5250 MHz band is for indoor use only. Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. European Conformity Statement Declaration of Conformity with regards to the R&TTE 1999/5/EC and EMC 89/336/ EEC directives. RoHS Statement This device conforms to RoHS (Reduction Of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. - IV - TaiwanNCC Warning Statement 交通部電信總局低功率電波輻射性電機管理辦法 (930322) 根據交通部低功率管理辦法規定： 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者 均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有 干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合 法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電 機設備之干擾。 Laser Information The Unitech PA520 series is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The PA520 series contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or prescribed service operations. The laser safety warning label required by the DHHS/IEC for the PA520 series' optional laser scanner module is located on the memory compartment cover, on the back of the unit. CAUTION! Use of controls or adjustments or per formance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner , including binoculars, microscopes, and magnifying glasses, with will increase eye damage. This does not include eyeglasses worn by the user. - V - Battery Notices The PA520 is equipped with a Lithium-Ion battery pack and backup battery. Both batteries will discharge after an extended period of not being used. When both batteries are discharged, recharge the unit for 4.5 hours in order to fully charge the main battery and backup battery. Recharge the PA520 through the following: 1.Plug the USB charging cable to the PA520 and plug the 5V/3A AC-DC adapter to the power jack of the USB charging cable. 2.Place the PA520 into the docking station and plug the 5V/3A AC-DC adapter to the powe…

Text truncated - open the document above for the full version.

CERTIFICATE OF COMPLIANCE Authorized under Declaration of Conformity according to 47 CFR, Part 2 and Part 15 of the FCC Rules. The product listed in follows was (were) tested in the Neutron EMC Laboratory to comply with the criteria limits Class B of conducted and radiated emissions of the Technical Standards FCC Part 15, Subpart B, established by the FCC, USA. Equipment Rugged Mobile Computer Model Name PA520 Brand Name unitech Applicant unitech electronics co., ltd. Address 5F, No. 136, Lane 235, Pao-Chiao Rd., Hsin-Tien Dist., New Taipei City, Taiwan Standard(s) FCC Part 15, Subpart B: 2012 ANSI C63.4: 2009 ICES-003 Issue 5: 2012 CISPR 22: 2008 CAN/CSA-CISPR 22-10 Report(s) NEI-FCCE-1-1312155 The test data, data evaluation, and equipment configuration contained in our test report(s) above was (were) obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of TAF according to the ISO-17025 quality assessment standard and technical standard(s). The test data contained in the referenced test report relate only to the EUT sample and item(s) tested. Andy Chiu Authorized Signatory Neutron Engineering Inc. B1, No. 37, Lane 365, YangGuang St., NeiHu District 114, Taipei, Taiwan. TEL: +886-2-2657-3299 FAX: +886-2-2657-3331

RV-0000000 Project No.: 1312155 Page 2 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 3 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 36 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 37 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 38 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 39 of 39 Neutron Engineering Inc.

RV-0000000 Project No.: 1312155 Page 4 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 5 of 39 Neutron Engineering Inc. 2D Reader RV-0000000 Project No.: 1312155 Page 6 of 39 Neutron Engineering Inc. 2D Reader RV-0000000 Project No.: 1312155 Page 7 of 39 Neutron Engineering Inc. 2D Reader RV-0000000 Project No.: 1312155 Page 8 of 39 Neutron Engineering Inc. 2D Reader RV-0000000 Project No.: 1312155 Page 9 of 39 Neutron Engineering Inc. 1D Reader RV-0000000 Project No.: 1312155 Page 10 of 39 Neutron Engineering Inc. 1D Reader RV-0000000 Project No.: 1312155 Page 11 of 39 Neutron Engineering Inc. 1D Reader RV-0000000 Project No.: 1312155 Page 12 of 39 Neutron Engineering Inc. 1D Reader RV-0000000 Project No.: 1312155 Page 13 of 39 Neutron Engineering Inc. WLAN + Bluetooth Module WLAN Antenna Bluetooth Antenna RFID Module AP Module RV-0000000 Project No.: 1312155 Page 14 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 15 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 16 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 17 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 18 of 39 Neutron Engineering Inc. WLAN + Bluetooth Module

RV-0000000 Project No.: 1312155 Page 19 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 20 of 39 Neutron Engineering Inc. RFID Module RV-0000000 Project No.: 1312155 Page 21 of 39 Neutron Engineering Inc. RFID Module RV-0000000 Project No.: 1312155 Page 22 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 23 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 24 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 25 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 26 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 27 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 28 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 29 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 30 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 31 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 32 of 39 Neutron Engineering Inc. RV-0000000 Project No.: 1312155 Page 33 of 39 Neutron Engineering Inc. RFID Antenna

Report No.: NEI-FCC-SAR-1312155 Page 1 of 89 Neutron Engineering Inc. FCC SAR Test Report FCC ID: HLEPA520BTNF Project No. : 1312155 Equipment : Rugged Mobile Computer Model Name : PA520 Applicant : unitech electronics co., ltd. Address : 5F, No. 136, Lane 235, Pao-Chiao Rd., Hsin-Tien Dist., New Taipei City, Taiwan Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Dec. 23, 2013 Date of Test: Dec. 23, 2013~ Jan. 17, 2014 Date of Issue: Jan. 20, 2014 Testing Engineer : ( Super Jiang) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) Neutron Engineering Inc. No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL: 0769-8318-3000 FAX: 0769-8319-6000 Report No.: NEI-FCC-SAR-1312155 Page 2 of 89 Neutron Engineering Inc. Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML), or National Institute of Standards and Technology (NIST) . Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: NEI-FCC-SAR-1312155 Page 3 of 89 Neutron Engineering Inc. Table of Contents Page 1 . GENERAL SUMMARY 6 2 . RF EMISSIONS MEASUREMENT 7 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 THE MAXIMUM SAR 1G VALUES 9 3.3 LABORATORY ENVIRONMENT 9 3.4 MAIN TEST INSTRUMENTS 10 4 . SAR MEASUREMENTS SYSTEM CONFIGURATION 11 4.1 SAR MEASUREMENT SET-UP 11 4.2 DASY5 E-FIELD PROBE SYSTEM 12 5 . TISSUE-EQUIVALENT LIQUID 19 5.1 TISSUE-EQUIVALENT LIQUID INGREDIENTS 19 5.2 TISSUE-EQUIVALENT LIQUID PROPERTIES 19 6 . SYSTEM CHECK 20 6.1 DESCRIPTION OF SYSTEM CHECK 20 6.2 DESCRIPTION OF SYSTEM CHECK 21 7 . OPERATIONAL CONDITIONS DURING TEST 22 7.1 GENERAL DESCRIPTION OF TEST PROCEDURES 22 7.2 TEST POSITION 22 8 . TEST RESULT 23 8.1 CONDUCTED POWER RESULTS 23 8.2 SAR TEST RESULTS 27 APPENDIX 28 1. TEST LAYOUT 28 2. SYSTEM CHECK RESULTS 29 3. GRAPH RESULTS 32 4. PROBE CALIBRATION CERTIFICATE 53 5. (1) D2450V2 DIPOLE CALIBRATION CERTIFICATE 64 Report No.: NEI-FCC-SAR-1312155 Page 4 of 89 Neutron Engineering Inc. Table of Contents Page 5. (2) D5GHZV2 DIPOLE CALIBRATION CERTIFICATE 72 6. DAE4 CALIBRATION CERTIFICATE 81 7. EUT TESTING POSITION AND ANTENNA LOCATION 86 8. TEST CONFIGURATION 88 Report No.: NEI-FCC-SAR-1312155 Page 5 of 89 Neutron Engineering Inc. REPORT ISSUED HISTORY Issued No. Description Issued Date NEI-FCC-SAR-1312155 Original Issue. Jan. 20, 2014 Report No.: NEI-FCC-SAR-1312155 Page 6 of 89 Neutron Engineering Inc. 1. GENERAL SUMMARY Equipment Rugged Mobile Computer Model Name unitech Brand Name PA520 Model Difference N/A Manufacturer N/A Address N/A Factory N/A Address N/A Standard(s) FCC 47CFR §2.1093 Radio frequency Radiation Exposure Evaluation: Portable Devices ANSI C95.1, 1999 Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.(IEEE Std C95.1-1999) IEEE 1528 2013: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques KDB248227 D01 v01r02 SAR meas for 802 11 a b g v01r02: SAR Measurement Procedures for 802.11a/b/g Transmitters KDB 447498 D02 General RF Exposure Guidance v05r01: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies. KDB 648474 D04 SAR Handsets Multi Xmiter and Ant v01 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCC-SAR-1312155) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of TAF according to the ISO-17025 quality assessment standard and technical standard(s). Report No.: NEI-FCC-SAR-1312155 Page 7 of 89 Neutron Engineering Inc. 2. RF EMISSIONS MEASUREMENT 2.1 TEST FACILITY The test facilities used to collect the test data in this report is SAR room at the location of No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China.523792 2.2 MEASUREMENT UNCERTAINTY Uncertainty Conponent Uncertainty Value Probability Distribution Divisor C i (1g) Standard Uncertainty ±1% V i or V eff Measurement System Probe Calibration (k=1) 5.9 Normal 1 1 5.9 ∞ Axial Isotropy 4.7 Rectangular 3 5.0 1.9 ∞ Hemispherical Isotropy 9.6 Rectangular 3 5.0 3.9 ∞ Boundary Effect 1.0 Rectangular 3 1 0.6 ∞ Linearity 4.7 Rectangular 3 1 2.7 ∞ System Detection Limit 1.0 Rectangular 3 1 0.6 ∞ Readout Electronics 0.3 Normal 1 1 0.3 ∞ Response Time 0.8 Rectangular 3 1 0.5 ∞ Integration Time 2.6 Rectangular 3 1 1.5 ∞ RF Ambient Conditions-Noise 3.0 Rectangular 3 1 1.7 ∞ …

Text truncated - open the document above for the full version.

Report No.: NEI-FCC-SAR-1312155 Page 51 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 52 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 53 of 89 Neutron Engineering Inc. 4. Probe Calibration Certificate EX3DV4 Report No.: NEI-FCC-SAR-1312155 Page 54 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 55 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 56 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 57 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 58 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 59 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 60 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 61 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 62 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 63 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 64 of 89 Neutron Engineering Inc. 5. (1) D2450V2 Dipole Calibration Certificate Report No.: NEI-FCC-SAR-1312155 Page 65 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 66 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 67 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 68 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 69 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 70 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 71 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 72 of 89 Neutron Engineering Inc. 5. (2) D5GHzV2 Dipole Calibration Certificate Report No.: NEI-FCC-SAR-1312155 Page 73 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 74 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 75 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 76 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 77 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 78 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 79 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 80 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 81 of 89 Neutron Engineering Inc. 6. DAE4 Calibration Certificate Report No.: NEI-FCC-SAR-1312155 Page 82 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 83 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 84 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 85 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 86 of 89 Neutron Engineering Inc. 7. EUT Testing Position and antenna location Report No.: NEI-FCC-SAR-1312155 Page 87 of 89 Neutron Engineering Inc. Report No.: NEI-FCC-SAR-1312155 Page 88 of 89 Neutron Engineering Inc. 8. Test Configuration Test Position 1 Test Position 2 Report No.: NEI-FCC-SAR-1312155 Page 89 of 89 Neutron Engineering Inc. Test Position 3 Test Position 4

FCC ID: HLEPA520BTNF RV-0000000 Report No.: NEI-FCCP-3-1312155 Page 1 of 104 Neutron Engineering Inc. FCC Radio Test Report FCC ID: HLEPA520BTNF This report concerns (check one) : Original Grant Class II Change Issued Date : Feb. 11, 2014 Project No. : 1312155 Equipment : Rugged Mobile Computer Model Name : PA520 Applicant : unitech electronics co., ltd. Address : 5F, No. 136, Lane 235, Pao-Chiao Rd., Hsin-Tien Dist., New Taipei City, Taiwan Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Dec. 23, 2013 Date of Test: Dec. 23, 2013 ~ Jan. 22, 2014 Testing Engineer : (Josh Lin) Technical Manager : (Jeff Yang) Authorized Signatory : (Andy Chiu) Neutron Engineering Inc. B1, No. 37, Lane 365, YangGuang St., NeiHu District 114, Taipei, Taiwan. TEL: +886-2-2657-3299 FAX: +886-2-2657-3331 FCC ID: HLEPA520BTNF RV-0000000 Report No.: NEI-FCCP-3-1312155 Page 2 of 104 Neutron Engineering Inc. Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutron shall have no liability for any declarations, inferences or generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. FCC ID: HLEPA520BTNF RV-0000000 Report No.: NEI-FCCP-3-1312155 Page 3 of 104 Neutron Engineering Inc. Table of Contents REPORT ISSUED HISTORY 6 1 CERTIFICATION 7 2 . SUMMARY OF TEST RESULTS 8 2.1 TEST FACILITY 9 2.2 MEASUREMENT UNCERTAINTY 9 3 GENERAL INFORMATION 10 3.1 GENERAL DESCRIPTION OF EUT 10 3.2 DESCRIPTION OF TEST MODES 12 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 13 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 14 3.5 DESCRIPTION OF SUPPORT UNITS 15 4 CONDUCTED EMISSION 16 4.1 LIMIT 16 4.2 MEASUREMENT INSTRUMENTS LIST 16 4.3 TEST PROCEDURES 17 4.4 TEST SETUP LAYOUT 17 4.5 DEVIATION FROM TEST STANDARD 17 4.6 EUT OPERATING CONDITIONS 18 4.7 TEST RESULTS 19 5 ANTENNA CONDUCTED SPURIOUS EMISSION 21 5.1 LIMIT 21 5.2 MEASUREMENT INSTRUMENTS LIST 21 5.3 TEST PROCEDURES 21 5.4 TEST SETUP LAYOUT 21 5.5 DEVIATION FROM TEST STANDARD 21 5.6 EUT OPERATING CONDITIONS 21 5.7 TEST RESULTS 22 6 HOPPING CHANNEL SEPARATION 30 6.1 LIMIT 30 6.2 MEASUREMENT INSTRUMENTS LIST 30 6.3 MEASURING INSTRUMENTS SETTING 30 6.4 TEST PROCEDURES 30 6.5 TEST SETUP LAYOUT 30 6.6 DEVIATION FROM TEST STANDARD 30 6.7 EUT OPERATING CONDITIONS 30 6.8 TEST RESULTS 31 7 MAXIMUM PEAK CONDUCTED OUTPUT POWER 39 7.1 LIMIT 39 FCC ID: HLEPA520BTNF RV-0000000 Report No.: NEI-FCCP-3-1312155 Page 4 of 104 Neutron Engineering Inc. Table of Contents 7.2 MEASUREMENT INSTRUMENTS LIST 39 7.3 TEST PROCEDURES 39 7.4 TEST SETUP LAYOUT 39 7.5 DEVIATION FROM TEST STANDARD 39 7.6 EUT OPERATING CONDITIONS 39 7.7 TEST RESULTS 40 8 RADIATED SPURIOUS EMISSION (9 KHZ TO 1 GHZ) 44 8.1 LIMIT 44 8.2 MEASUREMENT INSTRUMENTS LIST 45 8.3 MEASURING INSTRUMENTS SETTING 45 8.4 TEST PROCEDURES 46 8.5 DEVIATION FROM TEST STANDARD 46 8.6 TEST SETUP LAYOUT 46 8.7 EUT OPERATING CONDITIONS 47 8.8 TEST RESULTS 48 9 RADIATED SPURIOUS EMISSION (ABOVE 1 GHZ) 50 9.1 LIMIT 50 9.2 MEASUREMENT INSTRUMENTS LIST 51 9.3 MEASURING INSTRUMENTS SETTING 51 9.4 TEST PROCEDURES 52 9.5 DEVIATION FROM TEST STANDARD 52 9.6 TEST SETUP LAYOUT 52 9.7 EUT OPERATING CONDITIONS 53 9.8 TEST RESULTS 54 9.9 TEST RESULTS (RESTRICTED BANDS) 78 10 NUMBER OF HOPPING FREQUENCY 86 10.1 LIMIT 86 10.2 MEASUREMENT INSTRUMENTS LIST 86 10.3 MEASURING INSTRUMENTS SETTING 86 10.4 TEST PROCEDURES 86 10.5 TEST SETUP LAYOUT 86 10.6 DEVIATION FROM TEST STANDARD 86 10.7 EUT OPERATING CONDITIONS 86 10.8 TEST RESULTS 87 11 AVERAGE TIME OF OCCUPANCY 89 11.1 LIMIT 89 11.2 MEASUREMENT INSTRUMENTS LIST 89 11.3 TEST PROCEDURES 89 FCC ID: HLEPA520BTNF RV-0000000 Report No.: NEI-FCCP-3-1312155 Page 5 of 104 Neutron Engineering Inc. Table of Contents 11.4 TEST SETUP LAYOUT 89 11.5 DEVIATION FROM TEST STANDARD 89 11.6 EUT OPERATING CONDITIONS 90 11.7 TEST RESULTS 91 12 EUT TEST PHOTO 103 FCC ID: HLEPA520BTNF RV-0000000 Report No.: NEI-FCCP-3-1312155 Page 6 of 104 Neutron Engineering Inc. REPORT ISSUED HISTORY Revised Version No. Description Issued Date - Initial Issue. Feb. 11, 2014 FCC ID: HLEPA520BTNF RV-0000000 Report No.: NEI-FCCP-3-1312155 Page 7 of 104 Neutron Engineering Inc. 1 CERTIFICATION E q u i p m e n t : Rugged Mobile Computer Brand Name : unitech Model Name : PA520 A p p l i c a n t : unitech electronics co., ltd. Date of Test : Dec. 23, 2013 ~ Jan. 22, 2014 Standards : FCC Part 15, Subpart C: 2012 ANSI C63.4: 2009 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-3-1312155) were obtained utilizing the test procedures, test instruments…

Text truncated - open the document above for the full version.

FCC ID: HLEPA520BTNF RV-0000000 Report No.: NEI-FCCP-3-1312155 Page 103 of 104 Neutron Engineering Inc. 12 EUT TEST PHOTO Conducted emission test photos FCC ID: HLEPA520BTNF RV-0000000 Report No.: NEI-FCCP-3-1312155 Page 104 of 104 Neutron Engineering Inc. Radiated spurious emission test photos