HLERM3004PFRM300 4-port UHF RFID Reader Module

Copyright 2012 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd. RM300 2-port / 4-port UHF RFID Reader Module - RM300 - User manual Version 2.5 Preface About This Manual Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice. Regulatory Compliance Statements (1) NCC： 本模組於取得認證後將依規定於模組本體標示審驗合格標籤，並要求最終產品平 台廠商(OEM Integrator)於最終產品平台(End Product)上標示"本產品內含射頻 模組，其 NCC 型式認證號碼為: CCXXxxYYyyyZzW"。 Copyright 2012 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd. Copyright 2012 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd. (2) FCC： This device is intended only for OEM integrators under the following conditions: The use of the External PCB Antenna with gain=3.08 dBi(2.4GHz) IMPORTANT NOTE: In the event that these conditions can’t be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and FCC ID can’t be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product(including the transmitter) and obtain a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID: HLERM3004PF”.The grantee’s FCC ID can be used only when all FCC compliance requirements are met. FCC (U. S. Federal Communications Commission) This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may NOT cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Copyright 2012 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd. Table of Contents Chapter 1 Hardware Overview .................................................................................................................. 1 Introducing the RM300 2-port/4-port UHF RFID Reader Module ............................................ 1 Features .............................................................................................................................. 1 Specifications ...................................................................................................................... 2 Package Content .................................................................................................................... 4 Tour of the RM300 2-port/4-port UHF RFID Reader Module .................................................. 5 Installing the IndyTool ............................................................................................................. 6 Installation Procedure ............................................................................................................. 6 Connecting the RM300 Series to a PC ................................................................................... 7 Chapter 2 IndyTool for Configuration and Development........................................................................ 12 Introduction ............................................................................................................................. 12 Overview ............................................................................................................................. 12 Indy Tool General Usage ........................................................................................................ 12 Info Bar .................................................…

Text truncated - open the document above for the full version.

Report No: WD-RN-R-200328-B0 Page 1 of 5 Attachment 2：EUT Detailed Photographs External Photo (1) EUT Photo (2) EUT Photo Report No: WD-RN-R-200328-B0 Page 2 of 5 External Photo (3) EUT Photo (4) EUT Photo Report No: WD-RN-R-200328-B0 Page 3 of 5 External Photo (5) EUT Photo (6) EUT Photo Report No: WD-RN-R-200328-B0 Page 4 of 5 External Photo (7) EUT Photo (8) EUT Photo Report No: WD-RN-R-200328-B0 Page 5 of 5 External Photo (9) EUT Photo --- END ---

Grantee’s mailing address: [email protected] Tel: +886 2 8912-1122 FCC ID: HLERM3004PF The FCC label will be placed on the device as shown below：

Report No: WD-RF-R-200328-B0 Page 1 of 2 Attachment 2：EUT Detailed Photographs Internal Photo (1) EUT Photo (2) EUT Photo Module Report No: WD-RF-R-200328-B0 Page 2 of 2 Internal Photo (3) EUT Photo --- END ---

Report No: WD-RF-R-200328-C0 Page 1 of 10 FCC MPE Evaluation Report Report No: WD-RF-R-200328-C0 Product Name : RM300 4-port UHF RFID Reader Module Model Name : RM300 FCC ID : HLERM3004PF Applicant : unitech Electronics Co., Ltd. Received Date : Jul. 13, 2020 Tested Date : Jul. 29, 2020 ~ Nov. 06, 2020 Applicable Standard : 47 CFR FCC Part 2.1091 47 CFR FCC Part 1.1310 KDB 447498 D01 OET Bulletin 65 Supplement C Wendell Industrial Co., Ltd Wendell EMC & RF Laboratory Caution: This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. The test results shown in the test report are traceable to the national/international standard through the calibration report of the equipment. Please note that the measurement uncertainty are provided for informational purpose only and are not used in determining the Pass/Fail results. This report must not be used to claim product endorsement by TAF or any agency of the government. The test report shall not be reproduced without the written approval of Wendell Industrial Co., Ltd.. Report No: WD-RF-R-200328-C0 Page 2 of 10 Test Report Issued Date: November 11, 2020 Project No.: 20Q071303 Product Name RM300 4-port UHF RFID Reader Module Trade Name unitech Model Name RM300 FCC ID HLERM3004PF Applicant unitech Electronics Co., Ltd. Manufacturer unitech Electronics Co., Ltd. EUT Rated Voltage DC 5V , 1.5A EUT Test Voltage AC 120V / 60Hz EUT Supports Radios Application 902.75~927.25MHz Applicable Standard 47 CFR FCC Part 2.1091 47 CFR FCC Part 1.1310 KDB 447498 D01 OET Bulletin 65 Supplement C RF Evaluation 0.25219 mW/cm 2 Test Result Complied Documented : ( Specialist / Emma Lu ) Technical Engineer : ( Deputy Section Manager / Jack Chang ) Approved : ( Project Manager / Gary Wu ) Report No: WD-RF-R-200328-C0 Page 3 of 10 Table of Contents Document Revision History ................................................................................................................. 4 Reference Testing Standard ................................................................................................................. 5 1 Generation Information .............................................................................................................. 6 1.1 Applicant .................................................................................................................................... 6 1.2 Manufacturer ............................................................................................................................. 6 1.3 Description of Equipment under Test ...................................................................................... 6 1.4 Test Facility ................................................................................................................................ 7 2 Mobile device Assessment Procedure ......................................................................................... 8 3 RF Exposure Assessment ............................................................................................................. 8 4 Limit Requirement ...................................................................................................................... 9 5 Test Results ................................................................................................................................. 10 Report No: WD-RF-R-200328-C0 Page 4 of 10 Document Revision History Report No. Issue date Description WD-RF-R-200328-C0 November 11, 2020 Initial report Report No: WD-RF-R-200328-C0 Page 5 of 10 Reference Testing Standard Standard Description Version 47 CFR FCC Part 2.1091 Radiofrequency radiation exposure evaluation: mobile devices. -- 47 CFR FCC Part 1.1310 Radiofrequency radiation exposure limits. -- KDB 447498 D01 RF Exposure procedures and equipment authorization policies for mobile and portable devices. V06 OET Bulletin 65 Supplement C Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields. Edition 01-01 Report No: WD-RF-R-200328-C0 Page 6 of 10 1 Generation Information 1.1 Applicant unitech Electronics Co., Ltd. 5F., No. 136, Ln. 235, Baoqiao Rd., Xindian Dist., New Taipei City , Taiwan 1.2 Manufacturer unitech Electronics Co., Ltd. 5F., No. 136, Ln. 235, Baoqiao Rd., Xindian Dist., New Taipei City , Taiwan 1.3 Description of Equipment under Test Product Name RM300 4-port UHF RFID Reader Module Model No. RM300 FCC ID HLERM3004PF Frequency Range 902.75~927.25MHz Number of Channels 50 Type of Modulation FHSS Antenna Information Refer to the table “Antenna List” The above equipment was tested by Wendell EMC & RF Laboratory For compliance with the requirements set forth in 47 CFR § 2.1091 / 47 CFR § 1.1310. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Antenna List No. Manufacturer Model No. Antenna Type Peak Gain 1 CIROCOMM 03A58B0K00J2120 Patch Antenna 3 dBi for 2.4GHz Report No: WD-RF-R-200328-C0 Page 7 of 10 1.4 Test Facility Items Required (IEC 60068-1) Actual Temperature (C) 15-35 25 Humidity (% RH) 25-75 65 Barometric pressure (mbar) 860-1060 1001 Description: Accredited by TAF Accredited Number: 2965 Issued by: Wendell Industrial Co., Ltd Lab Address: 6F/6F-1, No.188, Baoqiao Rd., Xindian Dist., New Taipei City 23145, Taiwan (R.O.C) Test Lab: Wendell EMC & RF Laboratory Test Location: 1F., No. 119, Wugong 3rd Rd., Wugu Dist., New Taipei City 248, Taiwan (R.O.C.) Designation Number: TW0025 Test Firm Registration Number: 665221 Report No: WD-RF-R-200328-C0 Page 8 of 10 2 Mobile device Assessment Procedure In 47 CFR § 2.1…

Text truncated - open the document above for the full version.

Report No: WD-RF-R-200328-B0 Page 1 of 54 FCC Test Report Report No: WD-RF-R-200328-B0 Product Name : RM300 4-port UHF RFID Reader Module Model Name : RM300 FCC ID : HLERM3004PF Applicant : unitech Electronics Co., Ltd. Received Date : Jul. 13, 2020 Tested Date : Jul. 29, 2020 ~ Nov. 13, 2020 Applicable Standard : 47 CFR FCC Part 15, Subpart C (Section 15.247) KDB 558074 D01 DTS Meas. Guidance v05 ANSI C63.10 : 2013 Wendell Industrial Co., Ltd Wendell EMC & RF Laboratory Caution: This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. The test results shown in the test report are traceable to the national/international standard through the calibration report of the equipment. Please note that the measurement uncertainty are provided for informational purpose only and are not used in determining the Pass/Fail results. This report must not be used to claim product endorsement by TAF or any agency of the government. The test report shall not be reproduced without the written approval of Wendell Industrial Co., Ltd.. Report No: WD-RF-R-200328-B0 Page 2 of 54 Test Report Issued Date: November 13, 2020 Project No.: 20Q071303 Product Name RM300 4-port UHF RFID Reader Module Trade Name unitech Model Name RM300 FCC ID HLERM3004PF Applicant unitech Electronics Co., Ltd. Manufacturer unitech Electronics Co., Ltd. EUT Rated Voltage DC 5V , 1.5A EUT Test Voltage AC 120V / 60Hz EUT Supports Radios Application 902.75~927.25MHz Applicable Standard 47 CFR FCC Part 15, Subpart C (Section 15.247) KDB 558074 D01 DTS Meas. Guidance v05 ANSI C63.10 : 2013 Output Power 28.03dBm Test Result Complied Documented : ( Specialist / Emma Lu ) Technical Engineer : ( Deputy Section Manager / Jack Chang ) Approved : ( Project Manager / Gary Wu ) Report No: WD-RF-R-200328-B0 Page 3 of 54 Table of Contents Document Revision History ................................................................................................................. 5 Summary of Test Result ....................................................................................................................... 6 1 Generation Information .............................................................................................................. 7 1.1 Applicant .................................................................................................................................... 7 1.2 Manufacturer ............................................................................................................................. 7 1.3 Description of Equipment under Test ...................................................................................... 7 1.4 Test Mode Applicability And Tested Channel Detail .......................................................... 10 1.5 Configuration of Tested System ............................................................................................. 12 1.6 EUT Exercise Software ........................................................................................................... 12 1.7 Tested System Details .............................................................................................................. 13 1.8 Test Facility .............................................................................................................................. 14 1.9 Measurement Uncertainty ...................................................................................................... 15 1.10 List of Test Equipment ............................................................................................................ 16 2 Test Result .................................................................................................................................. 20 2.1 Antenna Requirement ............................................................................................................. 20 2.1.1 Applicable Standard .......................................................................................................... 20 2.1.2 Antenna Connected Construction ..................................................................................... 20 2.1.3 Antenna Gain .................................................................................................................... 20 2.2 Peak Output Power Measurement ......................................................................................... 21 2.2.1 Limit ................................................................................................................................. 21 2.2.2 Test Setup .......................................................................................................................... 21 2.2.3 Test Procedure................................................................................................................... 21 2.2.4 Test Result ........................................................................................................................ 22 2.3 Number of Hopping Frequency ............................................................................................. 23 2.3.1 Limit ................................................................................................................................. 23 2.3.2 Test Setup .......................................................................................................................... 23 2.3.3 Test Procedure................................................................................................................... 23 2.3.4 Test Result ........................................................................................................................ 24 2.4 Hopping Channel Separation Measurement .........…

Text truncated - open the document above for the full version.

Report No: WD-RF-R-200328-B0 Page 1 of 3 Attachment 1：EUT Test Photographs AC Conducted Emission Report No: WD-RF-R-200328-B0 Page 2 of 3 Radiated Emission for 30 M ~ 1 GHz Report No: WD-RF-R-200328-B0 Page 3 of 3 Radiated Emission for above 1 GHz --- END ---