IDHFEL6Wireless Optical Mouse

FCC statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example-use only shielded interface cables when connecting to computer or peripheral devices). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. and (2) This device must accept any interference received, including interference that may cause undesired operation. This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end its life separately from your household waste. There are sparate collection system for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product. 4. Replace the new batteries Please replace a pair of new batteries and follow the previous instructions. (2, 3) The blue LED on the wheel bar of the mouse is a low batteries power indicator. It indicates that batteries inside the mouse need to be replaced. Note (6) When the battery power is low, the mouse's performance or the trans mission distance may not be good. Please replace the new battery. User's Guide Wireless Optical Mouse Receiver 1. Insert the batteries a. Press the battery cover switch on the bottom of the mouse to open the battery compartment. b. Fit in the batteries accordingly to the diagram indicated in the battery cabinet. c. Close the battery compartments cover properly. d. The Low Power LED on the wheel bar will blink 3 seconds if the mouse power is on. Wheel button Button 5 Button 4 ID reset button Mouse Introduction Congratulations on your purchase of the most innovative wireless optical mouse. With an incredible sensitivity to surface details and high tracking speed than other mice, the mouse can track reliably even on tricky polished or wood-grain surfaces. It offers even more advance that will make you more productive and more comfortable. A. Hardware Installation 2.4GHz RF (distance 6~8m) Using state-of-art technology. High tracking speed and sensitivity. Longer battery life 16 Channels/4096 ID per channels Auto-Link, Plug and Play! No need to set the channel ID. Power on/off button 2*AA Alkaline batteries included 800 dpi Features + - A wrong battery placement may cause batteries overheat. 2 AA batteries Battery compartment cover 2. Connect the receiver a. Turn on your PC. b. Connect the receiver to USB port on PC PC USB port 3. Communication : The mouse The 2.4Ghz RF mouse features a dual-way transmission technology which enables the mouse and the receiver auto-communication. A. Auto-link mode 1. Make sure the Power On-Off Switch on the bottom of the mouse is ON. 2. Operate the mouse, and the LED in the receiver will blink fast. Now the mouse and the receiver is auto-linked successfully. B. Manual mode If you find the communication channel does not connect well, you can use following steps Press ID reset button Red Led indicator blinks faster 1 234 ID links OK! Power on/off button Red LED indicator

Neutron Engineering Inc. Project No.: 1101C112 Page 2 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 2 of 8 1101C112 1101C112

S/N:00000001 FCC ID: IDHFEL6 Wireless Optical Mouse Model: 98904

Neutron Engineering Inc. Project No.: 1101C112 Page 3 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 3 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 4 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 4 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 5 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 5 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 6 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 6 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 7 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 7 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 8 of 8 1101C112 1101C112 Neutron Engineering Inc. Project No.: 1101C112 Page 8 of 8 1101C112 1101C112

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1101C112 Page 2 of 46 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutron shall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FCCP-1-1101C112 Page 3 of 46 Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 10 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 3.4 DESCRIPTION OF SUPPORT UNITS 12 4 . EMC EMISSION TEST 13 4.1 CONDUCTED EMISSION MEASUREMENT 13 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 4.1.2 MEASUREMENT INSTRUMENTS LIST 13 4.1.3 TEST PROCEDURE 14 4.1.4 DEVIATION FROM TEST STANDARD 14 4.1.5 TEST SETUP 14 4.1.6 EUT OPERATING CONDITIONS 14 4.1.7 TEST RESULTS 15 4.2 RADIATED EMISSION MEASUREMENT 16 4.2.1 RADIATED EMISSION LIMITS 16 4.2.2 MEASUREMENT INSTRUMENTS LIST 17 4.2.3 TEST PROCEDURE 20 4.2.4 DEVIATION FROM TEST STANDARD 20 4.2.5 TEST SETUP 21 4.2.6 EUT OPERATING CONDITIONS 21 4.2.7 TEST RESULTS (BETWEEN 30 – 1000 MHz) 22 4.2.8 TEST RESULTS (ABOVE 1000 MHz) 24 4.2.9 TEST RESULTS (2400 – 2483.5 MHz) 36 5 . BANDWIDTH TEST 37 5.1 MEASUREMENT INSTRUMENTS LIST 37 5.2 TEST PROCEDURE 37 5.3 DEVIATION FROM STANDARD 37 5.4 TEST SETUP 37 5.5 EUT OPERATION CONDITIONS 37 5.6 TEST RESULTS 38 6 . ANTENNA CONDUCTED SPURIOUS EMISSION 40 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1101C112 Page 4 of 46 Table of Contents Page 6.1 APPLIED PROCEDURES / LIMIT 40 6.1.1 MEASUREMENT INSTRUMENTS LIST 40 6.1.2 TEST PROCEDURE 40 6.1.3 DEVIATION FROM STANDARD 40 6.1.4 TEST SETUP 40 6.1.5 EUT OPERATION CONDITIONS 40 6.1.6 TEST RESULTS 41 7 . EUT TEST PHOTO 46 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1101C112 Page 5 of 46 1. CERTIFICATION Equipment : Wireless Optical Mouse Brand Name : Fellowes Model Name. : 98904;98912 Applicant : Fellowes, Inc. F a c t o r y : Areson Technology Corporation Address : 11F,NO.646, SEC.5,CHONGSIN RD., SAN CHONG 241, TAIPEI COUNTY , TAIWAN (R.O.C.) Date of Test : Jan. 25, 2011 ~ Jan. 29, 2011 T e s t I t e m : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.249)/ ANSI C63.4 : 2003 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-1-1101C112) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO-17025 quality assessment standard and technical standard(s). Neutron Engineering Inc. Report No.: NEI-FCCP-1-1101C112 Page 6 of 46 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C (15.249) Standard Section Test Item Judgment Remark 15.207 Conducted Emission - Note(1) 15.209 Radiated Emission PASS 15.249 Radiated Spurious Emission PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report (2) The EUT used new battery. Neutron Engineering Inc. Report No.: NEI-FCCP-1-1101C112 Page 7 of 46 2.1 TEST FACILITY The test facilities used to collect the test data in this report is DG-C02/DG-CB03at the location of No.3,Jinshagang 1st Road, ShiXia, Dalang Town,Dong Guan, China.523792 Neutron's test firm number is 319330 2.2 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 A. Conducted Measurement : Test Site Method Measurement Frequency Range U，(dB) NOTE DG-C02 CISPR 150 KHz ~ 30MHz 1.94 B. Radiated Measurement : Test Site Method Measurement Frequency Range Ant. H / V U，(dB) NOTE 30MHz ~ 200MHz V 2.48 30MHz ~ 200MHz H 2.16 200MHz ~ 1,000MHz V 2.50 DG-CB03 CISPR 200MHz ~ 1,000MHz H 2.66 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1101C112 Page 8 of 46 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT Equipment Wireless Optical Mouse Brand Name Fellowes Model Name. 98904;98912 OEM Brand/Model Name N/A Model Difference Only difference is model name. Product Description The EUT is a Wireless Optical Mouse . Product Type Low Power Communication Device Operation Frequency: 2402~2472 MHz Modulation Type: GFSK Date rate: 1Mbps Number of Channel 16CH .Please see note 2. Antenna Designation…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1101C112 Page 46 of 46 7. EUT TEST PHOTO Radiated Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-1101C112 Page 46 of 46 7. EUT TEST PHOTO Radiated Measurement Photos