IGKXT101AIn-Car Beacon

Arbitron Proprietary Information Page 1 of 4 2006 Arbitron Inc MODEL XT101A IN-CAR TRANSMITTER USER’S GUIDE A. IN CAR/OUT OF CAR INDICATOR OVERVIEW Subscribers to Arbitron’s ratings service are not just interested in which radio or television station a panelist listens to, but also where the station was heard - In their home or elsewhere, such as in their car, at work, etc? To meet this need, the PPM system’s In-Car Transmitter incorporates a low power 433 MHz RF transmitter that acts as an “in-car” beacon. If a panelist is in his car with an In-Car Transmitter present, the RF receiver in his personal people meter (PPM) will detect the transmission and log a positive “in Car” event. The PPM records successful detections in its listening log. The In Car/Out of Car Indicator system is illustrated in Figure 1 below. Figure 1: In Car/Out of Car Indicator System PPM In-Car Transmitter Model XT101A In-Car Transmitter User’s Guide Arbitron Proprietary Information Page 2 of 4 2006 Arbitron Inc B. CODE CONFIGURATION The transmitter emits one of four transmission codes based upon two on-board switches. To configure the transmitter: 1) Open the XT101A case by removing the two screws from the case and lifting the cover; 2) Remove and discard the protective film from the switch bank; and 3) Slide the two switch actuators as shown to select the respective PPM RF codes. See Figure 2 below. SW1 Code = 0x638 SW1 Code = 0x71C SW1 Code = 0x0E3 SW1 Code = 0x1C7 SW1 Code = 0x638 SW1SW1 Code = 0x638 SW1 Code = 0x71C SW1 Code = 0x71C SW1 Code = 0x0E3 SW1 Code = 0x0E3 SW1 Code = 0x1C7 SW1 Code = 0x1C7 Figure 2: Transmitter Code Settings Note: The transmitter must be configured prior to battery installation. Model XT101A In-Car Transmitter User’s Guide Arbitron Proprietary Information Page 3 of 4 2006 Arbitron Inc C. BATTERY INSTALLATION Install two lithium 1.5V AAA batteries (e.g., Energizer L92) as shown in Figure 3. Ensure that the batteries are installed with the proper orientation. Note the polarity markings in the battery holder. Replace the cover and reinstall the two screws – Tighten to 2-3 In-Lbs torque maximum. Figure 3: Transmitter Assembly - Exploded View Note: Battery life is approximately 18 months. Model XT101A In-Car Transmitter User’s Guide Arbitron Proprietary Information Page 4 of 4 2006 Arbitron Inc D. IN-CAR TRANSMITTER PLACEMENT Place the transmitter in the vehicle away from metal surfaces. Since the internal antenna is located on the top side of the unit (i.e., the side without screws), this side should be oriented toward the vehicle interior, preferably toward the panelist. Suggested locations are in a front map pocket, overhead storage bin or center console. Do not place the unit in direct sunlight, where driver’s view would be obstructed or where the device would fly free in the event of a sudden stop or accident. E. OPERATING TEMPERATURE RANGE The operating temperature range of the device is -30ºC to +55ºC (-20ºF to +130ºF). NOTICE Changes or modifications not expressly approved by Arbitron could void the user's authority to operate the equipment FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

AR B ITRON t.to E;jij:t' Ronald S. Kolessar Vice President Technology E-mail: ronald.kolessar@arbitron. com r (410) 312-85rs r (410) 312-8604 September 8,2006 Agent's Authorization Letter I, a representative of Arbitron Inc, do hereby authorize, until further notice, Curtis-Straus LLC, of 527 Great Road, Littleto4 MA 01460, to act on our behalf in dealings before the Federal Communications Commission with respect to all matters relating to equipment authorizations under 47 CFR This authorization includes, but is not limitedtq the signing ofForm 731. I certifu that no party (as defined in 47 CFR 1.2002) to this application, including mysel{ is subject to a denial of federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 8534. Certified By: Ronald S. Kolessar Vice President, Technology September 8,2006 Sincerely, rctnnt[5. I(otessar '\lb e gresi[ent, tec fino fogy I Arbitron Inc. r 9705 Patuxent Woods Drive o Columbia l\tD 21046-1572

Company: Arbitron WO: G1366 FCC ID: XT101A IC #: 4213A-XT101A Back of Device Front of Device Company: Arbitron WO: G1366 FCC ID: XT101A IC #: 4213A-XT101A Side of Device Side of Device Company: Arbitron WO: G1366 FCC ID: XT101A IC #: 4213A-XT101A Side of Device Side of Device

Company: Arbitron WO: G1366 FCC ID: XT101A IC #: 4213A-XT101A Label Location

Confidential 10 Kidder Road, Chelmsford, MA, 01824, USA 978-250-4414 Fax: 978-250-1633 www.ils-barcode.com ILS 217L Glossy White Thermal Transfer Imprintable Polyester PRODUCT CONSTRUCTION Facestock:2.0 mil Glossy White Polyester Adhesive: 0.9 mil Permanent Acrylic Liner:3.0 mil 50# paper FEATURES • Facestock resists tearing, abrasion and heat. • Gloss white surface makes label graphics easy to read. • Durable topcoating resists smudging and abrasion when printed with the RB-3000 or RB-8000 ribbons, as well as conventional inks. • Firm acrylic adhesive and has very good adhesion to a variety of surfaces. • UL recognized for indoor and outdoor use. PHYSICAL PROPERTIES (Typical values - not for specification use.) Adhesion: 24 hrs. room temperature Values in oz./in. Surface Expected Range Stainless Steel 32-74 Acrylic 43-75 Glass 28-54 ENVIRONMENTAL PERFORMANCE The properties are based on four-hour immersions at room temperature, unless otherwise noted. Samples were applied to stainless steel 24 hours prior to immersion and were evaluated one hour after removal: ChemicalPerformance Household CleanersVery Good Grease,Oil Very Good Water Very Good Confidential 10 Kidder Road, Chelmsford, MA, 01824, USA 978-250-4414 Fax: 978-250-1633 www.ils-barcode.com ILS 217L Gloss White Thermal Transfer Polyester Service Temperature Range:-40 0 F to +302 0 F (-40 0 C – 150 0 C) Humidity Resistance Very Good After 24 hours at 100 degrees F and 95% relative humidity: No change not ed. Outdoor Life:Outdoor life is approximately 2-5 years. Outdoor aging is dependent on climate, the direction the label faces, the surface angle to which the label is applied (horizontal or vertical), and the amount of airborne pollutants to which the label is exposed. Outdoor life is defined as the length of time the imprinting remains legible . Shelf Life:One year from receipt of material Product should be stored in polyethylene bags at 72 degrees F and 50% relative humidity. SPECIAL CONSIDERATIONS Minimum Application Temperature:50 degrees F. For best bonding conditions, application surface should be at room temperature or slightly higher. For maximum bond strength, surface should be clean and dry. A typical cleaning solvent is heptane or isopropyl alcohol. Higher initial bonds are achieved through increased rub down pressure. All products sold by Industrial Labeling Systems Corp. are governed by our standard warranty and disclaimer of liabilities: Important Notice to Purchaser: All statements, technical information and recommendations herein are based on tests we believe to be reliable, but the accuracy or completeness thereof is not guaranteed, and THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTIES EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PURPOSE: The Seller’s and manufacturer’s only obligation shall be to replace such quantity of product proved to be defective. Before using, user shall determine the suitability of the product for its intended use, and user assumes all risk and liability whatsoever in connection therewith. NEITHER SELLER NOR MANUFACTURER SHALL BE LIABLE EITHER IN TORT OR IN CONTRACT FOR ANY LOSS OR DAMAGE, DIRECT, INCIDENTAL, OR CONSEQUENTIAL (INCLUDING LOSS OF PROFITS OR REVENUE) ARISING OUT OF THE USE OF OR THE INABILITY TO USE THE PRODUCT. No statement or recommendation not contained herein shall have any force or effect unless in agreement signed by officers of seller and manufacturer.

Company: Arbitron WO: G1366 FCC ID: XT101A IC #: 4213A-XT101A Top Side of PCB Company: Arbitron WO: G1366 FCC ID: XT101A IC #: 4213A-XT101A Bottom Side of PCB

Company: Arbitron WO: G1366 FCC ID: XT101A IC #: 4213A-XT101A Top Side of PCB Company: Arbitron WO: G1366 FCC ID: XT101A IC #: 4213A-XT101A Bottom Side of PCB

REPORT: EG1366-1 FCC ID: IGKXT101A IC Code: 4213A-XT101A Curtis-Straus LLC is accredited to ISO/IEC 17025 by A2LA for the specific scope of accreditation under Certificate Number 1627-01. This report may contain data which is not covered by the A2LA accreditation. See our scope of accreditation at the end of this test report. Any opinions or interpretations expressed in this report are outside the scope of our A2LA accreditation as A2LA only accredits testing. _____________________________________________________________ Test Report Report No EG1366-1 Client Arbitron Inc Phone 410-312-8515 Fax 410-312-8604 FRN 0007870256 Models Model XT101A In-Car Transmitter FCC ID IGKXT101A IC # 4213A- XT101A Emissions Designator A1D Equipment Type Low Power Periodic Communications Device Transmitter Equipment Code DXX Results As detailed within this report Curtis-Straus Prepared by Josh LeBlanc – Test Engineer Authorized by Michael Buchholz – EMC Manager Issue Date 4/12/07 Conditions of issue This Test Report is issued subject to the conditions stated in ‘Conditions of Testing’ section of this LLC • 527 Great Road • Littleton, MA • TEL (978) 486-8880 • FAX (978) 486-8828 Page 1 of 16 REPORT: EG1366-1 FCC ID: IGKXT101A IC Code: 4213A-XT101A Curtis-Straus LLC is accredited to ISO/IEC 17025 by A2LA for the specific scope of accreditation under Certificate Number 1627-01. This report may contain data which is not covered by the A2LA accreditation. See our scope of accreditation at the end of this test report. Any opinions or interpretations expressed in this report are outside the scope of our A2LA accreditation as A2LA only accredits testing. _____________________________________________________________ Summary...........................................................................................................3 Test Methodology..............................................................................................3 Statement of Conformity....................................................................................4 EUT Configuration.............................................................................................5 Spurious Radiated Emissions............................................................................6 Emission Bandwidth..........................................................................................7 Fundamental Field Strength and Duty Cycle.....................................................8 Test Equipment Used......................................................................................11 Conditions Of Testing......................................................................................12 A2LA Accreditation..........................................................................................14 LLC • 527 Great Road • Littleton, MA • TEL (978) 486-8880 • FAX (978) 486-8828 Page 2 of 16 Curtis-Straus REPORT: EG1366-1 FCC ID: IGKXT101A IC Code: 4213A-XT101A _____________________________________________________________ Summary This report is an application for certification of a transmitter operating pursuant to 47 CFR and RSS-210 Issue 6. The product covered by this report is the Model XT101A In-Car Transmitter. It has only a transmitter which operates at 433.95MHz. Test Methodology Radiated emissions testing was performed according to the procedures specified in ANSI C63.4 (2003). The EUT was maximized around all three orthogonal axes, as the EUT can only be installed in one position. The EUT has an integrated internal antenna which can not be maximized separately. The standard test voltage was 3Vdc. Fresh batteries were used for testing. The ambient environmental conditions were as follows: Date Temperature Humidity 12/8/06 23.2°C 1008.4mb 12/9/06 23.3°C 1022.7mb Frequency range investigated: 30 MHz- 5GHz Measurement Distance: Frequency (MHz) Distance (m) Comments Fundamental 433.95MHz 3 m Radiated Spurious & harmonics 30 –5000 MHz 3 m Radiated All readings are peak unless otherwise noted. LLC • 527 Great Road • Littleton, MA • TEL (978) 486-8880 • FAX (978) 486-8828 Curtis-Straus REPORT: EG1366-1 FCC ID: IGKXT101A IC Code: 4213A-XT101A _____________________________________________________________ Statement of Conformity The XT101A has been found to conform to the following parts of the 47 CFR, RSS-210, and RSS-GEN as detailed below: RSS-GEN RSS-210 47 CFR Part # Comments 5.3 15.15(b) The product contains no user accessible controls that increase transmission power above allowable levels. 5.2 15.19 The label is shown in the label exhibit. 7.1.5 15.21 Information to the user is shown in the instruction manual exhibit. 15.27 No special accessories are required for compliance. 15.31(e) Equipment was tested with a new battery. 7.1.4 15.203 The device utilizes an integrated antenna printed on the PCB. 7.1.4 15.204 The antenna is not accessible to the user and therefore cannot be easily removed. 2.2 15.205 15.209 The fundamental is not in a restricted band and the spurious emissions in the restricted bands comply with the general emission limits of 15.209. 7.2.2 15.207(b)(2)The EUT is battery powered only. A1.1.1(1) 15.231(a) (1) Product complies with 15.231(e), and A1.1.5 (2) (2) Product complies with 15.231(e), and A1.1.5 (3) (3) Product complies with 15.231(e), and A1.1.5 (4) (4) Product complies with 15.231(e), and A1.1.5 15.231(b) Product complies with 15.231(e). A1.1.3 15.231(c) 20dB bandwidth of the emission is less than 0.25% of the center frequency. A1.1.4 15.231(d) Frequency tolerance is not required, because product does not operate in the specified band. A1.1.5 15.231(e) Fundamental and spurious emissions meet the limits specified in this section. Modifications required for compliance: No modifications were required. LLC • 527 Great Road • Littleton, MA • TEL (978) 486-8880 • FAX (978) 486-8828 Curtis-Straus REPORT: EG1366-1 FCC ID: IGKXT101A IC Code: 4213A-XT101A ___________________________________________________________…

Text truncated - open the document above for the full version.

Company: Arbitron WO: G1366 FCC ID: XT101A IC #: 4213A-XT101A Fundamental and Spurious Radiated Emissions