IR5RT10Notebook Computer

NOTEBOOK COMPUTER RT10 User’s Guide (Preliminary Version) I Notice The company reserves the right to revise this publication or to change its contents without any notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. Any of the software described in this manual is sold or licensed "as is". Should the programs prove defective following purchase, the buyer (and not the manufacturer, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any software defects. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. Copyright© 2015, MilDef Crete Inc. All rights reserved. Trademarks All other brand and product names are trademarks or registered trademarks of their respective companies. II Revision History: Revision D ate Changes Author III FCC (Federal Communications Commission) Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio frequency energy. If not being installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: z Re-orient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. z Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: z This device may not cause harmful interference. z This device must accept any interference received, including interference that may cause undesired operation. z z This radio transmitter FCC ID: IR5RT10 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. z Antenna Information : antenna type: PIFA Antenna gain: -0.36dBi for 2.4GHz / 0.85dBi for 5GHz z 5150 ~5250MHz is for indoor used only. IV FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). V Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Regulatory Information/ Disclaimers Installation and use of this computer must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. VI CE Products with the CE Marking comply with both the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: EN55022 CISPR 22 Radio Frequency Interference EN55024 EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61000-3-2, EN61000-3-3, Generic Immunity Standard LVD EN 60950-1: 2006+ A11: 2009+ A1: 2010+ A12: 2011 IEC 60950-1: 2005+AM1:2009 R&TTE (CE) Manual Regulatory Requirement WLAN - IEEE 802.11a/b/g/n GPS 802.11a/b/g/n Restrictions: European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835 GHz./ 5.150 ~5.250GHz VII CE Declaration of Conformity It is confirmed to comply with the requirements set out in the Council Directive on the approximation of the laws of the member states relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC), the Amendment Directive (93/68/EEC), and the procedures given in European Council Directive (99/5/EC and 2004/108/EC ). The equipment was passed, and the equipment test was performed according to the following European standards: EN 30…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 MilDef Crete Inc. Date : 2015/05/13 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, MilDef Crete Inc. hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product description: Notebook Computer Model Number: RT10 FCC ID: IR5RT10 Sincerely, Signature : Willie Liang / Manager 7F, No. 250, Sec 3, Pei Shen Rd, Shen Keng District,New Taipei TEL: 886-2-2662-6074 #627 FAX: 886-2-2662-6079 MAIL: [email protected]

SCS-F19: Confidentiality Request Letter Page 1 of 3 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 3 Rev 3.0 MilDef Crete Inc. Date: 2015/5/13 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: IR5RT10 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description (Antenna Specification, Software Security Description) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signature : Willie Liang / Manager 7F, No. 250, Sec 3, Pei Shen Rd, Shen Keng District,New Taipei TEL: 886-2-2662-6074 #627 FAX: 886-2-2662-6079 MAIL: [email protected] SCS-F19: Confidentiality Request Letter Page 3 of 3 Rev 3.0 MilDef Crete Inc. Date: 2015/5/13 To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Short Term Confidentiality Request for FCC ID: IR5RT10 To Whom It May Concern: Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 or 180 days (please check one). - User Manual - Internal Photo - External Photo - Test Setup Photo The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Signature : Willie Liang / Manager 7F, No. 250, Sec 3, Pei Shen Rd, Shen Keng District,New Taipei TEL: 886-2-2662-6074 #627 FAX: 886-2-2662-6079 MAIL: [email protected]

MilDef Crete Inc. Date:2015/05/13 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. SIEMIC, INC. 775 Montague Expressway Milpitas, CA 95035 To whom it may concern: I, the undersigned, hereby authorize Murphy Wang, Director of A Test Lab Techno Corp. and hereafter referred to as ATL, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Murphy Wang, Director of A Test Lab Techno Corp. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ATL as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Willie Liang / Manager MilDef Crete Inc. REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

MilDef Crete Inc. 7F, No. 250, Sec 3, Pei Shen Rd, Shen Keng District,New Taipei TEL: 886-2-2662-6074 Ext: 627 FAX: 886-2-2662-6079 Attestation for FCC Declaration of Conformity Brand: MilDef Crete Inc. Model Number: RT10 Date: 2015/05/13 FCC ID: IR5RT10 Please be notified that we, MilDef Crete Inc., would like to declare that the composite portion categorized as computer peripheral has been authorized under the FCC Declaration of Conformity procedures. Testing in regards to this report was done by A Test Lab Techno Corp., located in No.140-1 Changan Str., Bade City Taoyuan County Taiwan, which has been accredited in accordance to all of the requirements of 47 CFR 2.948 (d) and (e) of the FCC rules and KDB349827. Sincerely, Signature : Willie Liang / Manager 7F, No. 250, Sec 3, Pei Shen Rd, Shen Keng District,New Taipei TEL: 886-2-2662-6074 #627 FAX: 886-2-2662-6079 MAIL: [email protected]

1 of 9 External Photos Model Number: RT10 FCC ID: IR5RT10 2 of 9 EUT Photo 1 ) EUT Photo 2 ) Bluetooth/WLAN Antenna WLAN Antenna 3 of 9 EUT Photo 3 ) EUT Photo 4 ) 4 of 9 EUT Photo 5 ) EUT Photo 6 ) 5 of 9 EUT Photo 7 ) EUT Photo 8 ) 6 of 9 EUT Photo 9 ) EUT Photo 10 ) 7 of 9 EUT Photo 11 ) EUT Photo 12 ) 8 of 9 EUT Photo 13 ) EUT Photo 14 ) 9 of 9 EUT Photo 15 )

ID Label info & Label Location FCC ID : IR5RT10

1 of 48 Internal Photos Model Number: RT10 FCC ID: IR5RT10 2 of 48 EUT Photo 1 ) EUT Photo 2 ) 3 of 48 EUT Photo 3 ) EUT Photo 4 ) 4 of 48 EUT Photo 5 ) EUT Photo 6 ) 5 of 48 EUT Photo 7 ) EUT Photo 8 ) 6 of 48 EUT Photo 9 ) EUT Photo 10 ) 7 of 48 EUT Photo 11 ) EUT Photo 12 ) 8 of 48 EUT Photo 13 ) EUT Photo 14 ) 9 of 48 EUT Photo 15 ) EUT Photo 16 ) 10 of 48 EUT Photo 17 ) EUT Photo 18 ) 11 of 48 EUT Photo 19 ) EUT Photo 20 ) 12 of 48 EUT Photo 21 ) EUT Photo 22 ) 13 of 48 EUT Photo 23 ) EUT Photo 24 ) 14 of 48 EUT Photo 25 ) EUT Photo 26 ) 15 of 48 EUT Photo 27 ) EUT Photo 28 ) 16 of 48 EUT Photo 29 ) EUT Photo 30 ) 17 of 48 EUT Photo 31 ) EUT Photo 32 ) 18 of 48 EUT Photo 33 ) EUT Photo 34 ) 19 of 48 EUT Photo 35 ) EUT Photo 36 ) 20 of 48 EUT Photo 37 ) EUT Photo 38 ) 21 of 48 EUT Photo 39 ) EUT Photo 40 ) 22 of 48 EUT Photo 41 ) EUT Photo 42 ) 23 of 48 EUT Photo 43 ) EUT Photo 44 ) 24 of 48 EUT Photo 45 ) EUT Photo 46 ) 25 of 48 EUT Photo 47 ) EUT Photo 48 ) 26 of 48 EUT Photo 49 ) EUT Photo 50 ) 27 of 48 EUT Photo 51 ) EUT Photo 52 ) 28 of 48 EUT Photo 53 ) EUT Photo 54 ) 29 of 48 EUT Photo 55 ) EUT Photo 56 ) 30 of 48 EUT Photo 57 ) EUT Photo 58 ) 31 of 48 EUT Photo 59 ) EUT Photo 60 ) 32 of 48 EUT Photo 61 ) EUT Photo 62 ) 33 of 48 EUT Photo 63 ) EUT Photo 64 ) 34 of 48 EUT Photo 65 ) EUT Photo 66 ) 35 of 48 EUT Photo 67 ) EUT Photo 68 ) 36 of 48 EUT Photo 69 ) EUT Photo 70 ) 37 of 48 EUT Photo 71 ) EUT Photo 72 ) 38 of 48 EUT Photo 73 ) EUT Photo 74 ) 39 of 48 EUT Photo 75 ) EUT Photo 76 ) 40 of 48 EUT Photo 77 ) EUT Photo 78 ) 41 of 48 EUT Photo 79 ) EUT Photo 80 ) 42 of 48 EUT Photo 81 ) EUT Photo 82 ) 43 of 48 EUT Photo 83 ) EUT Photo 84 ) 44 of 48 EUT Photo 85 ) EUT Photo 86 ) 45 of 48 EUT Photo 87 ) EUT Photo 88 ) 46 of 48 EUT Photo 89 ) EUT Photo 90 ) 47 of 48 EUT Photo 91 ) EUT Photo 92 ) 48 of 48 EUT Photo 93 )

FCC RF Test Report Product Type ： Notebook Computer Applicant ： MilDef Crete Inc. Address ： 7F, No. 250, Sec 3, Pei Shen Rd., Shen Keng District,New Taipei City, Taiwan Trade Name ： MilDef Crete Inc. Model Number ： RT10 Test Specification ： FCC 47 CFR PART 15 SUBPART C: Oct., 2014 ANSI C63.10:2009 Receive Date ： Apr. 30, 2015 Test Period ： May 14 ~ 23, 2015 Issue Date ： Jun. 24, 2015 Issue by A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 Taiwan Accreditation Foundation accreditation number: 1330 Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. Report Number: 1506FR17 1 of 54 A Test Lab Techno Corp. Revision History Rev. Issue Date Revisions Revised By 00 Jun. 24, 2015 Initial Issue Report Number: 1506FR17 2 of 54 A Test Lab Techno Corp. Verification of Compliance Issued Date: 06/24/2015 Product Type : Notebook Computer Applicant : MilDef Crete Inc. Address : 7F, No. 250, Sec 3, Pei Shen Rd., Shen Keng District,New Taipei City, Taiwan Trade Name : MilDef Crete Inc. Model Number : RT10 FCC ID : IR5RT10 EUT Rated Voltage : DC 19V, 4.75A Test Voltage : 120 Vac / 60 Hz Applicable Standard : FCC 47 CFR PART 15 SUBPART C: Oct., 2014 ANSI C63.10:2009 Test Result : Complied Performing Lab. : A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 http://www.atl-lab.com.tw/e-index.htm A Test Lab Techno Corp. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by A Test Lab Techno Corp. based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Approved By ： Reviewed By ： (Manager) (Fly Lu) (Testing Engineer) (Eric Ou Yang) Report Number: 1506FR17 3 of 54 A Test Lab Techno Corp. TABLE OF CONTENTS 1 General Information.................................................................................................................................... 6 1.1. Summary of Test Result ...................................................................................................................... 6 1.2. Measurement Uncertainty ................................................................................................................... 6 2 EUT Description .......................................................................................................................................... 7 3 Test Methodology ....................................................................................................................................... 8 3.1. Mode of Operation .............................................................................................................................. 8 3.2. EUT Exercise Software....................................................................................................................... 8 3.3. Configuration of Test System Details .................................................................................................. 9 3.4. Test Site Environment ....................................................................................................................... 10 4 Maximum Conducted Output Power Measurement .............................................................................. 11 4.1. Limit....................................................................................................................................................11 4.2. Test Setup ..........................................................................................................................................11 4.3. Test Instruments .................................................................................................................................11 4.4. Test Procedure ...................................................................................................................................11 4.5. Test Result ........................................................................................................................................ 12 5 Conducted Emission Measurement........................................................................................................ 13 5.1. Limit................................................................................................................................................... 13 5.2. Test Instruments ................................................................................................................................ 13 5.3. Test Setup ......................................................................................................................................... 13 5.4. Test Procedure .................................................................................................................................. 14 5.5. Test Result ........................................................................................................................................ 15 6 Radiated Interference Measurement....................................................................................................... 17 6.1. Limit....................................................................................…

Text truncated - open the document above for the full version.

Part 15C Test Setup Photographs Conducted Emissions Test Configuration: Front View Rear View Report Number: 1506FR17 1 of 3 A Test Lab Techno Corp. Radiated Emissions Test Configuration: Below 1GHz _ Front View Below 1GHz _ Rear View Report Number: 1506FR17 2 of 3 A Test Lab Techno Corp. Above 1GHz _ Front View Above 1GHz _ Rear View Report Number: 1506FR17 3 of 3 A Test Lab Techno Corp.