IXLMODEL240Proximity Reader

GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 Page 1 of 4 Description The GE-Interlogix-CASI Model 240 access control badge reader is an ISO standard compliant, proximity technology badge reader. The Model 240 reader will read ISO-14443 and ISO- 15693 badges and key tags. The reader’s aesthetically pleasing contemporary design and light gray housing will complement any decor. Features: • Compatible with Micro/5 2RP and 8RP controllers (not M/5-2SRP) • Compatible with all Micro/PX(N)-2000 controllers • Sealed electronics, suitable for outdoor installation • Tamper switch protected • Reads ISO-14443 and ISO-15693 access control badges and tags • Reads badge or tag serial number, no memory sector records required • User interface: 3-LEDs and beeper • Fast field maintenance, field wiring plug • Up to 4” read range (badge type and installation conditions dependent) • 4-state input supervision of door contact & REX switch: opened, closed, cut, short • Reader supervision: continuously monitored by the microcontroller Specifications • Mount: on single width USA or European style electrical box or directly on wall • Material: ASA plastic housing; polyurethane encapsulated electronics • Housing dimensions: 3.34 x 4.40 x 0.96 inch: (85 x 112 x 24.2 mm) • Temperature range: -13 to 140 °F /-25 to +70 °C • Power supply: 8VDC to.30 VDC @ <100 mA • Electrical protection: Reverse polarity diode protection on power lines • Data Lines: high-speed transient voltage suppressor diodes • Protection type: IP 65 (IEC 529). Suitable for outdoor installation • Frequency: 13.56 MHz • Approvals: FCC,CE-EN 300 330 • Read distance: up to 2 inches ISO-14443 or up to 4 inches ISO-15693 • Microcontroller firmware versions: Picture Perfect 1.7 or greater recommended • Interface: Supervised F/2F • Electrical connection: 12 position plug-in strip connector with screw terminals • Beeper: controlled by SF2F protocol • Red LED: controlled by SF2F protocol • Green LED: controlled by SF2F protocol • Yellow LED: internal controlled • RS-485 for reader firmware maintenance and configuration • Casi pn: 430177001 GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 Page 2 of 4 FCC Cautionary Comment Modifications to the Model-240 reader not expressly approved by GE-Interlogix may void the FCC approval. Model 240 Back plate Note: Mounting holes fit a standard US single width electrical box and standard European electrical box hole patterns. Installation GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 Page 3 of 4 Installation Considerations 1) Installation of the Model 240 reader on metal The table below shows the expected read range reduction when a Model 240 reader is mounted onto a metal plate or wall. DistanceReading distance No metal plate100 % 1.78 inch (4.5 cm) use 4 Surface Mount Extension plates 100% 1.06 inch, (2.7 cm) use 3 Surface Mount Extension plates 85 % 0.70 inch (1.8 cm) use 2 Surface Mount Extension plates 70 % 0.35 inch (0.9 cm) use 1 Surface Mount Extension plate 50 % Reader placed on metal wall10 % 2) Installation of two Model 240 readers side by side Read range is not affected if the center-to-center distance between two readers is equal to or greater than 6-inches (15 cm). If the distance between the two readers is less than 6-inches (15 cm), field interference between the two readers may result in the creation of a dead spot in the badge read field. Attention Two readers may simultaneously read the same badge or tag if the distance between the two readers is less than 12-inches (30 cm), center-to-center. GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 Page 4 of 4 3) Installation of two Model 240 readers back to back For proper operation, readers installed back-to-back must be separated by at least 3.2 inches (8cm). Attention Two readers may simultaneously read the same badge or tag if the distance between the two readers is less than 6-inches (15 cm), back-to-back. When using two readers back-to-back on a wall that will separate the two readers by 6 inches (15 cm) or less, a metal plate (for example aluminium, 4-inches square (10cm x 10cm) must be placed between the readers. To obtain the maximum read range, mount each Model 240 reader onto one or more Surface Mount Extension plates. Note the impact on badge read range performance, as discussed in manual section, “Installation Considerations” (above). Wiring Reader 12-position field wiring plugMicrocontroller 1 2 3 4 5 6 7 8 9 10 11 12 Micro control, reader beeper (option) Ground Power, 8VDC to 30VDC Door Contact Reader data Exit Request (REX) Green LED Micro control, red LED (option) RS-485-A, reader firmware maintenance RS-485-B, reader firmware maintenance Future Future Micro/5PX(N) 2RP and 8RP, see Micro/5 manual. DO NOT use the Model 240 reader with M/5-S2RP Micro/PX-2000 Micro/PXN-2000 See micro manual Micro/Reader- Junction Box See manual Access Control system compatibility The Model-240 badge reader will output a 16-digit badge identification (BID) number. As a result, the Model-240 reader is only compatible with Picture Perfect access control systems. The Model- 240 reader is not compatible with Secure Perfect, Secure Perfect Enterprise Edition, SP, or SP- Enterprise Edition access control systems, (12-digit BID number limitation). Picture Perfect A 16-digit BID format must be defined within Picture Perfect. Refer to the Picture Perfect On-line help for assistance. In brief, go to Access / Badge Formats. Enter a suitable badge format description, example: “16-digit BID” and define the format: “%16S” (omit the quote characters). Reader to Micro wiring distance The maximum reader to micro cable distance is 1,000 feet (305 meters) from the microcontroller using 4-conductor 22AWG (0.6438mm) shielded cable.

deister electronic GmbH - Hermann-Bahlsen-Straße 11-13 D-30890 Barsinghausen { IDENTIFIKATION PHOENIX TEST-LAB GmbH{ SICHERHEITSTECHNIK Product Certification{ VERKEHRSELEKTRONIK Königswinkel 10 05105-516-01 32825 Blomberg  05105-516217 1. Oktober 2002 RE:Certification Application FCC ID:IXLModel240 Please be advised that the following information is to be held confidential and behalf of deister electronic GmbH, Hermann-Bahlsen-Strasse 11-13, 30890 Barsinghausen, Germany: - circuit diagrams - schematic (component) diagrams - block diagram - technical description of operation The application contains technical information which deister electronic GmbH deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention in this matter. (Stefan Eichler) deister electroinc GmbHHandelsregister :Bankverbindungen :Kto.-Nr.BLZ Hermann-Bahlsen-Straße 11-13Amtsger. Wennigsen HBR 1203Stadtsparkasse Barsinghausen05 304(251 512 70) 30890 BarsinghausenGeschäftsführung:Dresdner Bank Hannover76 142 02(250 800 20) (+49) 05105 516 01Anatoli StobbeDeutsche Bank Barsinghausen4 686 424(250 700 70)  (+49) 05105 516 217USt-IdNr. : DE 115507822Postgiro Hannover612 23-303 (250 100 30) Mitglied . BHE ®

Annex B of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 1 of 1 20646_3.jpg Model 240 (PRA5) front view

Annex C of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 1 of 3 20646_2.jpg Model 240 (PRA5) internal view Annex C of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 2 of 3 20646_1.jpg Model 240 (PRA5) PCB, top view Annex C of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 3 of 3 20646_4.jpg Model 240 (PRA5) PVB, bottom view

Kˆnigswinkel 10 32825 Blomberg Germany Phone +49 5235 9500-0 Fax +49 5235 9500-10 Test Report Reference: R20646 Edition 2 Equipment under Test: Model 240 (PRA5) Serial Number: - FCC ID: IXLMODEL240 Applicant: deister electronic GmbH Manufacturer: deister electronic GmbH Test Laboratory (CAB) accredited by DATech e.V. in compliance with DIN EN ISO/IEC 17025 under the Reg. No. TTI-P-G071/94-11 and listed by FCC 31040/SIT1300F2 TEST REPORT REFERENCE: R20646 Edition 2 Examiner: Thomas K‹HN Date of issue: 27 September 2002 Page 2 of 27 Contents: Page 1 IDENTIFICATION .................................................................................................................................... 3 1.1 APPLICANT .................................................................................................................................... 3 1.2 MANUFACTURER.......................................................................................................................... 3 1.3 DATES............................................................................................................................................ 3 1.4 TEST LABORATORY ..................................................................................................................... 4 1.5 RESERVATION .............................................................................................................................. 4 1.6 NORMATIVE REFERENCES......................................................................................................... 4 1.7 TEST RESULTS ............................................................................................................................. 4 2 TECHNICAL DATA OF EQUIPMENT .....................................................................................................5 2.1 DEVICE UNDER TEST .................................................................................................................. 5 2.2 PEREPHERY DEVICES ................................................................................................................. 5 3 OPERATIONAL STATES AND PHYSICAL BOUNDARIES .................................................................... 6 4 LIST OF TEST MODULES ...................................................................................................................... 7 4.1 EMISSION ...................................................................................................................................... 7 5 METHOD OF MEASUREMENT .............................................................................................................. 8 5.1 RADIATED EMISSIONS 9 kHz TO 30 MHz ................................................................................... 8 5.2 RADIATED EMISSIONS 30 MHz TO 1 GHz .................................................................................. 10 5.3 FREQUENCY STABILITY WITH RESPECT TO AMBIENT TEMPERATURE AND SUPPLY VOLTAGE ............................................................................................................... 12 6 TEST RESULTS EMISSION TEST ......................................................................................................... 14 6.1 PRELIMINARY RADIATED EMISSION TEST (9 kHz to 30 MHz) ................................................. 14 6.2 PRELIMINARY RADIATED EMISSION TEST (30 MHz to 1 GHz) ................................................ 16 6.3 FINAL RADIATED EMISSION TEST (9 kHz to 30 MHz) ............................................................... 18 6.4 FINAL RADIATED EMISSION TEST (30 MHz to 1 GHz)............................................................... 19 6.5 OCCUPIED BANDWIDTH..............................................................................................................21 6.6 FREQUENCY TOLLERANCE ........................................................................................................ 22 7 TEST EQUIPMENT AND ANCILLARIES USED FOR TESTS ................................................................ 23 8 LIST OF ANNEXES ................................................................................................................................. 27 TEST REPORT REFERENCE: R20646 Edition 2 Examiner: Thomas K‹HN Date of issue: 27 September 2002 Page 3 of 27 1 IDENTIFICATION 1.1 APPLICANT Name: deister electronic GmbH Address: Hermann-Bahlsen-Strafle 11 ñ 13 30890 Barsinghausen Country: Germany Name for contact purposes: Mr. Stefan Eichler Phone: +49 51 05 516-129 Fax: +49 51 05 516-266 Mail address: [email protected] Applicant represented during the test by the following person: - 1.2 MANUFACTURER Name: deister electronic GmbH Address: Hermann-Bahlsen-Strafle 11 ñ 13 30890 Barsinghausen Country: Germany Name for contact purposes: Mr. Stefan Eichler Phone: +49 51 05 516-129 Fax: +49 51 05 516-266 Mail address: [email protected] Manufacturer represented during the test by the following person: - 1.3 DATES Date of receipt of test sample: 09 September 2002 Start of test: 17 September 2002 End of test: 25 September 2002 TEST REPORT REFERENCE: R20646 Edition 2 Examiner: Thomas K‹HN Date of issue: 27 September 2002 Page 4 of 27 1.4 TEST LABORATORY The tests were carried out at: PHOENIX TEST-LAB GmbH Kˆnigswinkel 10 D-32825 Blomberg Phone: +49 (0) 52 35 / 95 00-0 Germany Fax: +49 (0) 52 35 / 95 00-10 Test engineer: Thomas K‹HN 27 September 2002 Name Test report checked by: Bernd STEINER 27 September 2002 Name Stamp 1.5 RESERVATION This test report is only valid in its original form. Any reproduction of its contents without written permission of the accredited test laboratory PHOENIX TEST-LAB GmbH is prohibited. The test results herein refer only to the tested sample. PHOENIX TEST-LAB GmbH is not responsible for any generalisations or conclusions drawn from these test results concerning further samples. Any modification of the tested samples is prohibited and leads to the invali…

Text truncated - open the document above for the full version.

Annex A of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 1 of 7 20646_a.jpg test set-up preliminary emission measurement (9 kHz to 30 MHz) Annex A of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 2 of 7 20646_c.jpg test set-up preliminary emission measurement (30 MHz to 1 GHz) Annex A of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 3 of 7 20646_f.jpg test set-up final emission measurement (9 kHz to 30 MHz) Annex A of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 4 of 7 20646_g.jpg test set-up final emission measurement (9 kHz to 30 MHz) Annex A of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 5 of 7 20646_e.jpg test set-up final emission measurement (30 MHz to 1 GHz) Annex A of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 6 of 7 20646_d.jpg test set-up final emission measurement (30 MHz to 1 GHz) Annex A of test report R20646 Edition 2 EUT: Model 240 (PRA5) Manufacturer: deister electronic GmbH Examiner: Thomas K‹HN Date of issue: 27 September 2002 page 7 of 7 20646_h.jpg test set-up climatic chamber