IZP70101-0002Utility Control Network Device

@echelon ® Edge Control Node 7000 Series Installation Guide FIRST REVIEW DRAFT 078-xxxx-01A Echelon, LONWORKS, and the Echelon logo are trademarks of Echelon Corporation registered in the United States and other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Smart Transceivers, Neuron Chips, and other OEM Products were not designed for use in equipment or systems, which involve danger to human health or safety, or a risk of property damage and Echelon assumes no responsibility or liability for use of the Smart Transceivers or Neuron Chips in such applications. Parts manufactured by vendors other than Echelon and referenced in this document have been described for illustrative purposes only, and may not have been tested by Echelon. It is the responsibility of the customer to determine the suitability of these parts for each application. ECHELON MAKES AND YOU RECEIVE NO WARRANTIES OR CONDITIONS, EXPRESS, IMPLIED, STATUTORY OR IN ANY COMMUNICATION WITH YOU, AND ECHELON SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Echelon Corporation. Printed in the United States of America. Copyright © 2010 Echelon Corporation. Echelon Corporation www.echelon.com Edge Control Node 7000 Series Installation Guide iii Welcome To improve both reliability and efficiency, national and regional power distribution grids must become smarter. They must also be able to manage themselves using intelligent distributed control and be able to communicate with any device, over any network or protocol, to optimize grid operations and anticipate problems before they occur. The Echelon ® Edge Control Node (ECN) 7000 Series of open and extensible hardware products enable power distribution grids to become smarter. The ECN 7000 Series distributes the intelligence that public and private electrical power utilities need to monitor and control devices at the edge of the grid. The edge of the grid is the critical point where the distribution network connects to customers and where energy supply and demand are becoming increasingly unpredictable and complex. The ECN 7000 Series is powered by the Echelon Control System (ECoS) software platform, which is part of the Echelon Networked Energy Services (NES) system. ECoS software provides an open, secure, and modular software framework that allows you to host hundreds of new applications that are needed for a smarter grid. This powerful hardware and software combination brings intelligent distributed control to the edge of the grid for maximum reliability, survivability, and responsiveness. This manual describes how a utility worker installs an ECN 7650 device on a utility power pole or a transformer pad. Audience This document assumes that you have a good understanding of medium (<50 kV) and low (<1 kV) power electrical power distribution grids. You should be able to make electrical connections to medium and low power distribution transformers, and be able to make physical connections for electrical devices within the medium and low power electrical distribution grid. You must also understand the safety requirements for working within this environment. Related Documentation The following manuals are available from the Echelon Web site ( www.echelon.com) and provide additional information that can help you deploy Edge Control Node devices and develop applications for them: • Edge Control Node 7000 Series Hardware Guide (078-xxxx-01A). This manual describes the hardware for the ECN. • Edge Control Node 7000 Series Expansion Card Development Guide (078- xxxx-01A). This manual describes the functional requirements for third- party development of expansion cards that plug into the ECN 7000 Series of products. • ECoS User's Guide (078-xxxx-01A). This document describes how to configure the i.LON SmartServer and use its applications to manage control networks. iv • ECoS Power Line Repeating Guide (078-xxxx-01A). This document describes how to manage, control, and monitor a power line repeating network using the SmartServer. • ECoS Vision User’s Guide (078-xxxx-01A). This document describes how to create custom Web pages for monitoring and controlling L ONWORKS ® networks and other control networks. • ECoS App Programming Tools User’s Guide (078-xxxx-01A). This guide describes how to create and use FPMs on your SmartServer, and how to localize the language of the SmartServer Web interface. • Introduction to the LONWORKS Platform (078-0183-01B). This manual provides an introduction to the ISO/IEC 14908-1 (ANSI/CEA-709.1 and EN14908) Control Network Protocol, and provides a high-level introduction to L ONWORKS networks and the tools and components that are used for developing, installing, operating, and maintaining them. All of the Echelon documentation is available in Adobe ® PDF format. To view the PDF files, you must have a current version of the Adobe Reader ® , which you can download from Adobe at: get.adobe.com/reader. FCC Compliance Notice Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules, per sections 15.107 and 15.109. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or tel…

Text truncated - open the document above for the full version.

We the undersigned,herebyauthorizeHeikoStreh~ow,Directorof Regulatoryand AntennaServices(Cetecom,Inc.,411 DixonandingRoad,Milpitas,CA 95035,Te1.408 5866214)to act on our behalfin all mannersrelatihgto applicationfor equipment authorization,includingsigningof all documentsr~latingto thesematters. Any and all acts carriedout by CETECOMInc.,orl our behalfshallhavethe sameeffect as acts of our own. The authorizationfromEcheloncorporatioAis validfor 180 daysfromthe date of this letter. Date:November22, 2010 FederalCommunicationsCommission Authorizationand EvaluationDivision 7435OaklandMillsRoad Columbia.MD 21046 Attn:OETDept. Ref:FCCID: IZP 70101-0002 Applicant:EchelonCorporation DearExaminer, Sincerely, I ,I ~ YaqoobBhimlaI Sr.RegulatoryComplianceEngineer EchelonCorporation 550MeridianA venue SanJose,CA95126 PH:408-938-5353 FAX:408-790-3311 E-mail:ybhimla@eche/on.com =E(HELON~ 550 MeridianAve. San Jose,CA95146 tel: 408 938 5400 fax: 408 790 3800 www.echelon.com

FederalCommunicationCommission EquipmentAuthorizationDivikion,ApplicatioProcessingBranch 7435OaklandMillsRoad Columbia,MD 21048 DATE:November22, 2010 DearFCCExaminer, eECHELON® Pursuantto Paragraphs§0.457and0.459of the Commission'sRules(47 C.F.R.)and Section §552(b)(4)of the Freedomof ¥ormationAct, Echel~nCorporationrequestsconfidentialityfor the followingproducts: FCCID NumberProductTitle/Model IZP70101-0002EdgeControlNode7@00Series/70101 For the productstatedabove,we requestthatIe fOllOlginformationbe heldconfidential: 1) BlockDiagram 2) Schematics 3) PartsList 4) Tune-upprocedure 5) OperationalDescription The aboveexhibitscontainEchelonCorporatin tradesecretsand proprietaryinformationthat couldbe of benefitto our competitorsregardingthe designof our device.Thismaterialis not customarilyavailableto the generalpublicabdwe requestthatit be withheldfrompublic inspection.I If you haveany questions,pleasefeel free to contactme at the addressshownbelow. Sincerely, ~. YaqoobBhimla Sr. RegulatoryComplianceEngineer EchelonCorporation 550MeridianAvenue San Jose,CA 95126 Plf:408-938-5353 FllX:408-790-3311 E-mail:[email protected] 550 MeridianAve. San Jose,CA95q6 tel: 408 938 5~00 fax: 408 790 3800 www.echelon.com

eE(HELON~ FederalCommunicationCommission EquipmentAuthorizationDivision,ApplicationProcessingBranch 7435OaklandMillsRoadI Columbia,MD21048I DATE:November22,2010 DearFCCExaminer, PursuanttoParagraphs§0.457and0.459oftheCommission'sRules(47C.F.R.)andSection I §552(b)(4)oftheFreedom9fInformationf'ct,EchelonCorporationrequeststemporary confidentialityforthefollowingexhibitsfor45dayslfromthedateoftheGrantofEquipment Authorization: FCCIDNumberProduct IZP70101-0002 Title/ModelI EdgeControlNode7000Series/70101 Fortheproductstatedabove,werequestthatthefollowinginformationbeheldconfidential: 1)ExternalPhotos 2)InternalPhotos 3)UsersManual 4)TestSetupPhotos TheaboveexhibitscontainEchelonCorporationtradesecretsandproprietaryinformationthat couldbeofbenefittoourcompetitorsregardingthedesignofourproduct.Tillsmaterialisnot customarilyavailabletothegeneralpublicaAdwerequestthatitbewithheldfrompublic .tiI mspecon. Ifyouhaveanyquestions,pleasefeelfreetocontactmrattheaddressshownbelow. Sincerely, YaqoobBhimla Sr.RegulatoryComplianceEngineer EchelonCorporation 550MeridianAvenue SanJose,CA95126 Plf:408-938-5353 FllX:408-790-3311 E-mail:[email protected] 550MeridianAve. SanJose,CA9512,6 tel:40893852,00 fax:4087903800 www.echelon.com

Top View Bottom View Side View 1 Side View 2 Side View 3 Side View 4

17NOV10 01 17-NOV-10 Top View Notes: - Black lines are for part reference only, not for silkscreen. - Use .eps file format to create silkscreen artwork. ARTWORK, NBOX PRODUCT LABEL 009-0674-01 TW Black Prototype Release 01 TWELLS INITIALSCONTROL # REVISIONS REV. DESCRIPTION DATE TW CUBXXXX Text ink color: Echelon Corporation www.echelon.com Edge Control Node 7000 Series Model No: 70101 Serial No: FCC ID: IZP70101-0002 This device complies with part 15 of the FCC Rules. Operation is subject to the follo wing two conditions; (1) this device may not cause harmful int erference and (2) this device must accept any int erference received, including int erfe rence that may ca use undesi red operation. Rating: Single Phase 3 – wire 120/240, 60 Hz, A= 12

Internal Photos RF Board Internal View-1 Internal View-2 Internal View-3: RF Board Casing Internal View-4: Antenna Connection

FCC-ID IZP70101-0002 PREDICTION OF MPE AT A GIVEN DISTANCE Calculations can be made to predict RF field strength and power density levels around typical RF sources using the general equations (3) and (4) on page 19 of the following FCC document: “OET Bulletin 65, Edition 97-01 - Evaluating Compliance with FCC Guidelines for Human Exposure to Radio frequency Electromagnetic Fields”. These equations are generally accurate in the far field of an antenna but will over predict power density in the near field, where they could be used for making a “worst case” prediction. S = PG/4R 2 (3) Where S = power density (in appropriate units, e.g. mW/cm 2 ) P = power input to the antenna (in appropriate units e.g. mW) G = power gain of the antenna in the direction of interest relative to the isotropic radiator R = distance to the center of radiation of the antenna (appropriate units e.g. cm) or, S = EIRP/4R 2 (4) Where EIRP = Equivalent Isotropically radiated power General Limits: §1.1307 Cellular Radiotelephone Service (subpart H of part 22) Non-building-mounted antennas: height above ground level to lowest point of antenna < 10 m and total power of all channels > 1000 W ERP (1640 W EIRP) §1.1307 Personal Communications Services (part 24) Broadband PCS (subpart E): non-building-mounted antennas: height above ground level to lowest point of antenna < 10 m and total power of all channels > 2000 W ERP (3280 W EIRP) §1.1310 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) (B) Limits for General Population/Uncontrolled Exposure 300–1500 MHz: f/1500 mW/cm² 1500–100,000 MHz: 1.0 mW/cm² §2.1091 No routine evaluation required when the device ...operate at frequencies of 1.5 GHz or below and their effective radiated power (ERP) is 1.5 watts or more, or if they operate at frequencies above 1.5 GHz and their ERP is 3 watts or more. §24.232 (a) Base stations are limited to 1640 watts peak equivalent isotropically radiated power (e.i.r.p.) with an antenna height up to 300 meters HAAT. b) Mobile/portable stations are limited to 2 watts e.i.r.p. peak power. §22.913 (a) Maximum ERP. The effective radiated power (ERP) of base transmitters and cellular repeaters must not exceed 500 Watts. The ERP of mobile transmitters and auxiliary test transmitters must not exceed 7 Watts. FCC-ID IZP70101-0002 The table below is excerpted from Table 1B of 47 CFR 1.1310 titled “Limits for Maximum Permissible Exposure (MPE), Limits for General Population/Uncontrolled Exposure” Frequency Range (MHz) Power Density (mW/cm 2 ) 300 -1500 f/1500 1500 - 100000 1.0 Prediction for Part 22 Maximum radiated power EIRP: 32.9 dBm (1949.8 mW) @ 824.7 MHz Lowest limit for 850 MHz fixed operations (@20cm) where no routine evaluation is required is § 1.1310: (f/1500)mW/cm 2 =0.55 mW/cm 2 Calculated at distance of 20cm for reference antenna: Power density = 1949 / (4 x pi x 20 2 ) = 0.388 mW/cm 2 Result: Configuration complies with rules as power density is below MPE limit. Prediction for Part 24 Maximum radiated power EIRP: 31.45 dBm (1396mW) @1851 MHz Lowest limit for 1900 MHz fixed operations (@20cm) where no routine evaluation is required is § 1.1310: 1 mW/cm 2 Calculated at distance of 20cm: Power density = 1396 / (4 x pi x 20 2 ) = 0.277 mW/cm 2 Result: Configuration complies with rules as power density is below MPE limit. Date: 2010-12-09 Name: Sajay Jose Title: EMC Engineer Company: Cetecom Inc. Address: 411 Dixon Landing Rd, Milpitas, CA 95035, USA Phone: +1 408 586 6249 Email: [email protected]

FCC CFR47 PART 22H AND 24E & INDUSTRY CANADA RSS-132 AND RSS-133 CERTIFICATION TEST REPORT FOR PCA, EVDO MINI-PCI EXPRESS CARD CDMA MODEM MODEL NUMBER: MC5728V FCC ID: N7N-MC5728 IC ID: 2417C-MC5728 REPORT NUMBER: 08U12326-1, Revision B ISSUE DATE: FEBRUARY 23, 2009 Prepared for SIERRA WIRELESS INC 2290 COSMOS COURT CARLSBAD, CA 92009, U.S.A. UNITED STATES Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 08U12326-1B DATE: FEBRUARY 23, 2009 FCC ID: N7N-MC5728 IC: 2417C-MC5728 Page 2 of 63 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By --- 01/29/09 Initial Issue T. Chan B 02/23/09 Added MPE Section T. Chan REPORT NO: 08U12326-1B DATE: FEBRUARY 23, 2009 FCC ID: N7N-MC5728 IC: 2417C-MC5728 Page 3 of 63 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................... 5 2. TEST METHODOLOGY ........................................................................................................ 6 3. FACILITIES AND ACCREDITATION.................................................................................... 6 4. CALIBRATION AND UNCERTAINTY .................................................................................. 6 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................... 6 4.2. MEASUREMENT UNCERTAINTY................................................................................ 6 5. EQUIPMENT UNDER TEST ................................................................................................. 7 5.1. DESCRIPTION OF EUT................................................................................................ 7 5.2. DESCRIPTION OF AVAILABLE ANTENNAS............................................................... 7 6. TEST SUMMARY .................................................................................................................. 7 6.1. LIST OF TEST ITEMS................................................................................................... 7 6.2. MAXIMUM OUTPUT POWER....................................................................................... 7 7. TEST AND MEASUREMENT EQUIPMENT ......................................................................... 8 7.1. DESCRIPTION OF TEST SETUP................................................................................. 9 8. RF POWER OUTPUT VERIFICATION ............................................................................... 12 8.1. RF POWER OUTPUT FOR 1xRTT............................................................................. 12 8.2. RF POWER OUTPUT FOR EVDO REV 0 .................................................................. 15 8.3. RF POWER OUTPUT FOR EVDO REV A.................................................................. 16 9. WORST-CASE CONFIGURATION AND MODE ................................................................ 17 10. CONDUCTED TEST RESULTS ..................................................................................... 18 10.1. OCCUPIED BANDWIDTH........................................................................................... 18 10.2. BAND EDGE ............................................................................................................... 27 10.3. OUT OF BAND EMISSIONS....................................................................................... 32 10.4. FREQUENCY STABILITY........................................................................................... 41 11. RADIATED TEST RESULTS.......................................................................................... 43 11.1. RADIATED POWER (ERP & EIRP) ............................................................................ 43 11.2. FIELD STRENGTH OF SPURIOUS RADIATION ....................................................... 46 11.3. RECEIVER SPURIOUS EMISSIONS ......................................................................... 51 11.4. POWER LINE CONDUCTED EMISSION ................................................................... 55 12. MAXIMUM PERMISSIBLE EXPOSURE ........................................................................ 58 REPORT NO: 08U12326-1B DATE: FEBRUARY 23, 2009 FCC ID: N7N-MC5728 IC: 2417C-MC5728 Page 4 of 63 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 13. SETUP PHOTOS ............................................................................................................ 62 REPORT NO: 08U12326-1B DATE: FEBRUARY 23, 2009 FCC ID: N7N-MC5728 IC: 2417C-MC5728 Page 5 of 63 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: SIERRA WIRELESS INC 2290 COSMOS COURT CARLSBAD, CA. 92009, UNITED STATES. EUT DESCRIPTION: PCA, EVDO MINI-PCI EXPRESS CARD CDMA MODEM MODEL: MC5728V SERIAL NUMBER: P8929580124A2-10 DATE TESTED: JANUARY 14-21, 2009 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 22 H and 24E PASS IC RSS-132 ISSUE 2 and RSS-133 ISSUE 4 PASS Compliance Certification Services, Inc. (CCS) tested the above equipment in accordance with the requirements set forth…

Text truncated - open the document above for the full version.

Bluetooth Qualification Test Facility (BQTF) FCC listed: A2LA Accredited IC recognized # 3462B-1 CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Board of Directors: Dr. Harald Ansorge, Hans Peter May. V3.0 2010-10-30 The BLUETOOTH trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to CETECOM Inc. © Copyright by CETECOM FCC Test Report FOR: Model Name: Edge Control Node 7000 Series Utility Control Network Device FCC ID: IZP70101-0002 47 CFR Part 2, 22, 24 TEST REPORT #: EMC_ECHEL_002_10001_FCC22_24_Rev1 DATE: 2010-12-09 Test Report #: EMC_ECHEL_002_10001_FCC22_24_Rev1 Date of Report: 2010-12-09 Page 2 of 49 Table of Contents 1 Assessment .............................................................................................................................. 3 2 Administrative Data ............................................................................................................... 4 2.1 Identification of the Testing Laboratory Issuing the EMC Test Report ......................................... 4 2.2 Identification of the Client ............................................................................................................. 4 2.3 Identification of the Manufacturer ................................................................................................. 4 3 Equipment under Test (EUT) ............................................................................................... 5 3.1 Specification of the Equipment under Test .................................................................................... 5 3.2 Identification of the Equipment Under Test (EUT) ....................................................................... 6 3.3 Identification of Accessory equipment........................................................................................... 6 4 Subject of Investigation ......................................................................................................... 7 5 Summary of Measurement Results ....................................................................................... 8 6 Measurements ....................................................................................................................... 10 6.1 RF Power Output .......................................................................................................................... 10 6.1.1 References ............................................................................................................................ 10 6.1.2 Measurement requirements: ................................................................................................. 10 6.1.3 Limits: .................................................................................................................................. 10 6.1.4 Radiated Output Power Measurement procedure ................................................................ 11 6.1.5 RF Power Output 850MHz band .......................................................................................... 12 6.1.6 RF Power Output 1900MHz band ........................................................................................ 12 6.1.7 Results .................................................................................................................................. 13 6.2 Spurious Emissions Radiated ....................................................................................................... 17 6.2.1 References ............................................................................................................................ 17 6.2.2 References ............................................................................................................................ 17 6.2.3 Measurement requirements: ................................................................................................. 17 6.2.4 Limits: .................................................................................................................................. 17 6.2.5 Radiated out of band measurement procedure: ................................................................... 18 6.2.6 Radiated out of band emissions results on EUT- Transmit Mode:....................................... 20 6.2.7 Radiated out of band emissions results on EUT- Receive Mode: ........................................ 31 6.2.8 References ............................................................................................................................ 31 6.2.9 Limits .................................................................................................................................... 31 6.2.10 Measurement settings: .......................................................................................................... 31 6.2.11 Results .................................................................................................................................. 31 6.3 AC Power Line Conducted Emissions ......................................................................................... 34 6.3.1 References: ........................................................................................................................... 34 6.3.2 Limits: .................................................................................................................................. 34 6.3.3 Measurement settings: .......................................................................................................... 34 6.3.4 Results .................................................................................................................................. 34 6.3.5 Test Results: .......................................................................................................…

Text truncated - open the document above for the full version.

V2.0 2009-10-30 The BLUETOOTH trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to CETECOM Inc. © Copyright by CETECOM Test Setup Pictures TEST REPORT #: EMC_ECHEL_002_10001_SetupPhotos Test Report #: EMC_ECHEL_002_10001_SetupPhotos Date: 2010-12-03 Page 2 of 5 Radiated Emissions Test Setup Pictures Below 30MHz measurements: 30M-1GHz measurements: Test Report #: EMC_ECHEL_002_10001_SetupPhotos Date: 2010-12-03 Page 3 of 5 >1GHz (Field Strength) measurements: >1GHz (Power) measurements: Test Report #: EMC_ECHEL_002_10001_SetupPhotos Date: 2010-12-03 Page 4 of 5 >18GHz measurements: Test Report #: EMC_ECHEL_002_10001_SetupPhotos Date: 2010-12-03 Page 5 of 5 Conducted Emissions Test Setup Pictures Line Conducted emissions measurement-1 Line Conducted emissions measurement-2