IZP70101-R003Utility Network Telemetry and Control Device

Edge Control Node 7000 Series Hardware and Installation Guide 078-0455-01A Echelon, LONWORKS, Neuron, 3120, and the Echelon logo are trademarks of Echelon Corporation registered in the United States and other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Neuron Chips, Smart Transceivers, and other OEM Products were not designed for use in equipment or systems, which involve danger to human health or safety, or a risk of property damage and Echelon assumes no responsibility or liability for use of the Neuron Chips or Smart Transceivers in such applications. Parts manufactured by vendors other than Echelon and referenced in this document have been described for illustrative purposes only, and may not have been tested by Echelon. It is the responsibility of the customer to determine the suitability of these parts for each application. ECHELON MAKES AND YOU RECEIVE NO WARRANTIES OR CONDITIONS, EXPRESS, IMPLIED, STATUTORY OR IN ANY COMMUNICATION WITH YOU, AND ECHELON SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Echelon Corporation. Printed in the United States of America. Copyright © 2011 Echelon Corporation. Echelon Corporation www.echelon.com ECN 7000 Series Hardware Guide iii Welcome To improve both reliability and efficiency, national and regional power distribution grids must become smarter. They must also be able to manage themselves using intelligent distributed control and be able to communicate with any device, over any network or protocol, to optimize grid operations and anticipate problems before they occur. The Echelon ® Edge Control Node (ECN) 7000 Series of open and extensible hardware products enable power distribution grids to become smarter. The ECN 7000 Series distributes the intelligence that public and private electrical power utilities need to monitor and control devices at the edge of the grid. The edge of the grid is the critical point where the distribution network connects to customers and where energy supply and demand are becoming increasingly unpredictable and complex. The ECN 7000 Series is powered by the Echelon Control Operating System (COS) software platform, which is part of the Echelon Networked Energy Services (NES) system. COS software provides an open, secure, and modular software framework that allows you to host hundreds of new applications that are needed for a smarter grid. This powerful hardware and software combination brings intelligent distributed control to the edge of the grid for maximum reliability, survivability, and responsiveness. This manual describes the hardware within for the ECN 7650 device. It also describes how a utility worker installs an ECN 7650 device on a utility power pole or a transformer pad. Audience This document assumes that you have a good understanding of medium (<50 kV) and low (<1 kV) voltage electrical power distribution grids. You should also understand the communications requirements for your grid applications, and be comfortable working with printed circuit board (PCB) cards. For the installation information, you should be able to make electrical connections to medium and low power distribution transformers, and be able to make physical connections for electrical devices within the medium and low power electrical distribution grid. You must also understand the safety requirements for working within this environment. Related Documentation The following manuals are available from the Echelon Web site (www.echelon.com ) and provide additional information that can help you deploy Edge Control Node devices and develop applications for them: • Edge Control Node 7000 Series Expansion Card Development Guide (078- 0448-01A). This manual describes the functional requirements for third- party development of expansion cards that plug into the ECN 7000 Series of products. • Getting Started with the Edge Control Node (ECN) (078-0452-01A). This document guides you through general activities for the ECN, such as iv connecting the ECN hardware, installing the COS software, configuring an ECN, creating and deploying a custom COS app, creating an ECN component, and deploying that component to multiple ECNs. • COS User's Guide (078-0456-01A). This document describes how to configure the COS software and use its applications to manage grid control networks. • COS App Developer’s Guide (078-0453-01A). This guide describes how to create and use apps on your ECN, and how to localize the language of the COS Web interface. • COS Programmer’s Reference (078-0462-01A). This guide provides the application programming interface (API) reference information for COS app development. All of the Echelon documentation is available in Adobe  PDF format. To view the PDF files, you must have a current version of the Adobe Reader  , which you can download from Adobe at: get.adobe.com/reader . FCC Notice Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules, per sections 15.107 and 15.109. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to…

Text truncated - open the document above for the full version.

Federal Communications Commission Equipment Authorisation Division Application processing Branch 7435 Oakland Mills Road Columbia, MD 21048 June 7 th 2011 Dear FCC Examiner, Pursuant to paragraphs §0.457 and 0.459 of the Commissions Rules (47 C.F.R) and Section §552(b)(4) of the Freedom of Information Act, Echelon Corporation requests confidentiality for the following products FCC ID Number Product Title/Model IZP70101-R000 70101-XXXX Not finalised yet IZP70101-R001 70101-XXXX Not finalised yet IZP70101-R002 70101-XXXX Not finalised yet IZP70101-R003 70101-0021, 70101-0020, 70101-0022, 70101-0023, 70101-0025, For the product stated above, we request that the following information be held confidential: 1) Block diagram 2) Schematics 3) Parts List (BOM Bill of Materials) 4) Tune up procedure 5) Operational Description The above exhibits contain Echelon Corporation trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our device. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, then please feel free to contact me at the address shown below. Sincerely, Stuart H. Bright Regulatory Approvals Manager Echelon Corporation 550 Meridian Avenue San Jose, CA, 95126 PH: 011 44 1923 430100 Fax: 01144 1923 430 300 Email: [email protected]

Description Board Part Number Assembly Number Schematic IZP ‐ 70101 ‐ R000 IZP ‐ 70101 ‐ R001 IZP ‐ 70101 ‐ R002 IZP ‐ 70101 ‐ R003 Mother Board 375 ‐ 1354 801 ‐ 0696 ‐ 51 012 ‐ 1354 ‐ 51 X X X X CPU board 375 ‐ 1353 801 ‐ 0693 ‐ 51 012 ‐ 1353 ‐ 51 X X X X Metering Piggyback board (Option) 375 ‐ 1371 801 ‐ 0716 ‐ 51 012 ‐ 1371 ‐ 51 X X X X AC Distribution 375 ‐ 1370 801 ‐ 0715 ‐ 51 012 ‐ 1370 ‐ 51 X X X X PCBA, NBOX, 2S/12S POWER SUPPLY 375 ‐ 1355 801 ‐ 0697 ‐ 51 012 ‐ 1355 ‐ 51 X X X X MC5728V EV ‐ DO Module 860 ‐ 0416 ‐ 51 (MC5728V) X X EV ‐ DO Interface Board 375 ‐ 1359 801 ‐ 0700 ‐ 51 012 ‐ 1359 ‐ 51 X X DNIP ‐ 350 Wi ‐ Fi AP Option (2.4 and 5.8 GHz 802.11a/an/g/gn) 860 ‐ 0411 ‐ 51 ( D DNIP350 ‐ schematics.pdf X X Wi ‐ Fi Interface Board 375 ‐ 1371 801 ‐ 0732 ‐ 51 012 ‐ 1371 ‐ 51 X X Badger Orion Gateway (900 MHz ISM Band RX) (Option) 65893 ‐ 003 Orion Micro RX XXXX Badger Interface Board (IFB) 375 ‐ 1394 801 ‐ 0751 ‐ 51 012 ‐ 1394 ‐ 51 X X X X RS ‐ 232 Serial Interface (Option) 375 ‐ 1358 801 ‐ 0701 ‐ 51 012 ‐ 1358 ‐ 51 X X X X PLC Band A interface (86 KHz) 375 ‐ 1356 801 ‐ 0698 ‐ 51 012 ‐ 1356 ‐ 51 X X X X PLC Band C interface (132 KHz) (Option) 375 ‐ 1356 801 ‐ 0713 ‐ 51 012 ‐ 1368 ‐ 51 X X X X FCC ID Number Description Board Part Number Assembly Number Schematic Optional Hardware Required IZP ‐ 70101 ‐ 0002 IZP ‐ 70101 ‐ R000 IZP ‐ 70101 ‐ R001 IZP ‐ 70101 ‐ R002 IZP ‐ 70101 ‐ R003 Mother Board 375 ‐ 1354 801 ‐ 0696 ‐ 51 012 ‐ 1354 ‐ 51 XXXXX CPU board 375 ‐ 1353 801 ‐ 0693 ‐ 51 012 ‐ 1353 ‐ 51 XXXXX Metering Piggyback board (Option) 375 ‐ 1371 801 ‐ 0716 ‐ 51 012 ‐ 1371 ‐ 51 (Part of Current Transformer Interface option, and XXXX AC Distribution 375 ‐ 1370 801 ‐ 0715 ‐ 51 012 ‐ 1370 ‐ 51 XXXXX PCBA, NBOX, 2S/12S POWER SUPPLY 375 ‐ 1355 801 ‐ 0697 ‐ 51 012 ‐ 1355 ‐ 51 XXXXX MC5728V EV ‐ DO Module 860 ‐ 0416 ‐ 51 (MC5728V) Requires Badger Interface board X X X EV ‐ DO Interface Board 375 ‐ 1359 801 ‐ 0700 ‐ 51 012 ‐ 1359 ‐ 51 (Part of MC5728V EV ‐ DO option) X X X EV ‐ DO Tri ‐ band Antenna 700/800/900MHz/1.7/1.8/1.9/2.1GHz at antenn a 801 ‐ 0689 ‐ 51 (Part of MC5728V EV ‐ DO option) X X X GPS antenna (Option) GM25 ‐ 1575 ‐ UFL ‐ PASSIVE (Option for MC5728V EV ‐ DO option) X X DNIP ‐ 350 Wi ‐ Fi AP Option (2.4 and 5.8 GHz 802.11a/an / DNIP350 ‐ R 860 ‐ 0411 ‐ 51 (DNIP350 ‐ R) Requires Wi ‐ Fi Interface board,2425 MHz Wi ‐ Fi Antenna, Dual Band Wi ‐ Fi Antenna X X Wi ‐ Fi Interface Board 375 ‐ 1371 801 ‐ 0732 ‐ 51 012 ‐ 1371 ‐ 51 (Part of DNIP350 ‐ R Wi ‐ Fi option) X X 2425 MHz Wi ‐ Fi Antenna at antenna locations 3 and 6 801 ‐ 0775 ‐ 51 (Part of DNIP350 ‐ R Wi ‐ Fi option) X X Dual Band Wi ‐ Fi Antenna at antenna locations 4 and 5 801 ‐ 0688 ‐ 51 (Part of DNIP350 ‐ R Wi ‐ Fi option) X X Badger Orion Gateway (900 MHz ISM Band RX) (Option) 65893 ‐ 003 Requires Badger Interface board X X X X Badger Interface Board (IFB) 375 ‐ 1394 801 ‐ 0751 ‐ 51 012 ‐ 1394 ‐ 51 (Part of Badger Orion Gateway option) X X X X EV ‐ DO Tri ‐ band Antenna 700/800/900MHz/1.7/1.8/1.9/2.1GHz at antenna 801 ‐ 0689 ‐ 51 X X X X RS ‐ 232 Serial Interface (Option) 375 ‐ 1358 801 ‐ 0701 ‐ 51 012 ‐ 1358 ‐ 51 In addition to serial interface board two serial inte r XXXX Ethernet Interface (Option) Requires Ethernet cable assembl y XXXXX Current Transformer Interface (Measures AC power line current) (Option) Requires Metering Piggyback board and current tr a XXXX Galvanicly isolated switch input. (Option) Requires Metering Piggyback board and Switch inp XXXX PLC Band A interface (86 KHz) 375 ‐ 1356 801 ‐ 0698 ‐ 51 012 ‐ 1356 ‐ 51 XXXXX PLC Band C interface (132 KHz) (Option) 375 ‐ 1356 801 ‐ 0713 ‐ 51 012 ‐ 1368 ‐ 51 X X X X Pad Mounted enclosure hardware kit (Shroud over connectors). (Option) X X X X X Their were some antenna changes between IZP ‐ 70101 ‐ 0002 and the current version that improved the bandwidth, but did not significantly effect the gain | FCC ID Number File NameTypeDescription Part of Basic ECN 70101 Option Available for Multiple Radio TX Configurations IZP‐70101‐ R000 IZP‐70101‐ R001 IZP‐70101‐ R002 IZP‐70101‐ R003 Comment 82525 n‐box evdo pattern 8‐2‐10_V2DocN Box EV‐DO Antenna PatternThis is probably obsolete, replaced by "ECN‐7 0| 2111350_MC5728V_Product_Specification_rev1 2PDFMC5728V EV‐DO Module SpecificationXX BLOCK DIAGRAMPDFECN 70101 Series block DiagramXXXXX ECHELON Long term confidentiality agreement_ECN_draftPDF Long term confidentiality agreement for EXXXXX ECN 70101 Schematics 012‐1350‐51A_SchematicPDFDual Band 2425, 5500 MHz Antenna, dual dipole, schematicXX 012‐1351‐51A SCHEMATICPDFEV‐DO Tri Band Antenna 750, 850, 925, 1900 MHz, schematicXX 012‐1353‐5132_SCHEMATICPDFSCHEMATIC, NBOX MAIN PROCESSOR BO AXXXXX 012‐1354‐5126_SCHEMATICPDFSCHEMATIC, NBOX MOTHERBOARDXXXXX 012‐1355‐5130 nbox Power Supply schematicPDFnBOX, Power Supply Board, Front EndXXXXX 012‐1356‐5126_schematicPDFSCHEMATIC, NBOX, A‐BAND PLCXXXXX 012‐1358‐5125_SchematicPDFSCHEMATIC, NBOX SERIAL (RS‐232)XXXXX 012‐1359‐5126_SchematicPDFSchematic, EV‐DO Interface boardXX 012‐1368‐5127_schematicPDFSCHEMATIC, NBOX C‐BAND PLCXXXXX 012‐1370‐5126 SCHEMATICPDFnBOX,MAIN AC DISTRIBUTIONXXXXX 012‐1371‐5127_SchematicPDFSCHEMATIC, NBOX METERING PIGGYBACKXXXXX 012‐1381‐5125_SchematicPDFSCHEMATIC, NBOX, WIFI ADAPTORXX 012‐1409‐5125_SchematicPDFSingle Band 2425 MHz Antenna, with network to increase rejection at 1575 MHz, schematicXX 835‐0774‐51_PCBAsXLSECN 7000 Series PCB BOMsXXXXX Manuals_Specifications Operational DescriptionDOCXECN 7650 Hardware Functional SpecificatiXXXXX Installation GuidePDF Edge Control Node 7000 Series Hardware and Installation Guide ‐Preliminary XXXXX ECN7000series_FTUPDFECN 7000 series data sheetXXXXX Photographs MC5728V_Top5‐IMG_0294JPGXX MC5728V_Bottom5‐IMG_0298JPGXX Internal Photos CDMA ModulePDFXX EV‐DO_Board_Top1‐IMG_0271JPGXX EV‐DO_Board_Bottom1‐IMG_0272JPGXX DNIP350‐Top3‐IMG_0270JPGXX DNIP350‐Bottom1‐IMG_0269JPGXX Badger_Orion‐GW_Top2‐IMG_0277JPGXXXXX Badger_Orion‐GW_Bottom1‐IMG_0278JPGXXXXX Badger_IFB_Top1…

Text truncated - open the document above for the full version.

A B C 123 1234 A B C DIMENSIONS ARE IN MM TOLERANCES UNLESS OTHERWISE SPECIFIED: ANGULAR/BEND: ±0.5° 0.50 - 6.00: ± 0.05 6.01 - 30.00: ± 0.1 30.01 - 120.00: ± 0.2 120.01 - 400.00: ± 0.4 >400.00: ± 0.5 550 Meridian Avenue San Jose, CA 95126 408-938-5200 fax 790-3800 PROPRIETARY AND CONFIDENTIAL This document and the specifications and information contained herein are the exclusive property of Echelon and shall not be copied, reproduced, or disclosed outside of Echelon except as required to execute the terms of a contract or purchase order issued by Echelon. They shall not be included in any proposal or presentation materials without prior written direction of Echelon Corporation. ECHELON Rev 88.00±0.50 178.00±0.50 4X R3.00 DRAWING NO.SHEETREV. 279-0583-51 110 REVDESCRIPTIONINITIALSCONTROL #DATE 10PROTOTYPE RELEASE JLCUB07-JUNE-11 1 of 1 Sheet N/A Finish: SEE NOTES Material: 07-JUNE-11 Date: J. LI Drawn By: M. REICKERD Eng: 10 279-0583-51 Doc. #: LABEL, NBOX IZP70101-R003 Title: NOTES (UNLESS OTHERWISE SPECIFIED): 1. MATERIAL: 3M 7818 SILVER MATTE THERMAL TRANSFER POLYESTER LABEL. 2. THICKNESS: 0.08MM (.0033") WITH 0.02MM (.0008") THICK ADHESIVE. LINER 0.08MM (.0032") 55# DENSIFIED KRAFT. 3. GRAPHICS COLOR: BLACK 4. ALL MATERIALS AND PROCESS MUST BE ROHS COMPLIANT PER EU DIRECTIVE 2002/95/EC. 5. MATERIAL, INCLUDING PRINTING INK, SHALL BE UL APPROVED. 6. CAMERA READY ARTWORK PROVIDED IN .eps FORMAT.

Photograph 1. Badger_IFB_Bottom1-IMG_0280 Photograph 2. Badger_IFB_Top1-IMG_0279 Photograph 3. Badger_Orion-GW_Bottom1-IMG_0278 Photograph 4. Badger_Orion-GW_Top2-IMG_0277 Photograph 5. DNIP350-Bottom1-IMG_0269 Photograph 6. DNIP350-Top3-IMG_0270 Photograph 7. ECN-70101_Case_Removed1-IMG_0288 Photograph 8. ECN-70101_Case_Removed2-IMG_0289 Photograph 9. ECN-70101_Partly Disassembled3-IMG_0283 Photograph 10. ECN-70101_Partly Disassembled5-IMG_0285 Photograph 11. ECN-70101_Partly Disassembled6-IMG_0286 Photograph 12. EV-DO_Board_Bottom1-IMG_0272 Photograph 13. EV-DO_Board_Top1-IMG_0271 Photograph 14. Left Wi-Fi Antennas from Right Side-1-DSCN0053 Photograph 15. MC5728V_Bottom5-IMG_0298 Photograph 16. MC5728V_Top5-IMG_0294 Photograph 17. Prinary EV-DO Antenna-DSCN0054 Photograph 18. Right Badger Antenna-DSCN0055 Photograph 19. Right Wi-Fi Antennas from Right Side-1-DSCN0052 Photograph 20. Wi-Fi Antennas from Right Side-1-DSCN0051 Photograph 21. 375-1353_CPU_Bottom_I0347 Photograph 22. 375-1353_CPU_I0345 Photograph 23. 375-1354_Motherboard_bottom_I0379

Photograph 24. 375-1354_Motherboard_I0382 Photograph 25. 375-1355_Power_Supply_bottom_I0388 Photograph 26. 375-1355_Power_Supply_I0386 Photograph 27. 375-1355_Power_Supply_I0387 Photograph 28. 375-1356_PLC-A_I0393 Photograph 29. 375-1356_PLC-A_I0395 Photograph 30. 375-1356_PLC-C_I0389 Photograph 31. 375-1356_PLC-C_I0392 Photograph 32. 375-1358_Serial_Board_Bottom_I0342 Photograph 33. 375-1358_Serial_Board_I0344 Photograph 34. 375-1359-30_EVDO_IFB_Bottom_I0338 Photograph 35. 375-1359-30_EVDO_IFB_I0335 Photograph 36. 375-1370_AC_Distribution_I0396 Photograph 37. 375-1370_AC_Distribution_I0398 Photograph 38. 375-1371_Metering_piggyback_I0351 Photograph 39. 375-1371_Metering_piggyback_I0352 Photograph 40. 375-1371_WIFI_IFB_bottom_I0400 Photograph 41. 375-1371_WIFI_IFB_I0399 Photograph 42. 375-1394_Badger_IFB_Back_I0356 Photograph 43. 375-1394_Badger_IFB_I0354 Photograph 44. 70101-R00x-Wi-Fi Ant Left-I0329 Photograph 45. 70101-R00x-Wi-Fi Ant Right-I0330 Photograph 46. ECN-70101_Chassy_Empty_0374 Photograph 47. 70101-R003-Top-Shield removed-I0406

N Box antenna pattern – EVDO 8/2/10 1 Plot 1. EVDO @ 850 MHz – elevation, co-polarization, 1-deg resolution run trace AUT MHz dBi gain - elevation max min ave 1 red 1 850 7.5 -39.0 -5.4 4 blue 2 850 6.3 -22.7 -4.1 Note that plot is a “side-view” of the EUT with nose at 0 deg, top-of-head at 90 deg, back-of-head at 180 deg, and neck or bottom of EUT at 270 deg. AUT 1 (red) is proximal to the right-ear, which from the observer’s standpoint is on the left side of the box. 8 -4 -16 -28 -40 0 30 60 90 120 150 180 210 240 270 300 330 N Box antenna pattern – EVDO 8/2/10 2 Plot 2. EVDO @ 850 MHz – azimuth, co-polarization, 1-deg resolution run trace AUT MHz dBi gain - azimuth max min ave 10 red 1 850 7.7 -10.8 -0.5 11 blue 2 850 5.9 -10.5 0.2 Note that plot is a “top-view” of the EUT with nose at 0 deg, left ear at 90 deg, back-of- head at 180 deg, and right ear at 270 deg. AUT 2 (blue) is proximal to the left-ear, which from the observer’s standpoint is on the right side of the box. 8 3 -2 -7 -12 0 30 60 90 120 150 180 210 240 270 300 330 N Box antenna pattern – EVDO 8/2/10 3 Plot 3. EVDO @ 1.9 GHz – elevation, co-polarization, 1-deg resolution run trace AUT GHz dBi gain - elevation max min ave 34 red 1 1.9 2.1 -24.5 -6.6 35 blue 2 1.9 2.3 -33.1 -8.0 Note that plot is a “side-view” of the EUT with nose at 0 deg, top-of-head at 90 deg, back-of-head at 180 deg, and neck or bottom of EUT at 270 deg. AUT 1 (red) is proximal to the right-ear, which from the observer’s standpoint is on the left side of the box. 3 -6.5 -16 -25.5 -35 0 30 60 90 120 150 180 210 240 270 300 330 N Box antenna pattern – EVDO 8/2/10 4 Plot 4. EVDO @ 1.9 GHz – azimuth, co-polarization, 1-deg resolution run trace AUT GHz dBi gain - azimuth max min ave 40 red 1 1.9 4.2 -13.1 -2.0 37 blue 2 1.9 4.0 -10.2 -1.7 Note that plot is a “top-view” of the EUT with nose at 0 deg, left ear at 90 deg, back-of- head at 180 deg, and right ear at 270 deg. AUT 2 (blue) is proximal to the left-ear, which from the observer’s standpoint is on the right side of the box. 5 0 -5 -10 -15 0 30 60 90 120 150 180 210 240 270 300 330

Since EUT has co-located antennas: MPE Limit Calculation: EUT’s operating frequencies @ 824.2 – 849.2 MHz; highest conducted power = ERP – Max Antenna Gain = 23.93 – 11.5 = 12.43dBm (peak) therefore, Limit for Uncontrolled exposure = Freq/1500 = 824.2/1500= 0.549 mW/cm 2 or 5.49 W/m 2 EUT maximum antenna gain = 8.5 dBi + 10log(# of antennas) = 8.5 + 3.0 =11.5dBi Equation from page 18 of OET 65, Edition 97-01 S1 2 or where, S1 = Power Density (Limit = 0.549 mW/cm 2 ) P = Power Input to antenna (17.498mW) G = Antenna Gain (14.125 numeric) R = Minimum Distance between User and Antenna (20 cm) S1 = (17.498*14.125)/(4*3.14*20 2 ) = 247.172/5024 = 0.049 mW/cm 2 S1 < 0.549 mW/cm 2 , MPE Limit Calculation: EUT’s operating frequencies @ 1850-1910 MHz; highest conducted power = EIRP – Antenna Gain = 26.107 – 8.4 = 17.71dBm (peak) therefore, Limit for Uncontrolled exposure: 1 mW/cm 2 or 10 W/m 2 EUT maximum antenna gain = 5.4 dBi + 10log(# of antennas) = 5.4 + 3.0 = 8.4dBi Equation from page 18 of OET 65, Edition 97-01 S2 2 or where, S2 = Power Density (Limit = 1 mW/cm 2 ) P = Power Input to antenna (59.020mW) G = Antenna Gain (6.918 numeric) R = Minimum Distance between User and Antenna (20 cm) S2 = (59.020*6.918)/(4*3.14*20 2 ) = 408.319/5024 = 0.082 mW/cm 2 S2 < 1 mW/cm 2 , MPE Limit Calculation: EUT’s operating frequencies @ 2400-2483.5 MHz; highest conducted power = 28.86dBm (peak) therefore, Limit for Uncontrolled exposure: 1 mW/cm 2 or 10 W/m 2 EUT maximum antenna gain = 4.3dBi + 10log(# of antennas) = 4.3 + 3.0 = 7.3dBi Equation from page 18 of OET 65, Edition 97-01 S3 2 or where, S3 = Power Density (Limit = 1 mW/cm 2 ) P = Power Input to antenna (770.96mW) G = Antenna Gain (5.383 numeric) R = Minimum Distance between User and Antenna (20 cm) S3 = (770.96*5.383)/(4*3.14*20 2 ) = 4150.08/5024 = 0.826 mW/cm 2 S3 < 1 mW/cm 2 MPE Limit Calculation: EUT’s operating frequencies @ 5725-5850 MHz; highest conducted power = 28.915dBm (peak) therefore, Limit for Uncontrolled exposure: 1 mW/cm 2 or 10 W/m 2 EUT maximum antenna gain = 4 dBi + 10log(# of antennas) = 4.0 + 3.0 = 7.0dBi. Equation from page 18 of OET 65, Edition 97-01 S4 2 or where, S4 = Power Density (Limit = 1 mW/cm 2 ) P = Power Input to antenna (780.78mW) G = Antenna Gain (5.024 numeric) R = Minimum Distance between User and Antenna (20 cm) S4 = (780.78*5.024)/(4*3.14*20 2 ) = 3922.64/5024 = 0.781 mW/cm 2 S4 < 1 mW/cm 2 For Co-located Antennas: S1 + S2 + S3 + S4 < 1mW/cm2 Since, 0.049 mW/cm2 + 0.082 mW/cm2 + 0.826 mW/cm2 + 0.781 mW/cm2 > 1 mW/cm2 The Minimum Distance between User and Antennas is R = (√P1G1 / (4*3.14*0.549)) + (√(P2G2 + P3G3 + P4G4) / (4*3.14*1)) = (√247.17/3.79) + ((408.32 + 4130.48 + 3903.91)/ 12.56) = 27.15 cm

MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE ! BALTIMORE, MARYLAND 21230-3432 ! PHONE (410) 354-3300 ! FAX (410) 354-3313 33439 WESTERN AVENUE ● UNION CITY, CALIFORNIA 94587 ● PHONE (510) 489-6300 ● FAX (510) 489-6372 3162 BELICK STREET ● SANTA CLARA, CALIFORNIA 95054 ● PHONE (408 748-3585 ● FAX (510) 489-6372 The Nation’s First Licensed Nationally Recognized Testing Laboratory June 27, 2011 Echelon Corporation 550 Meridian Avenue San Jose, CA 95126 Dear James Smith, Enclosed is the EMC Wireless test report for compliance testing of the Echelon Corporation, Edge Control Node (ECN) 70101-0026 as tested to the requirements of the FCC Certification rules under Title 47 of the CFR Part 22 Subpart H and RSS-132, Issue 2, September 2005 for Cellular Devices, Part 24 Subpart E and RSS-133, Issue 5, February 2009 for Broadband PCS Devices. Thank you for using the services of MET Laboratories, Inc. If you have any questions regarding these results or if MET can be of further service to you, please contact me. Sincerely yours, MET LABORATORIES, INC. Jennifer Warnell Documentation Department Reference: (\Echelon Corporation\EMCS31779-FCC22/24 Rev. 1) Certificates and reports shall not be reproduced except in full, without the written permission of MET Laboratories, Inc. MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE ! BALTIMORE, MARYLAND 21230-3432 ! PHONE (410) 354-3300 ! FAX (410) 354-3313 33439 WESTERN AVENUE ● UNION CITY, CALIFORNIA 94587 ● PHONE (510) 489-6300 ● FAX (510) 489-6372 3162 BELICK STREET ● SANTA CLARA, CALIFORNIA 95054 ● PHONE (408 748-3585 ● FAX (510) 489-6372 MET Report: EMC29556-FCC22/24/27 © 2011, MET Laboratories, Inc. Page ii of vii Electromagnetic Compatibility Criteria Test Report for the Echelon Corporation Model Edge Control Node (ECN) 70101-0026 Tested under FCC Certification Rules Title 47 of the CFR, Part 22 Subpart H & RSS-132, Issue 2, September 2005 for Cellular Devices, Part 24 Subpart E & RSS-133, Issue 5, February 2009 for Broadband PCS Devices MET Report: EMCS31779-FCC22/24 Rev. 1 June 27, 2011 Prepared For: Echelon Corporation 550 Meridian Avenue San Jose, CA 95126 Prepared By: MET Laboratories, Inc. 914 W. Patapsco Ave Baltimore, MD 21230 Electromagnetic Compatibility Echelon Corporation Cover Page Edge Control Node (ECN) 70101-0026 CFR Title 47 Part 22 H & RSS-132; Part 24 E & RSS-133 MET Report: EMCS31779-FCC22/24 Rev. 1 © 2011, MET Laboratories, Inc. Page iii of xviii Electromagnetic Compatibility Criteria Test Report for the Echelon Corporation Model Edge Control Node (ECN) 70101-0026 Tested Under FCC Certification Rules Title 47 of the CFR, Part 22 Subpart H & RSS-132, Issue 2, September 2005 for Cellular Devices, Part 24 Subpart E & RSS-133, Issue 5, February 2009 for Broadband PCS Devices Lionel Gabrillo, Project Engineer Jennifer Warnell Electromagnetic Compatibility Lab Documentation Department Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of Part 22 Subpart H, Part 24 Subpart E of the FCC Rules and Industry Canada standards RSS-132, Issue 2, September 2005 and RSS-133, Issue 5, February 2009 under normal use and maintenance. Shawn McMillen, Wireless Manager Electromagnetic Compatibility Lab Electromagnetic Compatibility Echelon Corporation Report Status Edge Control Node (ECN) 70101-0026 C CFR Title 47 Part 22 H & RSS-132; Part 24 E & RSS-133 MET Report: EMCS31779-FCC22/24 Rev. 1 © 2011, MET Laboratories, Inc. Page iv of xviii Report Status Sheet Revision Report Date Reason for Revision  June 21, 2011 Initial Issue. 1 June 27, 2011 Revised to reflect engineer corrections. Electromagnetic Compatibility Echelon Corporation Table of Contents Edge Control Node (ECN) 70101-0026 CFR Title 47 Part 22 H & RSS-132; Part 24 E & RSS-133 MET Report: EMCS31779-FCC22/24 Rev. 1 © 2011, MET Laboratories, Inc. Page v of vii Table of Contents I. Executive Summary ................................................................................................................................................. 1 A. Purpose of Test ................................................................................................................................................... 2 B. Executive Summary ............................................................................................................................................ 2 II. Equipment Configuration ....................................................................................................................................... 3 A. Overview ............................................................................................................................................................. 4 B. References ........................................................................................................................................................... 5 C. Test Site .............................................................................................................................................................. 5 D. Description of Test Sample ................................................................................................................................. 6 E. Equipment Configuration .................................................................................................................................... 8 F. Support Equipment ...............................................................…

Text truncated - open the document above for the full version.

FCC CFR47 PART 22H AND 24E & INDUSTRY CANADA RSS-132 AND RSS-133 CERTIFICATION TEST REPORT FOR PCA, EVDO MINI-PCI EXPRESS CARD CDMA MODEM MODEL NUMBER: MC5728V FCC ID: N7N-MC5728 IC ID: 2417C-MC5728 REPORT NUMBER: 08U12326-1, Revision C ISSUE DATE: JANUARY 16, 2011 Prepared for SIERRA WIRELESS INC 2290 COSMOS COURT CARLSBAD, CA 92009, U.S.A. UNITED STATES Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 08U12326-1C DATE: JANUARY 16, 2011 FCC ID: N7N-MC5728 IC: 2417C-MC5728 Page 2 of 62 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By --- 01/29/09 Initial Issue T. Chan B 02/23/09 Added MPE Section T. Chan C 01/16/11 Updated MPE Section with Average Powers T. Chan REPORT NO: 08U12326-1C DATE: JANUARY 16, 2011 FCC ID: N7N-MC5728 IC: 2417C-MC5728 Page 3 of 62 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................... 5 2. TEST METHODOLOGY ........................................................................................................ 6 3. FACILITIES AND ACCREDITATION.................................................................................... 6 4. CALIBRATION AND UNCERTAINTY .................................................................................. 6 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................... 6 4.2. MEASUREMENT UNCERTAINTY................................................................................ 6 5. EQUIPMENT UNDER TEST ................................................................................................. 7 5.1. DESCRIPTION OF EUT.................................................…

Text truncated - open the document above for the full version.