JNF-BRC-RS90Bluetooth communication cradle

Advanced Handheld High-Speed Laser Scanner 1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. 15.105 Federal Communications Commission (FCC) Requirements, Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver. ---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ---Consult the dealer or an experienced radio/TV technician for help. Wireless Handheld Gun Type Scanner i USER’S MANUAL User’s Manual Z-3190BT, Z-3191BT, Z3192BT Wireless Barcode Scanner CR-90, RS-90 Charging & RF Communication Station Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0 August. 24, 2011 Initial release 1.1 March. 26, 2012 Added wireless communication tips 1.2 April. 18, 2012 Added cable clip installation and Smart Phone Software Keypad Control Setting 1.3 May. 24, 2012 Added pin-out configuration and cable pin-out 1.4 June. 1 2012 Removed the charging cradle section Wireless Handheld Gun Type Scanner ii USER’S MANUAL Important Notice No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or fitness for any particular purpose. We are not liable for any errors contained herein nor for incidental or consequential damages in connection with furnishing, performance or use of this material. We shall be under no liability in respect of any defect arising from fair wear and tear, willful damage, negligence, abnormal working conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of the products without written approval. No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed, or translated into any human or computer or other language in any form or by any means electronic, mechanical, magnetic, optical, chemical, biological, manual or otherwise, except for brief passages which may be quoted for purposes of scholastic or literary review, without express written consent and authorization. We reserve the right to make changes in product design without reservation and without notification. The material in this guide is for information only and is subject to change without notice. All trademarks mentioned herein, registered or otherwise, are the properties of their various, ill, assorted owners. General Handling Precautions Do not dispose the scanner in fire. Do not put the scanner directly in the sun or by any heat source. Do not use or store the scanner in a very humid place. Do not drop the scanner or allow it to collide violently with other objects. Do not take the scanner apart without authorization Guidance for Printing This manual is in A5 size. Please double check your printer setting before printing it out. When the barcodes are to be printed out for programming, the use of a high-resolution laser printer is strongly suggested for the best scan result. Copyright © 2012. All rights reserved. USER’S MANUAL Radio Notice This equipment generates uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions in this manual, it may cause interference to radio communications. The equipment has been tested and found to comply with the limits for a Class B computing device pursuant to EN55022 and 47 CFR, Part 2 and Part 15 of the FCC rules. These specifications are designed to provide reasonable protection against interference when operated in a commercial environment. Radio and Television Interference Operation of this equipment in a residential area can cause interference to radio or television reception. This can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures: - Reorient the receiving antenna. - Relocate the device with respect to the receiver. - Move the device away from the receiver. - Plug the device into a different outlet so that the device and the receiver are on different branch circuits. If necessary the user may consult the manufacturer, and authorized dealer, or experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, DC 20402 U.S.A., Stock No. 04000003454. 0 Laser Safety This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions in this manual, it may cause interference to radio communications. The equipment has been tested and found to comply with the limits for a Class B computing device pursuant to EN55022 and 47 CFR, Part 2 and Part 15 of FCC Rules. These specifications are designed to provide reasonable protection against interfe…

Text truncated - open the document above for the full version.

Report No.：T120419D02 Page 1 of 14 External Photo Report No.：T120419D02 Page 2 of 14 Report No.：T120419D02 Page 3 of 14 Power Adapter Photo (Model : PA1005-1Sl) Report No.：T120419D02 Page 4 of 14

Report No.T120419D02 Page 5 of 13 Internal Photo Report No.T120419D02 Page 6 of 13 Report No.T120419D02 Page 7 of 13 Report No.T120419D02 Page 8 of 13 Report No.T120419D02 Page 9 of 13 Report No.T120419D02 Page 10 of 13 Report No.T120419D02 Page 11 of 13 Report No.T120419D02 Page 12 of 13 Antenna Photo Report No.T120419D02 Page 13 of 13

FCC ID：JNF-BRC-RS90 Report No.：T120419D02-RP1 Page 1 / 80 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. FCC 47 CFR PART 15 SUBPART C AND ANSI C63.4:2003 TEST REPORT For BT wireless communication cradle Model : RS-90 Trade Name : ZEBEX Issued for ZEBEX INDUSTRIES INC. B1F.-1, No. 207, Sec. 3, Beixin Rd, Xindian Dist, New Taipei City 23143, Taiwan Issued by Compliance Certification Services Inc. Hsinchu Lab. NO. 989-1 Wen Shan Rd., Shang Shan Village, Qionglin Shiang Hsinchu County 30741, Taiwan, R.O.C TEL: +886-3-5921698 FAX: +886-3-5921108 http://www.ccsrf.com E-Mail : [email protected] Issued Date: May 10, 2012 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF or any government agencies. The test results of this report relate only to the tested sample identified in this report. FCC ID：JNF-BRC-RS90 Report No.：T120419D02-RP1 Page 2 / 80 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. Revision History Rev. Issue Date Revisions Effect Page Revised By 00 05/10/2012 Initial Issue All Page 80 Kelly Tsai FCC ID：JNF-BRC-RS90 Report No.：T120419D02-RP1 Page 3 / 80 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. TABLE OF CONTENTS TITLE PAGE NO. 1. TEST REPORT CERTIFICATION ................................................................................ 4 2. EUT DESCRIPTION ..................................................................................................... 5 3. DESCRIPTION OF TEST MODES ............................................................................... 6 4. TEST METHODOLOGY ............................................................................................... 7 5. FACILITIES AND ACCREDITATION ........................................................................... 8 5.1 FACILITIES ............................................................................................................ 8 5.2 ACCREDITATIONS................................................................................................ 8 5.3 MEASUREMENT UNCERTAINTY ......................................................................... 9 6. SETUP OF EQUIPMENT UNDER TEST...................................................................... 10-11 7. FCC PART 15.247 REQUIREMENTS.......................................................................... 12 7.1 DUTY CYCLE CORRECTION FACTOR ................................................................ 12 7.2 20dB BANDWIDTH FOR HOPPING...................................................................... 13-18 7.3 MAXIMUM PEAK OUTPUT POWER..................................................................... 19-20 7.4 HOPPING CHANNEL SEPARATION..................................................................... 21-26 7.5 NUMBER OF HOPPING FREQUENCY USED ...................................................... 27-29 7.6 DWELL TIME ON EACH CHANNEL ...................................................................... 30-44 7.7 CONDUCTED SPURIOUS EMISSION .................................................................. 45-52 7.8 RADIATED EMISSION........................................................................................... 53-71 7.9 CONDUCTED EMISSION ...................................................................................... 72-76 APPENDIX SETUP PHOTOS .......................................................................................... 77-80 FCC ID：JNF-BRC-RS90 Report No.：T120419D02-RP1 Page 4 / 80 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. 1. TEST REPORT CERTIFICATION Applicant ： ZEBEX INDUSTRIES INC. Address ： B1F.-1, No. 207, Sec. 3, Beixin Rd, Xindian Dist, New Taipei City 23143, Taiwan Equipment Under Test ： BT wireless communication cradle Model ： RS-90 Trade Name ： ZEBEX Tested Date ： April 19 ~ May 08, 2012 APPLICABLE STANDARD Standard Test Result FCC Part 15 Subpart C AND ANSI C63.4:2003 PASS WE HEREBY CERTIFY THAT: The above equipment has been tested by Compliance Certification Services Inc., and found compliance with the requirements set forth in the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Approved by: Reviewed by: Sb Lu Gundam Lin Sr. Engineer Sr. Engineer FCC ID：JNF-BRC-RS90 Report No.：T120419D02-RP1 Page 5 / 80 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. 2. EUT DESCRIPTION Product Name BT wireless communication cradle Model Number RS-90 Identify Number T120419D02 Received Date April 19, 2012 Frequency Range 2402MHz to 2480MHz f = 2402 + nMHz, n = 0, .....78 Transmit Power 10.98 dBm (0.0125W) Channel Spacing 1MHz Channel Number 79 Channels Transmit Data Rate GFSK (1Mbps), /4-DQPSK (2Mbps), 8-DPSK (3Mbps) Type of Modulation Frequency Hopping Spread Spectrum Frequency Selection by software / firmware Antenna Type PIFA Antenna, Antenna Gain : 2dBi Power Rating 5Vdc RF Exposure Evaluation Since the EUT is classed portable device, and the maximum peak power is 10.98 dBm (<13.6dBm), the MPE evaluation is not required and no SAR consideration applied. DC Power Cord Type Shielded mini USB cable, 1.4m (detachable) with a core I/O Port RJ-45 Port × 1, Mini USB Port × 1 No. Signal Cable Description 1 LAN to RS232 Cable: S…

Text truncated - open the document above for the full version.

FCC ID：JNF-BRC-RS90 Report No.：T120419D02-RP1 Page 77 / 80 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. APPENDIX SETUP PHOTOS RADIATED EMISSION SETUP FCC ID：JNF-BRC-RS90 Report No.：T120419D02-RP1 Page 78 / 80 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. FCC ID：JNF-BRC-RS90 Report No.：T120419D02-RP1 Page 79 / 80 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP FCC ID：JNF-BRC-RS90 Report No.：T120419D02-RP1 Page 80 / 80 This report shall not be reproduced, except in full, without the written approval of Compliance Certification Services Inc. CONDUCTED EMISSION SETUP