KBCIX250RIM902Rugged Laptop PC with RIM 902 Mobitex Radio Modem

77-0100-001 12 September 2000 GoBook™ User’s Manual ii Identification GoBook (IX250) User’s Manual September 2000 · Revision 001 Copyright Notice © Copyright 2000 Itronix Corporation. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any other language or computer language in whole or in part, in any form or by any means, whether it be electronic, mechanical, magnetic, optical, manual, or otherwise, without the prior written consent of Itronix Corporation, South 801 Stevens Street, Spokane, Washington 99204. Disclaimer This document is printed in the U.S.A. Itronix Corporation reserves the right to revise the manual and make periodic changes to the content without a direct or inferred obligation to Itronix to notify any person of such revision or changes. Itronix Corporation does not assume responsibility for the use of this manual, nor for any patent infringements or other rights or third parties who may use the manual. This document contains valuable trade secrets and proprietary information of Itronix Corporation. This product is available for purchase under the terms of the Itronix Hardware Purchase and Software License Agreement. Itronix hardware products may be reconditioned, or be manufactured from parts and components that may be new, used, rebuilt, or recycled and in some cases, the hardware product may not be new and may have been previously installed. In any event, Itronix warranty terms apply. Trademark Notice Itronix is a registered trademark of Itronix Corporation. Microsoft, MS, Windows, and MS-DOS are registered trademarks of Microsoft Corporation. IBM is a trademark of International Business Machines Corporation. 77-0100-001 12 September 2000 iii Compliance Statements The GoBook (IX250) computer has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. The GoBook (IX250) computer complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area. The GoBook (IX250) computer may be connected to the telephone network using the RJ-11 jack provided. 77-0100-001 12 September 2000 GoBook™ User’s Manual iv If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please contact the equipment manufacturer for repair and/or warranty information. Do not attempt repairs of this equipment yourself without obtaining manufacturer authorized parts and documentation. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved. Compliance Statement for Canada NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own prot…

Text truncated - open the document above for the full version.

Celltech Research Inc. 1955 Moss Court, Kelowna, B.C. V1Y 9L3 Canada Tel. 250-860-3130 • Fax. 250-860-3110 • [email protected] www.globuswireless.com/celltech/celltech.htm October 24, 2000 Federal Communications Commission Equipment Approval Services 7435 Oakland Mills Road Columbia, MD 21046 SUBJECT: ITRONIX CORPORATION FCC ID: KBCIX250RIM902 Part 90 Certification Gentlemen: On behalf of Itronix Corporation we hereby submit an application for Part 90 Certification of the Itronix Rugged Laptop PC with RIM 902 Mobitex radio modem as follows: FCC ID: KBCIX250RIM902 Model(s): IX250 Equipment Class: Licensed Non-Broadcast Station Transmitter (TNB) Equipment Type: Rugged Laptop PC with Mobitex Radio Modem Tx Freq. Range: 896 - 901 MHz Rx Freq. Range: 935 - 941 MHz Max. RF Output Power: 1.76 Watts Emission Designator: 12K8F1D Attached is the Letter of Authorization, Confidentiality Request, measurement report data and test plots, SAR measurement report data & photographs, MPE measurement report data & photographs, FCC ID label and location, test setup photographs, internal and external photographs, block diagrams (confidential), schematic diagrams (confidential), operational description (confidential), parts list & tune-up procedure (confidential), and the user's manual with RF exposure warning statement. If you have any questions or comments concerning the above, please contact the undersigned. Sincerely, Shawn McMillen General Manager Celltech Research Inc. Testing & Engineering Lab cc: Itronix Corporation

RESEARCH IN MOTION Research In Motion Limited 295 Phillip Street Waterloo, Ontario Canada N2L 3W8 +1 519 888 7465, fax +1 519 888 6906 E-mail: [email protected] Our Ref: 01947-CERT-FCC-COVER-021_mod2October 26, 2000 Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21045 Reference :FCC ID : L6AR902M-2-O Subject :Letter requesting confidentiality of R902M-2-O radio modem device FCC Certification application. Pursuant to CFR 47 Chapter 1 Section 0.459, Research In Motion Limited (RIM) requests that the following identified detailed technical information regarding the R902M-2-O device be held confidential by the Federal Communication Commission (FCC) and as such be withheld from public inspection. RIM does not disclose proprietary confidential information about our products to any third parties and as such we request that the FCC does the same and forward the confidentiality acceptance letter to RIM. Our FCC submissions are considered proprietary confidential information. Pursuant to CFR 47 Chapter 1 Sections 0.457(d) and 0.457(d)(2)(i) the exhibits contain details of trade secrets and technical data that is customarily guarded from competitors and not released to the public by Research In Motion Limited. The specific parts of the Exhibits indicated in this letter are considered confidential by RIM and as such should be prevented from disclosure to public and competitors. RIM has taken necessary measures to have limited access to confidential documents only to RIM internal employees on a need-to-know basis, and have signed confidentiality agreements with employees. If the disclosure of such information is made public, it will cause serious competitive harm to RIM. Previously, none of the requested confidential Exhibits have been disclosed to third parties by RIM. The following Exhibits with specific sections described, submitted with the Form 731 Attachments should be held confidential: Exhibit Parts List/Tune Up InfoSection 010-9-1 and 010-9-2, CFR 47 Section 2.983(d)(9) - Description of operational, test, and device tune-up technical procedure-“DOC-01606-007”, and operators’ manual-“DOC- 01606-008” Section 010-10, CFR 47 Section 2.983(d)(10) - Description of frequency stabilizing circuitry Exhibit Parts List/Tune Up InfoSection 010-11-1, CFR 47 Section 2.983(d)(11) - Description of circuits for suppression of spurious radiation Section 010-11-2, CFR 47 Section 2.983(d)(11) - Description of circuits for modulation limiting Section 010-11-3, CFR 47 Section 2.983(d)(11) - Description of circuits for power limiting Exhibit Operational DescriptionSection 010-12 and 010-12-1, CFR 47 Section 2.983(d)(12) - Description of digital modulation format and necessary bandwidth Exhibit Parts List/Tune Up InfoSection 010-12-2 and 010-12-3, CFR 47 Section 2.983(d)(12) – Modulation generation methods and circuits. Detailed diagrams of modulation format and generation methods and circuits Exhibit Operational DescriptionSection 011-1 and 011-2, CFR 47 Sections 2.975(a)(3), 2.983(d)(6) and 2.1033(b)(4) - Detailed system and functional description Exhibit Parts List/Tune Up InfoSection 011-3, CFR 47 Sections 2.975(a)(3), 2.983(d)(6) and 2.1033(b)(4) - Detailed technical RF and electrical circuit description Exhibit Block Diagram01947-CERT-FCC-BLOCK-“R902M-2-O RADIO BLOCK”, CFR 47 Section 2.983(d)(6) – Detailed technical radio modem block diagram Exhibit Schematics“Tadpole OEM” SCH-01947-001, CFR 47 Section 2.983(d)(7) - Complete technical schematic circuit diagrams Yours truly, MasudS.Attayi,P.Eng. Senior Certification Engineer Research In Motion Limited ( 519 ) 888 – 7465 x 2442 [email protected] RESEARCH IN MOTION Research In Motion Limited 295 Phillip Street Waterloo, Ontario Canada N2L 3W8 +1 519 888 7465, fax +1 519 888 6906 E-mail: [email protected] Our Ref: 01947-CERT-FCC-Cover-022_mod2October 26, 2000 Federal Communications Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd. Columbia, Md. 21046 FCC ID:L6AR902M-2-O Subject:FCC Part 90 Certification Application for Research In Motion Limited, Model R902M-2-O This is to inform that Research In Motion is submitting the technical documentation of our radio modem Model R902M-2-O (existing FCC ID: L6AR902M-2-O ) in support of the application for Certification of our integrator, Itronix, IX250 PC with FCC ID KBCIX250RIM902. The Model R902M-2-O is a radio modem intended for integration into other equipment to allow wireless data communication. All required documents in compliance with Parts 2 and 90 of the FCC Rules have been provided in the attached Exhibits. Research In Motion would like to request confidentiality as indicated in the Form 731, Item 8 and as requested in the letter Ref: CERT-01677-021_mod2, under Exhibit “Covering Letters”. Please do hesitate to call at (519) 888-7465 x2442 or email at [email protected] should you require additional information or have any questions. Yours truly, MasudS.Attayi,P.Eng. Senior Certification Engineer Research In Motion Limited ( 519 ) 888 – 7465 x 2442 [email protected]

CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 © 2000 Celltech Research Inc. ITRONIX IX250 FCC ID: KBCIX250RIM902 Rugged Laptop PC with RIM 902 Mobitex Radio Modem EXTERNAL EUT PHOTOGRAPHS CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 © 2000 Celltech Research Inc. ITRONIX IX250 FCC ID: KBCIX250RIM902 Rugged Laptop PC with RIM 902 Mobitex Radio Modem EXTERNAL EUT PHOTOGRAPHS

CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 © 2000 Celltech Research Inc. ITRONIX FCC ID: KBCIX250RIM902 Rugged Laptop PC with Mobitex Radio Modem FCC ID LABEL & LOCATION LABELLING REQUIREMENTS PER §§ 2.925 The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase.

CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 © 2000 Celltech Research Inc. ITRONIX IX250 FCC ID: KBCIX250RIM902 Rugged Laptop PC with RIM 902 Mobitex Radio Modem INTERNAL EUT PHOTOGRAPHS CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 © 2000 Celltech Research Inc. ITRONIX IX250 FCC ID: KBCIX250RIM902 Rugged Laptop PC with RIM 902 Mobitex Radio Modem INTERNAL EUT PHOTOGRAPHS CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 © 2000 Celltech Research Inc. ITRONIX IX250 FCC ID: KBCIX250RIM902 Rugged Laptop PC with RIM 902 Mobitex Radio Modem INTERNAL EUT PHOTOGRAPHS

CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna, Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 _________________________________________________________________________________________________________ © 2000 Celltech Research Inc. CERTIFICATE OF COMPLIANCE SAR EVALUATION This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in ANSI/IEEE Std. C95.3-1999. (See test report). I attest to the accuracy of data. All measurements were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Celltech Research Inc. certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Shawn McMillen General Manager Celltech Research Inc. Test Lab: CELLTECH RESEARCH INC. Testing and Engineering Lab 1955 Moss Court Kelowna, B.C. Canada V1Y 9L3 Phone: 250 - 860-3130 Fax: 250 - 860-3110 Toll Free: 1-877-545-6287 e-mail: [email protected] web site: www.globuswireless.com Applicant Name: ITRONIX CORPORATION 801 South Stevens Street Spokane, WA 99204 Attn: Fred Phillips, Certification Engineer Phone: 509-742-1506 Fax: 509-626-4204 FCC ID: KBCIX250RIM902 Model(s): IX250 Equipment Type: Rugged Laptop PC with RIM 902 Mobitex Radio Modem Tx Frequency Range: 896 - 902 MHz Rx Frequency Range: 935 - 941 MHz Max. RF Output Power: 1.76 Watts FCC Rule Part(s): 2.1093; ET Docket 96.326 CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna, Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 _________________________________________________________________________________________________________ © 2000 Celltech Research Inc. TABLE OF CONTENTS 1.0 INTRODUCTION.................................................................. 1 2.0 DESCRIPTION OF EUT.......................................................... 1 3.0 SAR MEASUREMENT SYSTEM ............................................. 2 4.0 MEASUREMENT SUMMARY.................................................. 3 5.0 SAR LIMITS........................................................................ 3 6.0 DETAILS OF SAR EVALUATION........................................... 4 7.0 EVALUATION PROCEDURES................................................. 5 8.0 SYSTEM VALIDATION.......................................................... 5 9.0 SIMULATED EQUIVALENT TISSUES...................................... 6 10.0 TISSUE PARAMETERS......................................................... 6 11.0 SYSTEM SPECIFICATIONS.................................................... 7 12.0 TEST EQUIPMENT LIST........................................................ 8 13.0 MEASUREMENT UNCERTAINTIES........................................ 9 14.0 REFERENCES...................................................................... 10 APPENDIX A - SAR MEASUREMENT DATA........................................ 11 APPENDIX B - DIPOLE VALIDATION................................................ 12 APPENDIX C - PROBE CALIBRATION............................................... 13 APPENDIX D - TEST SETUP PHOTOGRAPHS..................................... 14 CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna, Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 _________________________________________________________________________________________________________ © 2000 Celltech Research Inc. ITRONIX IX250 FCC ID: KBCIX250RIM902 1 Rugged Laptop PC with RIM 902 Mobitex Radio Modem 1.0 INTRODUCTION This measurement report is designed to show compliance of the Itronix Model: IX250 Rugged Laptop PC with RIM 902M-2-0 Mobitex Radio Modem FCC ID: KBCIX250RIM902 with FCC Part 2.1093, ET Docket 96-326 Rules for mobile and portable devices. The test procedures, as described in American National Standards Institute C95.1 - 1992 (1), FCC OET Bulletin 65– 1997 were employed. A description of the product and operating configuration, detailed summary of the test results, methodology and procedures used in the evaluation, equipment used, and the various provisions of the rules are included within this test report. 2.0 DESCRIPTION of Equipment Under Test (EUT) Figure 1. Front of EUT Figure 2. Side of EUT Figure 3. Rear of EUT Figure 4. Radio Modem EUT Type Rugged Laptop PC with RIM 902 Mobitex Radio Modem Equipment Class Licensed Non-Broadcast Station Transmitter (TNB) Radio Type RIM 902M-2-O (Mobitex Network) Model No.(s) IX250 FCC ID KBCIX250RIM902 S/N No. Pre-production Tx Frequency Range (MHz) 896-902 Max. RF Output Power 1.76 Watts Rx Frequency Range (MHz) 935-941 Signal Modulation(s) GMSK Antenna Type Dipole Antenna Length 158 mm CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna, Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 _________________________________________________________________________________________________________ © 2000 Celltech Research Inc. ITRONIX IX250 FCC ID: KBCIX250RIM902 2 Rugged Laptop PC with RIM 902 Mobitex Radio Modem 3.0 SAR MEASUREMENT SYSTEM Celltech Research SAR measurement facility utilizes the Dosimetric Assessment System (DASY™) manufactured by Schmid & Partner Engineering AG (SPEAG™) of Zurich, Switzerland. The DASY system is comprised of the robot controller, computer, near-field probe, probe alignment sensor, and the generic twin phantom containing brain or muscle equivalent material (see Figure 6). The robot is a six-axis industrial robot performing precise movements to position the probe to the location (points) of maximum electromagnetic field (EMF). A cell c…

Text truncated - open the document above for the full version.

77-0100-001 12 September 2000 GoBook™ User’s Manual vi Warnings and Cautions WARNING It is important that only authorized Itronix personnel attempt repairs on Itronix equipment as this might void any maintenance contract with your company. Unauthorized service personnel might be subject to shock hazard on some Itronix equipment if removal of protective covers is attempted. The product you have purchased is powered by a rechargeable battery. The battery is recyclable and, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Do not crush the battery or place it in a fire. Check with your local solid-waste officials for details on recycling options or proper disposal. CAUTION Internal components of the GoBook (IX250) computer will be damaged if exposed to contaminants. When dust covers, the PC card door, or the battery door are open on the computer, shield the unit from all contaminants such as liquids, rain, snow, and dust. WARNING “In order to comply with the FCC RF exposure requirements this device must be operated with a minimum seperation distance of 4 cm between the user/nearby persons and the antenna in its intended vertical operating position.” “The antenna location is fixed in the upper right edge of the display screen and is not to be relocated” “The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connec- tion to the Public Switched Telephone Network (PSTN). However, due to differences between individual PSTNs provided in different countries the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.

CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna, Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 _________________________________________________________________________________________________________ © 2000 Celltech Research Inc. CERTIFICATE OF COMPLIANCE MPE EVALUATION This wireless device has been shown to be compliant for localized maximum permissible exposure (MPE) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in ANSI/IEEE Std. C95.3-1999. I attest to the accuracy of data. All measurements were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Celltech Research Inc. certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Shawn McMillen General Manager Celltech Research Inc. Test Lab: CELLTECH RESEARCH INC. Testing and Engineering Lab 1955 Moss Court Kelowna, B.C. Canada V1Y 9L3 Phone: 250 - 860-3130 Fax: 250 - 860-3110 Toll Free: 1-877-545-6287 e-mail: [email protected] web site: www.globuswireless.com Applicant Name: ITRONIX CORPORATION 801 South Stevens Street Spokane, WA 99204 Attn: Fred Phillips, Certification Engineer Phone: 509-742-1506 Fax: 509-626-4204 FCC ID: KBCIX250RIM902 Model(s): IX250 Equipment Type: Rugged Laptop PC with RIM 902 Mobitex Radio Modem, Vehicle Cradle, & (3) Vehicle Magnetic Mount Antennas Tx Frequency Range: 896 - 902 MHz Rx Frequency Range: 935 - 941 MHz Max. RF Output Power: 1.76 Watts FCC Rule Part(s): 2.1091; 1.1310; ET Docket 93-62 CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna, Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 _________________________________________________________________________________________________________ © 2000 Celltech Research Inc. TABLE OF CONTENTS 1.0 INTRODUCTION.................................................................. 1 2.0 DESCRIPTION OF EUT.......................................................... 1 3.0 MPE MEASUREMENT GUIDELINES........................................ 2 4.0 DEFINITION......................................................................... 2 5.0 MPE LIMITS........................................................................ 3-4 6.0 DETAILS OF MPE EVALUATION........................................... 5 7.0 MPE EVALUATION SUMMARY.............................................. 6-11 8.0 SYSTEM CALIBATION.......................................................... 12 9.0 SYSTEM SPECIFICATIONS.................................................... 12 10.0 REFERENCES...................................................................... 12 APPENDIX A - MPE TEST SETUP PHOTOGRAPHS.............................. 13 APPENDIX B - VEHICLE ANTENNA SPECIFICATIONS........................ 14 CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna, Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 _________________________________________________________________________________________________________ © 2000 Celltech Research Inc. ITRONIX IX250 FCC ID: KBCIX250RIM902 1 Rugged Laptop PC with RIM 902 Mobitex Radio Modem SCOPE Environmental evaluation measurements of Maximum Permissible Exposure (MPE) to radio frequency (RF) radiation from transmitting devices for compliance with the technical rules and regulations of the U.S. Federal Communications Commission (1). 1.0 INTRODUCTION This measurement report describes the Maximum Permissible Exposure (MPE) tests of Itronix Model: IX250 Rugged Laptop PC with RIM 902M-2-0 Mobitex Radio Modem (FCC ID: KBCIX250RIM902), vehicle cradle, and loaded with three (3) vehicle rooftop magnetic mount antennas. The test procedures described in FCC CFR47 2.1091, 1.1310, American National Standards Institute C95.1-1992 (2), C95.3-1992 (3), and OET Bulletin 65 (Edition 97-01)(4) were employed. A description of the product and operating configuration, detailed summary of the test results, methodology and procedures used in the evaluation, equipment used, and the various provisions of the rules are included within this test report. 2.0 DESCRIPTION of Equipment Under Test (EUT) EUT Type Rugged Laptop PC with RIM 902 Mobitex Radio Modem, Vehicle Cradle, & (3) Magnetic Mount Antennas Equipment Class Licensed Non-Broadcast Station Transmitter (TNB) Radio Type RIM 902M-2-O (Mobitex Network) FCC ID KBCIX250RIM902 Max. RF Output Power 1.76 Watts Model No.(s) IX250 Tx Frequency Range (MHz) 896-902 Signal Modulation(s) GMSK Rx Frequency Range (MHz) 935-941 Antenna Type(s) #1. Unity Gain #2. 5dB Gain #3. 5dB Gain Elevated CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna, Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 _________________________________________________________________________________________________________ © 2000 Celltech Research Inc. ITRONIX IX250 FCC ID: KBCIX250RIM902 2 Rugged Laptop PC with RIM 902 Mobitex Radio Modem 3.0 MPE MEASUREMENT GUIDELINES The Federal Communications Commission (FCC) has adopted the guidelines for evaluating the environmental effects of radio frequency radiation in ET Docket 93-62 on August 6, 1996 to protect the public from the potential hazards of RF emissions (1). The safety limits used for the environmental evaluation measurements are based on the criteria published by the American National Standards Institute (ANSI) for localized MPE in IEEE/ANSI C95.1-1992 Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz – 300 GHz (2). The measurement procedure described in IEEE/ANSI C95.3-1992 Recommended Practice for the Measurement of Potenti…

Text truncated - open the document above for the full version.

48 GoBook™ User’s Manual 77-0100-001 12 September 2000 Cisco Wireless LAN •Go to your preferred LAN applications and run normally. CAUTION This device has been tested and found to be compliant with FCC MPE (Maximum Permissible Exposure) requirements. In order to comply with FCC MPE requirements the user and all nearby persons must maintain a 20cm separation distance from the antenna when using this device with vehicle cradle. See Section 7 for important information about vehicle-mounted antennas.

CELLTECH RESEARCH INC. Test Report S/N: 100200-23KBC 1955 Moss Court, Kelowna Dates of Tests: October 02-04, 2000 B.C. CANADA V1Y 9L3 ____________________________________________________________________________________________________________________ © 2000 Celltech Research Inc. CERTIFICATE OF COMPLIANCE FCC PART 90 CERTIFICATION This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Celltech Research Inc. certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Shawn McMillen General Manager Celltech Research Inc. Test Lab: CELLTECH RESEARCH INC. Testing and Engineering Services 1955 Moss Court Kelowna, B.C. V1Y …

Text truncated - open the document above for the full version.