KXU-PDFSZ24Help Alert Pendant

Series 5.0 Software User Guide PN 0510-1059-A_DRAFT Series 5.0 Software User Guide Supports the 9450, 9600 Quick Response and Fall Management Systems PN: 0510-1059-A_DRAFT Release Date: 01/10/07 Users must read this guide before using the Product. Copyright 2007 by RF Technologies, Inc. All Rights Reserved. No Part of this work may be reproduced or copied in any form or by any means without written permission from RF Technologies, Inc. Important Warnings It is important for your facility to implement and enforce the following WARNINGS in order to keep all equipment functioning properly. WARNING INSTALLATION AND CONFIGURATION—It is the responsibility of the facility to follow the installation instructions carefully, as outlined in the Series 5.0 Software Administrator Guide, and to use the components and supplies specified by RF Technologies, Inc. for all installations. Failure to use the components and supplies specified by RF Technologies, Inc. may result in equipment and/or system failure. WARNING SYSTEM MAINTENANCE AND TESTING—It is the responsibility of the facility to establish and facilitate a regular maintenance schedule for your system, as outlined in the Series 5.0 Software Administrator Guide. This includes regular inspection, testing, and cleaning. RF Technologies, Inc. recommend monthly maintenance and testing of your system. It is also recommended that your facility keep records of maintenance and test completions. Failure to provide regular maintenance and testing of these products may result in equipment and/or system failure. WARNING SYSTEM INSPECTION—It is the responsibility of the facility to establish and facilitate a regular inspection schedule for your system. RF Technologies, Inc. recommend quarterly inspections of your system for safety and performance by a qualified RF Technologies, Inc. representative. To arrange for a quarterly inspection by RF Technologies, Inc., call our Technical Support Department at (800)-669-9946 or (262) 790-1771. Failure to provide regular inspection of these products may result in equipment and/or system failure. WARNING USER TRAINING—It is the responsibility of the facility to implement structured training procedures for all employees using the system. Only users who have received adequate training on the use of the system, as outlined in this manual, should use the system. Failure to adequately train employees may cause system failure due to user error. In addition, incorrect use of the equipment may also result in system failure. WARNING DISPOSAL—At the end of their service life the products described in this manual, as well as accessories (i.e. lithium batteries, banding material, disposable pads, etc.), must be disposed of in compliance with all applicable federal, state and local guidelines regulating the disposal of products containing potential environmental contaminants. Dispose of the packaging material by observing the applicable waste control regulations. WARNING PRODUCT WARRANTIES—Failure to follow the Warnings and Cautions in this guide voids any and all Product Warranties. Compliance Federal Communication Commission (FCC) Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance voids the user’s authority to operate the equipment. FCC and IC Radiation Exposure Statement for Mobile Devices (For the Pull Cord model 0800-0285 and 0800-0317; Universal Transceiver model 0800-0301, which covers part numbers 0800-0303, and 0800-0304; Router model 0800-0287; Asset Transceivers model 0800-0286 and model 0800-0302) This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC and IC Radiation Exposure Statement for Portable Devices (For the Pendant Transceivers model 0800-0288 and model 0800-0296) This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment is in direct contact with the body of the user under normal operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Compliance Changes or modifications not expressly approved by RF Technologies could void the user’s authority to operate the equipment. The Term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. This device has been designed to operate with the antennas listed below, and having a maximum gain of 3dBi. Antennas not included in this list or having a gain greater than 3dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Acceptable antennas are PCB antennas in all cases of the Router which uses a 2.4 GHz 1/2 wave RP-SMA. To reduce potential radio interference to other users, the antenna type and its gain should be so ch…

Text truncated - open the document above for the full version.

LETTER OF AUTHORIZATION FCC Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21045-0429 Ladies and or Gentlemen: I appoint Brian J. Mattson or Amom C. Rowe to act as agent in the preparation of applications under Part 15 of the Rules and Regulations of the Federal Communications Commission. I certify that the exhibits properly describe the device being submitted under this application and will implement any changes described in the test report. The following statement is required by the Federal Communications Commission: By checking yes, the applicant certifies that, in the case of an individual applicant, he or she is not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a), or, in the case of an non-individual applicant (e.g. corporation, partnership or other unincorporated association), no party to the application is subject to a denial of federal benefits, that includes FCC benefits, pursuant to that section. X YES NO Dated this 29th day of January 2007 Agency agreement expiration date: None John LaBorde Printed Title Manufacturing Engineer . Telephone 262-790-1771 Applicant RF Technologies, Inc.

Request for Confidentiality Date: January 30, 2007 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: KXU-PDFSZ24 Pursuant to 47 CFR Section 0.459 RF Technologies, Inc. understands that requests for non disclosure and confidential treatment is being made for the following information as stated under the Code of Federal Regulations Chapter 47, Part 0.459 and behalf of APPLICANT NAME: • Block Diagram • Schematics • Technical Product Description The above materials contain trade secrets, proprietary and technical information that would customarily be guarded from competitors under 47 CFR section 0.457(d)(2). Disclosure or publication of any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. RF Technologies, Inc. understands that pursuant to 47 CFR section 0.457(d)(1)(ii) disclosure of the applicant and all accompanying documentation will not be made before the date of the grant. Thank you for your attention to this matter. Signatory Arnom C. Rowe EMC ENGINEER EMC-001375-NE D.L.S. Electronic Systems, Inc.

Letter of Agency Date: January 30, 2007 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: Please be advised that RF Technologies, Inc. authorizes D.L.S. Electronic Systems, Inc. to act on our behalf, until otherwise notified, for applications submitted to American Telecommunications Certification Body, Inc. (ATCB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you for your attention to this matter. Signatory, Arnom C. Rowe EMC ENGINEER EMC-001375-NE D.L.S. Electronic Systems, Inc. FCC Labeling Requirements and Information Date: January 30, 2007 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: FCC Labeling Requirements FCC ID: KXU-PDFSZ24 The following label information is required by the FCC Rules and Regulations for certified devices. Also attached, please find marketing information required by the FCC Rules and Regulations. Thank you for your attention to these matters. Sincerely, Arnom C. Rowe EMC ENGINEER EMC-001375-NE D.L.S. Electronic Systems, Inc. Modification Letter Date: January 30, 2007 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: KXU-PDFSZ24 Please be advised that the following information is a list of modifications that will be included in the production process for the above-referenced equipment. Change 1: There were no modifications made during testing. Change 2: Change 3: Change 4: Change 5: Change 6: Change 7: Change 8: Change 9 Change 10: Thank you for your attention to this matter. Signatory Arnom C. Rowe EMC ENGINEER EMC-001375-NE D.L.S. Electronic Systems, Inc. Manufacturer’s Letter Date: January 30, 2007 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: KXU-PDFSZ24 To Whom It May Concern: Please be advised that the manufacturer will ensure that the above-referenced model will be manufactured in accordance with the FCC Rules and Regulations. Thank you for your attention to this matter. Signatory Arnom C. Rowe EMC ENGINEER EMC-001375-NE D.L.S. Electronic Systems, Inc.

FCC ID: KXU-PDFSZ24 D.L.S. ELECTRONIC SYSTEMS, INC. 1250 Peterson Drive Wheeling, Illinois 60090 FCC Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21045-0429 Gentlemen: We are submitting for RF Technologies, Inc., a Help Alert Pendant Transmitter, Model Number: 0800-0296, with a FCC ID: KXU-PDFSZ24 for Certification. This unit has been tested and complies to Part 15, Subpart C. If there are any questions in regards to this application, please call D.L.S. Electronic Systems, Inc. at (847) 537 6400. Enclosed you will find a copy of our test report with the information and results of tests that is required under Part 15, Section 15.247. Thank you for your assistance in this matter. Sincerely, Arnom C. Rowe EMC-001375-NE DLS/sr

Safety for What Matters Most Wandering Management Solutions u Wandering Management Solutions u 3125 N. 126th St. Brookfield, WI 53005 1-800-669-9946 n 262-790-1771 n Fax: 262-790-1784 www.rft.com n [email protected] Top Tag line on all cut sheets Tite in Arial Bold Blue logo Centered, indivual tag line RFT logo and address at bottom on all Cut sheets Center text in Arial 10 pt regulat Headings Arial Bold 14 pt Bulleted list with Round Bullets Pendant Transceiver 3125 N. 126th St. Brookfield, WI 53005 1-800-669-9946 n 262-790-1771 n Fax: 262-790-1784 www.rft.com n [email protected] Safety For What Matters Most Features - Completely wireless - Advanced 2.4 GHz Direct Sequence Spread Spectrum Technology - Fully supervised - Easy to use Resident Confidence The Pendant Transceiver can be used with all Quick Responseq Wireless Call Solutions. The transceiver is worn around the resident's neck or clipped to a belt. This wireless device allows residents to move about your facility with the confidence that if they are in need of assistance, they can easily summon help with the press of a button. Continuous Assurance of Proper Operation The Quick Response Wireless Call Solution fully supervises the transceiver and will alert staff if a problem develops or if the transceiver is outside the area of coverage. The transceiver is battery operated, and the battery can be replaced by the facility. When the battery is low, staff is continuously notified until the battery is changed. Advanced Direct Sequence Spread Spectrum Technology The transceiver operates in the 2.4 GHz frequency band using Advanced Direct Sequence Spread Spectrum Technology. This technology assures reliable signal reception over a large area. Specifications Power 3.0V Lithium battery Battery Life 1-2 years Frequency 2.4 GHz Direct Sequence Spread Spectrum Frequency Range 2.405 - 2.480 GHz Bandwidth 5 MHz Transmit Power 0 dBm Certification FCC, Part 15 Zigbee 802.15.4 compliant Size 2.13" H x 1.34" W x .60" D (5.41 cm x 3.40 cm x 12.7 cm) Weight 1.4 oz. (39.69g)

Company: RF Technologies Model: 0800-0296 (ZigBee Pendant with Freescale) FCC ID: KXU-PDFSZ24 IC: 2719A- PDFSZ24 Date: 01-10-2007 Photo Description: Outside covers Company: RF Technologies Model: 0800-0296 (ZigBee Pendant with Freescale) FCC ID: KXU-PDFSZ24 IC: 2719A- PDFSZ24 Date: 01-10-2007 Photo Description: Inside covers

3125 N. 126 th Street, Brookfield, Wisconsin 53005 Label Part Number: 0150-0582 Description: Pendant FCC Label Revision: A Mark as follows: RF Technologies, Inc. www.rft.com 1.800.669.9946 Model: 0800-0296 FCC ID: KXU-PDFSZ24 IC: 2719A-PDFSZ24 Font: Arial Size: 9 All lettering to be black Use 1” x 1.25” polyvinyl waterproof label stock with an aggressive adhesive. Note: The user will open the pendant to insert the battery before giving the pendant to a patient, thereby guaranteeing visibility of the label. Pa ge: 1 Location of Label on CompletedUnit Page: 2

Company: RF Technologies Model: 0800-0296 (ZigBee Pendant with Freescale) FCC ID: KXU-PDFSZ24 IC: 2719A- PDFSZ24 Date: 01-10-2007 Photo Description: Circuit board – component side Company: RF Technologies Model: 0800-0296 (ZigBee Pendant with Freescale) FCC ID: KXU-PDFSZ24 IC: 2719A- PDFSZ24 Date: 01-10-2007 Photo Description: Circuit board – solder side

RF Exposure Statement 1. Standard Applicable According to 1.1307 (b)(1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. This is a portable device. 2. Measurement Result: This is a portable device and the max peak output power is -0.21 dBm (.00095 W). Lower than the low threshold of 60/f GHz = (24.19 mW), d<2.5 cm general population category. Therefor SAR/MPE measurement is not necessary.

1250 Peterson Dr., Wheeling, IL 60090 Company: RF Technologies, Inc. Model Tested: 0800-0296 Report Number: 12883 FCC Rules and Regulations / Intentional Radiators Operational in the 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz, Bands Part 15, Subpart C, Section 15.247 THE FOLLOWING ''MEETS'' THE ABOVE TEST SPECIFICATION Formal Name: Help Alert Pendant Kind of Equipment: Wireless Nurse Call Device Test Configuration: Wireless connection (Tested at 3 vdc) Model Number(s): 0800-0296 Model(s) Tested: 0800-0296 Serial Number(s): NA Date of Tests: January 8 & 10, 2007 Test Conducted For: RF Technologies, Inc. 3125 North 126th Street Brookfield State, Wisconsin 53066 NOTICE: “This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government”. Please see the "Additional Description of Equipment Under Test" page listed inside of this report. © Copyright 1983- 2006 D.L.S. Electronic Systems, Inc COPYRIGHT NOTICE This report or any portion their of, may not be reproduced or modified in any form without the expressed written consent of D.L.S. Electronic Systems, Inc. Page - 1 - 1250 Peterson Dr., Wheeling, IL 60090 Company: RF Technologies, Inc. Model Tested: 0800-0296 Report Number: 12883 SIGNATURE PAGE Report By: Arnom C. Rowe Test Engineer EMC-001375-NE Reviewed By: William Stumpf OATS Manager Approved By: Brian Mattson General Manager Company Official: RF Technologies, Inc. Page - 2 - 1250 Peterson Dr., Wheeling, IL 60090 Company: RF Technologies, Inc. Model Tested: 0800-0296 Report Number: 12883 TABLE OF CONTENTS i. Cover Page ...........................................................................................................................................1 ii. Signature Page .....................................................................................................................................2 iii. Table of Contents....................................................................................................................................3 iv. NVLAP Certificate of Accreditation ...............................................................................................5 1.0 Summary of Test Report ..................................................................................................................6 2.0 Introduction......................................................................................................................................6 3.0 Object ...............................................................................................................................................6 4.0 Test Set-Up ......................................................................................................................................7 5.0 Test Equipment ................................................................................................................................7 6.0 Ambient Measurements ...................................................................................................................8 7.0 Description of Test Sample..............................................................................................................9 8.0 Additional Description of Test Sample..........................................................................................10 9.0 Photo Information and Test Set-Up ...............................................................................................11 10.0 Radiated Photos Taken During Testing .........................................................................................12 11.0 Results of Tests ..............................................................................................................................14 12.0 Conclusion .....................................................................................................................................14 TABLE 1 – EQUIPMENT LIST ...............................................................................................................15 Page -3- 1250 Peterson Dr., Wheeling, IL 60090 Company: RF Technologies, Inc. Model Tested: 0800-0296 Report Number: 12883 TABLE OF CONTENTS Appendix A – Electric Field Radiated Emissions Test..............................................................................17 1.0 Conducted Emission Measurements ..............................................................................................18 2.0 Spurious Emissions at the Antenna Terminals ..............................................................................19 2.0 Conducted Emission Data and Charts made at the Antenna Terminals ........................................20 3.0 Conducted Emissions Photos Taken During Testing.....................................................................33 4.0 Restricted Bands ............................................................................................................................34 5.0 Band Edge and Restrict Band Compliance ....................................................................................34 5.0 Data and Graph(s) taken showing the Band Edge and Restrict Band Compliance .......................35 6.0 Field Strength of Spurious Emission Measurements .....................................................................38 6.0 Radiated Data and Graph(s) taken for Field Strength Spurious Emission Measurements ............40 7.0 6 dB Bandwidth Graphs taken during testing ................................................................................47 8.0 Peak Power Spectral Density Graph(s) taken during testing .........................................................51 9.0 Number of IEEE 802.15.4 Zigbee Frequencies taken during testing ............................................55 10.0 Time of Occupancy Graphs taken during testing ..........................................................................57 11.0 Conducted Peak Output Power Graphs Taken During t…

Text truncated - open the document above for the full version.