L9V-5374Multi DSL Wireless Router

CT-5374 Multi-DSL WLAN Router User Manual Version A2.1, April 30, 2010 261099-005 1 Preface This manual provides information related to the installation and operation of this device. The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts. If you find the product to be inoperable or malfunctioning, please contact technical support for immediate service by email at [email protected] For product update, new product release, manual revision, or software upgrades, please visit our website at http://www.comtrend.com Important Safety Instructions With reference to unpacking, installation, use, and maintenance of your electronic device, the following basic guidelines are recommended: • Do not use or install this product near water, to avoid fire or shock hazard. For example, near a bathtub, kitchen sink or laundry tub, or near a swimming pool. Also, do not expose the equipment to rain or damp areas (e.g. a wet basement). • Do not connect the power supply cord on elevated surfaces. Allow it to lie freely. There should be no obstructions in its path and no heavy items should be placed on the cord. In addition, do not walk on, step on, or mistreat the cord. • Use only the power cord and adapter that are shipped with this device. • To safeguard the equipment against overheating, make sure that all openings in the unit that offer exposure to air are not blocked. • Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightening. Also, do not use the telephone to report a gas leak in the vicinity of the leak. • Never install telephone wiring during stormy weather conditions. CAUTION:
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment. WARNING
Disconnect the power line from the device before servicing.
Power supply specifications are clearly stated in Appendix C - Specifications . Copyright Copyright©2010 Comtrend Corporation. All rights reserved. The information contained herein is proprietary to Comtrend Corporation. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of Comtrend Corporation. 2 NOTE: This document is subject to change without notice. Protect Our Environment This symbol indicates that when the equipment has reached the end of its useful life, it must be taken to a recycling centre and processed separate from domestic waste. The cardboard box, the plastic contained in the packaging, and the parts that make up this router can be recycled in accordance with regionally established regulations. Never dispose of this electronic equipment along with your household waste; you may be subject to penalties or sanctions under the law. Instead, please be responsible and ask for disposal instructions from your local government. FCC Compliance This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no grantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 3 Table of Contents CHAPTER 1 INTRODUCTION.......................................................................................................... 5 1.1 FEATURES....................................................................................................................................... 5 1.2 APPLICATION................................................................................................................................... 6 CHAPTER 2 INSTALLATION............................................................................................................ 7 2.1 HARDWARE SETUP.......................................................................................................................... 7 2.2 LED INDICATORS............................................................................................................................ 9 CHAPTER 3 WEB USER INTERFACE............................................................................................11 3.1 DEFAULT SETTINGS........................................................................................................................11 3.2 IP CONFIGURATION........................................................................................................................11 3.3 LOGIN PROCEDURE....................................................................................................................... 14 CHAPTER 4 D…

Text truncated - open the document above for the full version.

50 5.9.1 Default Gateway Select WAN Interfaces as default gateways and then click Save/Apply. NOTE: After enabling the Automatic Assigned Default Gateway, the device must be rebooted to activate the assigned default gateway. 5.9.2 Static Route This option allows for the configuration of static routes by destination IP. Click Add to create a static route or click Remove to delete a static route. 51 After clicking Add the following screen will display. Enter Destination Network Address, Subnet Mask, Gateway IP Address, and/or WAN Interface before clicking Apply/Save to add an entry to the routing table. 5.9.3 Policy Routing This option allows for the configuration of static routes by policy. Click Add to create a routing policy or Remove to delete one. 52 On the following screen, complete the form and click Save/Apply to create a policy. 5.9.4 RIP To activate RIP, configure the RIP version/operation mode and select the Enabled checkbox  for at least one WAN interface before clicking Save/Apply. 53 5.9.5 IPv6 Static Route This option allows for the configuration of static routes by destination IP. Click Add to create a static route or click Remove to delete a static route. After clicking Add the following screen will display. 54 Enter Destination IPv6 Address, Subnet Prefix Length, Gateway IPv6 Address, and/or Interface before clicking Save/Apply to add a routing entry. 5.10 DNS 5.10.1 DNS Server To obtain DNS information from a WAN interface, select the first radio button and then choose a WAN interface from the drop-down box. For Static DNS, select the second radio button and enter the IP Address of the primary (and secondary) DNS server(s). Click Apply/Save to save the new configuration. NOTE: You must reboot the router to make the new configuration effective. 5.10.2 Dynamic DNS The Dynamic DNS service allows you to map a dynamic IP address to a static 55 hostname in any of many domains, allowing the CT-5374 to be more easily accessed from various locations on the Internet. To add a dynamic DNS service, click Add. The following screen will display. Consult the table below for field descriptions. Field Description D-DNS provider Select a dynamic DNS provider from the list Hostname Enter the name of the dynamic DNS server Interface Select the interface from the list Username Enter the username of the dynamic DNS server Password Enter the password of the dynamic DNS server 56 5.11 DSL The DSL Settings screen allows for the selection of DSL modulation modes. For optimum performance, the modes selected should match those of your ISP. DSL Mode Data Transmission Rate - Mbps (Megabits per second) G.Dmt Downstream: 12 Mbps Upstream: 1.3 Mbps G.lite Downstream: 4 Mbps Upstream: 0.5 Mbps T1.413 Downstream: 8 Mbps Upstream: 1.0 Mbps ADSL2 Downstream: 12 Mbps Upstream: 1.0 Mbps AnnexL Supports longer loops but with reduced transmission rates ADSL2+ Downstream: 24 Mbps Upstream: 1.0 Mbps AnnexM Downstream: 24 Mbps Upstream: 3.5 Mbps VDSL2 Downstream: 100 Mbps Upstream: 60 Mbps Options Description Inner/Outer Pair Select the inner or outer pins of the twisted pair (RJ11 cable) Bitswap Enable Enables adaptive handshaking functionality SRA Enable Enables Seamless Rate Adaptation (SRA) Profile Selection 8a-d, 12a-b, 17a, 30a, US0 57 Advanced DSL Settings Click Advanced Settings to reveal additional options. On the following screen you can select a test mode or modify tones by clicking Tone Selection. Click Apply to implement these settings and return to the previous screen. On this screen you select the tones you want activated, then click Apply and Close. 58 5.12 UPnP Select the checkbox  provided and click Apply/Save to enable UPnP protocol. 59 5.13 Print Server The CT-5374can provide printer support through an optional USB2.0 host port. If your device has this port, refer to Appendix F - Printer Server for detailed setup instructions. 5.14 Interface Grouping Interface Grouping supports multiple ports to PVC and bridging groups. Each group performs as an independent network. To use this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button removes mapping groups, returning the ungrouped interfaces to the Default group. Only the default group has an IP interface. 60 To add an Interface Group, click the Add button. The following screen will appear. It lists the available and grouped interfaces. Follow the instructions shown onscreen. 61 Automatically Add Clients With Following DHCP Vendor IDs: Add support to automatically map LAN interfaces to PVC's using DHCP vendor ID (option 60). The local DHCP server will decline and send the requests to a remote DHCP server by mapping the appropriate LAN interface. This will be turned on when Interface Grouping is enabled. For example, imagine there are 4 PVCs (0/33, 0/36, 0/37, 0/38). VPI/VCI=0/33 is for PPPoE while the other PVCs are for IP set-top box (video). The LAN interfaces are ENET1, ENET2, ENET3, and ENET4. The Interface Grouping configuration will be: 1. Default: ENET1, ENET2, ENET3, and ENET4. 2. Video: nas_0_36, nas_0_37, and nas_0_38. The DHCP vendor ID is "Video". If the onboard DHCP server is running on "Default" and the remote DHCP server is running on PVC 0/36 (i.e. for set-top box use only). LAN side clients can get IP addresses from the CPE's DHCP server and access the Internet via PPPoE (0/33). If a set-top box is connected to ENET1 and sends a DHCP request with vendor ID "Video", the local DHCP server will forward this request to the remote DHCP server. The Interface Grouping configuration will automatically change to the following: 1. Default: ENET2, ENET3, and ENET4. 2. Video: nas_0_36, nas_0_37, nas_0_38, and ENET1. 5.15 Certificate A certificate is a public key, attached with its owner’s information (company name, server name, personal real name, contact e-mail, postal address, etc) and digital signatures. There will be one or more digital signatures attached to the certific…

Text truncated - open the document above for the full version.

100 Step 3: On the Wireless  Security screen, enable WSC by selecting Enabled from the drop down list box and set the WSC AP Mode to Unconfigured. 101 Step 4: Click the Save/Apply button at the bottom of the screen. The screen will go blank while the router applies the new Wireless settings. When the screen returns, press the Start AddER button, as shown above. Step 3 Step 4 102 Step 5: Now return to the Network folder and click the BroadcomAP icon. A dialog box will appear asking for the Device PIN number. Enter the Device PIN as shown on the Wireless  Security screen. Click Next. Step 6: Windows Vista will attempt to configure the wireless security settings. Step 7: If successful, the security settings will match those in Windows Vista. 103 Appendix F - Printer Server These steps explain the procedure for enabling the Printer Server. NOTE: This function only applies to models with an USB host port. STEP 1: Enable Print Server from Web User Interface. Select Enable on-board print server checkbox  and enter Printer name and Make and model NOTE: The Printer name can be any text string up to 40 characters. The Make and model can be any text string up to 128 characters. 104 STEP 2: Go to the Printers and Faxes application in the Control Panel and select the Add a printer function (as located on the side menu below). STEP 3: Click Next to continue when you see the dialog box below. 105 STEP 4: Select Network Printer and click Next. STEP 5: Select Connect to a printer on the Internet and enter your printer link. (e.g. http://192.168.1.1:631/printers/hp3845) and click Next. NOTE: The printer name must be the same name entered in the ADSL modem WEB UI “printer server setting” as in step 1. 106 STEP 6: Click Have Disk and insert the printer driver CD. STEP 7: Select driver file directory on CD-ROM and click OK. STEP 8: Once the printer name appears, click OK. 107 STEP 9: Choose Yes or No for default printer setting and click Next. STEP 10: Click Finish. 108 STEP 11: Check the status of printer from Windows Control Panel, printer window. Status should show as Ready. 109 Appendix G - Connection Setup Creating a WAN connection is a two-stage process. 1 - Setup a Layer 2 Interface (ATM, PTM or Ethernet). 2 - Add a WAN connection to the Layer 2 Interface. The following sections describe each stage in turn. G1 ~ Layer 2 Interfaces Every layer2 interface operates in one of three modes: Default, VLAN Mux or MSC. A short introduction to each of these three modes is included below for reference. It is important to understand the differences between these connection modes, as they determine the number and types of connections that may be configured. DEFAULT MODE In this mode there is a 1:1 relationship between interfaces and WAN connections, in that an interface in default mode supports just one connection. However, unlike the multiple connection modes described below, it supports all five connection types. The figure below shows the five connection types available in ATM default mode. VLAN MUX MODE This mode uses VLAN tags to allow for multiple connections over a single interface. PPPoE, IPoE, and Bridge are supported while PPPoA and IPoA connections are not. The figure below shows multiple connections over a single VLAN Mux interface. MSC MODE Multi-Service Connection (MSC) mode supports multiple connections over a single interface. As with VLAN Mux mode, PPPoA and IPoA connection types are not supported, while Bridging is unavailable for Ethernet WAN interfaces. After adding WAN connections to an interface, you must also create an Interface Group to connect LAN/WAN interfaces (see section G3 ~ More About MSC Mode). 110 G1.1 ATM Interfaces Follow these procedures to configure an ATM interface. NOTE: The CT-5374 supports up to 16 ATM interfaces. STEP 1: Go to Advanced Setup  Layer2 Interface  ATM Interface. This table is provided here for ease of reference. Heading Description Interface WAN interface name. VPI ATM VPI (0-255) VCI ATM VCI (32-65535) DSL Latency {Path0}  portID = 0 {Path1}  port ID = 1 {Path0&1}  port ID = 4 Category ATM service category Link Type Choose EoA (for PPPoE, IPoE, and Bridge), PPPoA, or IPoA. Connection Mode Default Mode – Single service over one connection Vlan Mux Mode – Multiple Vlan service over one connection MSC Mode – Multiple Service over one Connection QoS Quality of Service (QoS) status Remove Select items for removal STEP 2: Click Add to proceed to the next screen. NOTE: To add WAN connections to one interface type, you must delete existing connections from the other interface type using the remove button. 111 There are many settings here including: VPI/VCI, DSL Latency, DSL Link Type, Encapsulation Mode, Service Category, Connection Mode and Quality of Service. The table below shows xDSL Link Type availability with each Connection Mode. xDSL Link Type Connection Mode EoA* PPPoA IPoA Default Mode OK OK OK VLAN Mux Mode OK X X MSC Mode OK X X * EoA includes PPPoE, IPoE, and Bridge link types. Here are the available encapsulations for each xDSL Link Type:  EoA- LLC/SNAP-BRIDGING, VC/MUX  PPPoA- VC/MUX, LLC/ENCAPSULATION  IPoA- LLC/SNAP-ROUTING, VC MUX STEP 3: Click Apply/Save to confirm your choices. 112 On the next screen, check that the ATM interface is added to the list. For example, an ATM interface on PVC 0/35 in Default Mode with an EoA Link type is shown below. To add a WAN connection, go to section G2 ~ WAN Connections. G1.2 PTM Interfaces Follow these procedures to configure a PTM interface. NOTE: The CT-5374 supports up to four PTM interfaces. STEP 4: Go to Advanced Setup  Layer2 Interface  PTM Interface. This table is provided here for ease of reference. Heading Description Interface WAN interface name. DSL Latency {Path0}  portID = 0 {Path1}  port ID = 1 {Path0&1}  port ID = 4 PTM Priority Normal or High Priority (Preemption). Connection Mode Default Mode – Single service over one interface. Vlan Mux Mode – Multiple Vlan services over one int…

Text truncated - open the document above for the full version.

Comtrend Corporation 3F-1, 10 Lane 609, Chung Hsin Road, Section 5 San Chung City, Taipei Hsien, Taiwan 241 FCC ID: L9V-5374 Device Name: Multi DSL Wireless Router Model No.: CT-5374 Date: 5/7/2010 Federal Communications Commission To whom it may concern: We declare that the device “Multi DSL Wireless Router”, model number: CT-5374, FCC ID: L9V-5374, only 1-11 channels are available in USA, other channels will be disabled by software. Sincerely Yours, By: By: Bill.Wang (Signature) (Printed) Title : Applicant : Comtrend Corporation Address : 3F-1, 10 Lane 609, Chung Hsin Road, Section 5 San Chung City, Taipei Hsien, Taiwan 241 Tel : (886) 2 29998261 # 573 Fax: (886) 2 29954177

Comtrend Corporation 3F-1, 10 Lane 609, Chung Hsin Road, Section 5 San Chung City, Taipei Hsien, Taiwan 241 FCC ID: L9V-5374 Device Name: Multi DSL Wireless Router Model No.: CT-5374 Date: 2010/03/29 Federal Communications Commission Dear Sir: Pursuant to Section 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Descriptions The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. By: By: Bill.Wang (Signature) (Printed) Title : Applicant : Comtrend Corporation Address : 3F-1, 10 Lane 609, Chung Hsin Road, Section 5 San Chung City, Taipei Hsien, Taiwan 241 Tel : (886) 2 29998261 # 573 Fax: (886) 2 29954177

Comtrend Corporation 3F-1, 10 Lane 609, Chung Hsin Road, Section 5 San Chung City, Taipei Hsien, Taiwan 241 FCC ID: L9V-5374 Device Name: Multi DSL Wireless Router Model No.: CT-5374 Date: 2010/03/29 Federal Communications Commission To whom it may concern: I, the undersigned, hereby authorize Mr . Joe Hsieh / Application Examiner of ELECTRONICS TESTING CENTER, TAIWAN and hereafter referred to as ETC, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Mr . Joe Hsieh of ETC on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ELECTRONICS TESTING CENTER, TAIWAN as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product  compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, By: By: Bill.Wang (Signature) (Printed) Title : Applicant : Comtrend Corporation Address : 3F-1, 10 Lane 609, Chung Hsin Road, Section 5 San Chung City, Taipei Hsien, Taiwan 241 Tel : (886) 2 29998261 # 573 Fax: (886) 2 29954177

ETC Report No.: 10-03-MAS-006-01 Page A1 of A3 FCC ID. :L9V-5374 ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Outside view 1 of EUT 2. Outside view 2 of EUT ETC Report No.: 10-03-MAS-006-01 Page A2 of A3 FCC ID. :L9V-5374 3. Outside view 3 of EUT 4. Outside view 4 of EUT ETC Report No.: 10-03-MAS-006-01 Page A3 of A3 FCC ID. :L9V-5374 5. Adapter 6. Antenna connect

ID Label_Location FCC ID : L9V-5374 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID : L9V-5374 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ETC Report No.: 10-03-MAS-006-01 Page B1 of B4 FCC ID. :L9V-5374 ANNEX B: INTERNAL CONSTRUCTION PHOTOS OF EUT 1. Inside View 1 of EUT 2. Inside View 2 of EUT ETC Report No.: 10-03-MAS-006-01 Page B2 of B4 FCC ID. :L9V-5374 3. Inside View 3 of EUT 4. Module ETC Report No.: 10-03-MAS-006-01 Page B3 of B4 FCC ID. :L9V-5374 5. Module 6. Front view of PCB ETC Report No.: 10-03-MAS-006-01 Page B4 of B4 FCC ID. :L9V-5374 7. Rear view of PCB

Specification 1.Electical Properties RF Cable Assembly 1.1 Frequency Range ............................... 2.4~2.5GHz 1.2 Impedance .......................................... 50 Ω 1.3 VSWR ................................................ 2.0 Max 1.4 ANTENNA GAIN2 dBi 2.4 COLORBlack 2.Physical Properties 2.1 Cable Type ......................................... RG-178 Cable 2.2 Cable Connector1 ............................... SMA-Plug-Reverse 2.6 Storage Temperature ........................... -30°C ～ +75°C 2.5 Operating Temperature ....................... -20°C ～ +65°C 1.5 RADIATION PEATERN OMNI 2.3 ANTENNA COVERTPE Return Loss V. S . W. R Far-field amplitude, Eprincipal: Linear, Tau = 0.000 deg Gain = 1.90911 dBi Max far-field (global) = -44.91797 dB, Max far-field (plot) = -44.91798 dB Normalization: Reference, Network offset = 0.000 dB Hpeak at: -96.000 deg, Vpeak at: 0.000 deg Plot centering: On Antenna 802.11B 2dBi_H NSI2000 V4.0.174, Filename:C:\kao\20060606Antenna-2.4GHz\H.nsi Measurement date/time: 2/8/2007 17:08:54 PM, Filetype: NSI-97 Far-field Cut Analysis: Avg value: 1.529 dB -3. dB beam width: Not Found -6. dB beam width: Not Found -10. dB beam width: Not Found Left Sidelobe: Not Found Right Sidelobe: Not Found Far-field display setup Azimuth (deg) Span = 360.00001 deg, Center = 0.000 deg, #pts = 361 Start= -180.00001 deg, Stop = 180.00001 deg, Delta = 1.000 deg Elevation (deg) Center = 0.000 deg, #pts = 1 Selected beam(s) 1 of 3 Beam Frequency Azimuth Elevation Pol ---- --------- ------- --------- --- 1 2.400 GHz Azimuth Elevation Single-pol ======================================================================== Far-field amplitude, Eprincipal: Linear, Tau = 0.000 deg Gain = 2.05904 dBi Max far-field (global) = -45.56202 dB, Max far-field (plot) = -45.56203 dB Normalization: Reference, Network offset = 0.000 dB Hpeak at: -103.000 deg, Vpeak at: 0.000 deg Plot centering: On Antenna 802.11B 2dBi_H NSI2000 V4.0.174, Filename:C:\kao\20060606Antenna-2.4GHz\H.nsi Measurement date/time: 2/8/2007 17:08:54 PM, Filetype: NSI-97 Far-field Cut Analysis: Avg value: 1.761 dB -3. dB beam width: Not Found -6. dB beam width: Not Found -10. dB beam width: Not Found Left Sidelobe: Not Found Right Sidelobe: Not Found Far-field display setup Azimuth (deg) Span = 360.00001 deg, Center = 0.000 deg, #pts = 361 Start= -180.00001 deg, Stop = 180.00001 deg, Delta = 1.000 deg Elevation (deg) Center = 0.000 deg, #pts = 1 Selected beam(s) 1 of 3 Beam Frequency Azimuth Elevation Pol ---- --------- ------- --------- --- 2 2.450 GHz Azimuth Elevation Single-pol ======================================================================== Far-field amplitude, Eprincipal: Linear, Tau = 0.000 deg Gain = 2.06895 dBi Max far-field (global) = -45.79614 dB, Max far-field (plot) = -45.79616 dB Normalization: Reference, Network offset = 0.000 dB Hpeak at: -106.00001 deg, Vpeak at: 0.000 deg Plot centering: On Antenna 802.11B 2dBi_H NSI2000 V4.0.174, Filename:C:\kao\20060606Antenna-2.4GHz\H.nsi Measurement date/time: 2/8/2007 17:08:54 PM, Filetype: NSI-97 Far-field Cut Analysis: Avg value: 1.726 dB -3. dB beam width: Not Found -6. dB beam width: Not Found -10. dB beam width: Not Found Left Sidelobe: Not Found Right Sidelobe: Not Found Far-field display setup Azimuth (deg) Span = 360.00001 deg, Center = 0.000 deg, #pts = 361 Start= -180.00001 deg, Stop = 180.00001 deg, Delta = 1.000 deg Elevation (deg) Center = 0.000 deg, #pts = 1 Selected beam(s) 1 of 3 Beam Frequency Azimuth Elevation Pol ---- --------- ------- --------- --- 3 2.500 GHz Azimuth Elevation Single-pol ======================================================================== Far-field amplitude, Eprincipal: Linear, Tau = 0.000 deg Gain = 2.13338 dBi Max far-field (global) = -44.20898 dB, Max far-field (plot) = -44.20898 dB Normalization: Reference, Network offset = 0.000 dB Hpeak at: -90.000 deg, Vpeak at: 0.000 deg Plot centering: On Antenna 802.11B 2dBi_E NSI2000 V4.0.174, Filename:C:\kao\20060606Antenna-2.4GHz\E.nsi Measurement date/time: 2/8/2007 17:24:37 PM, Filetype: NSI-97 Far-field Cut Analysis: Avg value: -2.278 dB -3. dB beam width: 81.55 deg -6. dB beam width: 112.87 deg -10. dB beam width: 138.75 deg Left Sidelobe: Not Found Right Sidelobe: -0.12 dB at 91.755 deg Far-field display setup Azimuth (deg) Span = 360.00001 deg, Center = 0.000 deg, #pts = 361 Start= -180.00001 deg, Stop = 180.00001 deg, Delta = 1.000 deg Elevation (deg) Center = 0.000 deg, #pts = 1 Selected beam(s) 1 of 3 Beam Frequency Azimuth Elevation Pol ---- --------- ------- --------- --- 1 2.400 GHz Azimuth Elevation Single-pol ======================================================================== Far-field amplitude, Eprincipal: Linear, Tau = 0.000 deg Gain = 2.26517 dBi Max far-field (global) = -44.84233 dB, Max far-field (plot) = -44.84234 dB Normalization: Reference, Network offset = 0.000 dB Hpeak at: -89.00001 deg, Vpeak at: 0.000 deg Plot centering: On Antenna 802.11B 2dBi_E NSI2000 V4.0.174, Filename:C:\kao\20060606Antenna-2.4GHz\E.nsi Measurement date/time: 2/8/2007 17:24:37 PM, Filetype: NSI-97 Far-field Cut Analysis: Avg value: -2.288 dB -3. dB beam width: 78.91 deg -6. dB beam width: 110.15 deg -10. dB beam width: 136.40 deg Left Sidelobe: Not Found Right Sidelobe: -0.26 dB at 91.755 deg Far-field display setup Azimuth (deg) Span = 360.00001 deg, Center = 0.000 deg, #pts = 361 Start= -180.00001 deg, Stop = 180.00001 deg, Delta = 1.000 deg Elevation (deg) Center = 0.000 deg, #pts = 1 Selected beam(s) 1 of 3 Beam Frequency Azimuth Elevation Pol ---- --------- ------- --------- --- 2 2.450 GHz Azimuth Elevation Single-pol =============================…

Text truncated - open the document above for the full version.