LD7TLSTRFID MODULE

The Installation of RRFCS 1. Installation of RRFCS into the copying machine 1.1.RRFCS-T RRFCS-T is the TAG and is installed on the CRU – a toner bottle . An introduction example is shown in the following. 1-1 RRFCS-C RRFCS-C is the Coupler and is mounted to the “LB” which is inside the machine Pictures are shown below. 1-2 A process to exchange -The power supply of the machine is turned off. -The outer cover is opened. -The toner bottle is removed -The RRFCS-C is removed. Toner bottles Copying machine Fig.A-1: Attached position of RRFCS -C to machine Fig.A-2: Attached position of RRFCS -T to toner bottle Front Cover LB RRFCS-T Toner Bottle 2. Recommended Actions (example) 2.1. At machine Power-ON (a single attempt is made to communicate with the RRFCS-T) -RF-ON time – after power on = 30 – 90 seconds -Initialization / Access time (RRFCS-T not in range) = .5 seconds -Initialization / Access time (RRFCS-T in range same bottle) = < 1 second -Initialization / Access time (RRFCS-T in range different bottle) = 2 to 3 seconds -RF-OFF time – After Initialization / Access time RF is turned off. 2.2. At the machine working Access interval = Dependent on print coverage area. Typical coverage is 6%. -Typical Access Interval = 125 seconds -RF-ON time = On as bottle is rotating typically 30 seconds - Typical Access time = < 1 second -RF-OFF time = When bottle is stopped or access time is complete. 1.3. At the machine waiting/standby Access interval = only when a bottle is installed. -Initialization / Access time = See times stated in section 2.1. -RF-ON time = RF is turned on when the outer door closes. It is on for up to 10 seconds (time-out) attempting to Initialize / Access if no bottle is installed. -RF-OFF time = Follows time-out or initialization / access time REGULATORY INFORMATION FCC PART 15 COMPLIANCE THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. MODIFICATIONS TO THE EQUIPMENT NOT EXPRESSLY APPROVED BY XEROX COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. ANY HOST DEVICE THAT CONTAINS THIS MODULE IS REQUIRED TO CLEARLY STATE THE FOLLOWING ON THE OUTSIDE OF THE HOST DEVICE: “CONTAINS FCC ID: LD7TLST”

Correspondence Summary Q & A November 17, 2005 SUBJECT: XEROX CORPORATION - FCC ID: JD7TLST 1. Question about additional justification needed for Modular approval - RF shield requirement of item 1 of DA001407. Answer: The module complies with the radiated emissions requirements for the applicable rule parts in its current state. Additional shielding to satisfy these requirements is not necessary. Furthermore, this particular module has a specific installation configuration. The module will be attached to the metal L-bracket as shown in the operational description. The purpose of the module will be to exchange information with the toner bottle inside a copier or printer. As a result the side of the module not facing the L- bracket will be facing the toner cartridge. The typical implementation of this module will be such that there no cables directly over or under the module that may be coupled to. Please reference the user manual to see the typical installation of the module. Additionally, the relatively low power intentionally radiated by the equipment should also help to reduce the probability of unintended coupling within host devices. TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 [email protected]

Siemic Laboratories Accessing Global Markets 2206 Ringwood Avenue, San Jose, CA 95131, USA, +1(408)526 1188, +1(408)526 1088, [email protected] Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA 26 October 2005 RE: Confidentiality Request Dear Reviewer: This letter is a request for confidentiality for specific exhibits in reference to The Watt Stopper, Inc. filing for the TLST under the FCC ID: LD7TLST. The following exhibits are requested to be held in confidentiality and withheld from public inspection pursuant to 47 CFR 0.457(d): Schematics Block Diagrams Operational Description Users Manual These exhibits contain details of the proprietary operation of the product. These details are not readily discernible from the hardware, constitute trade secrets, and are not generally accessible by the public. This module is not intended for OEM re-sale and the Users Manual is a document internal to Xerox only. We request that the above documents and this letter be withheld from public inspection. Please contact us if further justification for any of the above exhibits is necessary. Sincerely, Alvin Ilarina

TIMCO ENGINEERING, INC. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 Date: October 26, 2005 RE: FCC ID: LD7TLST Dear Reviewer: The following items are intended to show compliance with the requirements for a Part 15 modular transmitter approval for the 13.56 MHz transmitter under consideration in this filing. 1. The modular transmitter will be shielded inside the host units. Since this unit will be installed in Xerox printers control of this shielding will be maintained by the grant holder. Please reference the operational description to see the shielding plate the module will be attached to and the normal position inside the host during a typical installation. 2. The modular transmitter only has data inputs inductively coupled via the toner cartridge tag assembly. This will ensure that no conditions of excessive data rates or over-modulation can occur. 3. The modular transmitter receives its DC power from a regulated supply from within the host and has an on board regulator as well. 4. The transmitter has an integral antenna. 5. The transmitter was tested in a stand-alone configuration. 6. The transmitter is labeled with its own FCC ID. The users manual contains instructions for host unit exterior labeling to use: “Contains FCC ID:” 7. The transmitter complies with all operating requirements applicable to the transmitter. 8. The transmitter complies with applicable RF exposure requirements. If there are additional questions please contact SIEMIC Laboratories at 408-526-1188. Sincerely Gary E. Myers Xerox EMC manager

External Photos Top Bottom

ID Labeling/Location Information Label Location Label Sample Label Location FCC ID: LD7TLST IC #: 482B-TLST

Internal Photos Top Bottom

TEST REPORT FROM d For TLST RFID Module To 47 CFR 15.225(e) Test Report Serial No.: SL05062603-XRX-004B This report supersedes none Remarks: Equipment complied with the specification [X ] Equipment did not comply with the specification [ ] This Test Report is Issued Under the Authority of: .......................................................................................................... Tested by: Alvin Ilarina, Test Enginner .......................................................................................................... Reviewed by: Leslie Bai, Lab Manager Issue date: 31 October 2005 Equipment Details: Manufacturer: Xerox Corporation This test report may be reproduced in full only. Registration No. 783147 Registration No. 2195 Registration No. 4842 RTA No. D23/16V Lab Code: KR0032 Title: Xerox Corporation TLST RFID Module To: 47 CFR 15.225(e) Serial#SL05062603-XRX-004B Issue Date 31 October 2005 Page 2 of 18 www.siemic.com This page has been left blank intentionally. Title: Xerox Corporation TLST RFID Module To: 47 CFR 15.225(e) Serial#SL05062603-XRX-004B Issue Date 31 October 2005 Page 3 of 18 www.siemic.com CONTENTS EXECUTIVE SUMMARY..............................................................................................................................................5 1 TECHNICAL DETAILS..........................................................................................................................................6 2 TESTS REQUIRED..................................................................................................................................................7 3 MEASUREMENTS, EXAMINATIONS AND DERIVED RESULTS.................................................................8 4 TEST INSTRUMENTATION................................................................................................................................11 APPENDIX A: EUT TEST CONDITIONS.................................................................................................................12 APPENDIX B: EXTERNAL PHOTOS........................................................................................................................13 APPENDIX C: CIRCUIT/BLOCK DIAGRAMS.......................................................................................................14 APPENDIX D: INTERNAL PHOTOS.........................................................................................................................15 APPENDIX F: PRODUCT DESCRIPTION...............................................................................................................16 APPENDIX H: FCC LABEL LOCATION..................................................................................................................17 APPENDIX I: USER MANUAL...................................................................................................................................18 Title: Xerox Corporation TLST RFID Module To: 47 CFR 15.225(e) Serial#SL05062603-XRX-004B Issue Date 31 October 2005 Page 4 of 18 www.siemic.com This page has been left blank intentionally. Title: Xerox Corporation TLST RFID Module To: 47 CFR 15.225(e) Serial#SL05062603-XRX-004B Issue Date 31 October 2005 Page 5 of 18 www.siemic.com Executive Summary The purpose of this test programme was to demonstrate compliance of the Xerox Corporation, TLST RFID Module against the current 47 CFR 15.225(e). The TLST RFID Module demonstrated compliance with the 47 CFR 15.225(e). Xerox Corporation is the applicant and claimed manufacturer of this tested product. For the detailed description of this product, please refer to the TLST RFID Module User Manual. The test has demonstrated that this unit complies with stipulated standards. Title: Xerox Corporation TLST RFID Module To: 47 CFR 15.225(e) Serial#SL05062603-XRX-004B Issue Date 31 October 2005 Page 6 of 18 www.siemic.com 1 Technical Details Purpose Compliance testing of TLST RFID Module with 47 CFR 15.225(e) Applicant / Client Xerox Corporation 800 Salt Road Webster, NY 14580 Manufacturer Xerox Corporation Laboratory performing the tests SIEMIC Labs 2206 Ringwood Avenue San Jose, CA 95131 Test location(s) SIEMIC Labs 2206 Ringwood Avenue San Jose, CA 95131 Test report reference number SL05062603-XRX-004B Date EUT received 31 October 2005 Standard applied 47 CFR 15.225(e) Dates of test (from – to) 31 October 2005 to 31 October 2005 No of Units: 1 Equipment Category: DXX Trade/Product Name: TLST RFID Module Type/Model Name/No: TLST RFID Module Technical Variants: none FCC ID No. LD7TLST Title: Xerox Corporation TLST RFID Module To: 47 CFR 15.225(e) Serial#SL05062603-XRX-004B Issue Date 31 October 2005 Page 7 of 18 www.siemic.com 2 Tests Required The product was tested in accordance with the following specifications. The test results recorded in this Test Report are exclusively referred to the tested sample(s). Test Standard Description Pass / Fail 47 CFR Part 15.225 15.225(e) Frequency Stability: Temperature Variations Pass 15.225(e) Frequency Stability: Voltage Variations Pass Notes: Deviations to above standards are outlined in specific test sections if applicable. Cable loss and external attenuation are compensated for in the measurement system when applicable. Title: Xerox Corporation TLST RFID Module To: 47 CFR 15.225(e) Serial#SL05062603-XRX-004B Issue Date 31 October 2005 Page 8 of 18 www.siemic.com 3 Measurements, Examinations and Derived Results 3.1 General observations Equipment serial number(s) Module: Part number: Serial number: TLST RFID Module TLST RFID Module none Title: Xerox Corporation TLST RFID Module To: 47 CFR 15.225(e) Serial#SL05062603-XRX-004B Issue Date 31 October 2005 Page 9 of 18 www.siemic.com 3.2 Test Results 3.2.1 Frequency Stability: Temperature Variations Requirement(s): 47 CFR §15.225(e) Procedure: The frequency stability was measured at the antenna terminal using a spectrum analyzer. The measurements were made using the frequency co…

Text truncated - open the document above for the full version.

EMC Test Report Number EMC05006 EMC Test Group Report Form 5 Revision 5 Page 1 of 22 The Document Company Xerox EMC Test Group FCC Part 15, Subpart C and Industry Canada RSS-210 Compliance Report for Xerox Corporation Short Range Radio Frequency Identification (RFID) Device Model: TLST Judgement: The Device Under Test (DUT) met the requirements specified in FCC Part 15, Subpart C, Sections 15.207, 15.209 and 15.225, and Industry Canada RSS-GEN, Sections 6 and 7.2.2. The FCC and Industry Canada specified frequency stability tests were not performed as part of this assessment. Accreditation Certificate Number: 1248-01 Electrical (EMC) Testing This laboratory is accredited by the American Association for Laboratory Accreditation (A2LA) and the results shown in this test report have been determined in accordance with the laboratory’s terms of accreditation unless stated otherwise in the report. The client is hereby notified that products, materials or other items in this report are in no way approved or endorsed by A2LA unless A2LA explicitly permits such endorsement or approval. EMC Test Report Number EMC05006 EMC Test Group Report Form 5 Revision 5 Page 2 of 22 Type of Report: Electromagnetic Emissions Compliance Test Report Product: Xerox Corporation RFID Device, Model TLST Abstract: This report documents the testing completed on an RFID Model TLST as supplied by the client. The DUT was found to conform with the Federal Communications Commission, and Industry Canada regulatory limits for an intentional radiator and low power licence-exempt radiocommunication device, respectively. FCC is an acronym for “Federal Communications Commission. The FCC acronym is used throughout the document in lieu of the CFR 47 Part 15 Subpart C terminology. The IC acronym is used throughout the document in lieu of the Industry Canada RSS-GEN and RSS-210 terminology. Laboratory: Xerox Corporation Client: Heiko Rommelmann EMC Test Group Xerox Corporation 800 Salt Road Building 843 XSBG/SDU/PCDU Mail Stop 843-16S 800 Phillips Road Building 201 Webster, NY 14580 Mail Stop 201-03S (585) 422-4120 Webster, NY 14580 (585) 422-6449 (fax) (585) 422-0632 (585) 422-9311 (fax) Notice to Client: This report shall not be reproduced, except in full, without the written approval of the EMC Test Group. The client is hereby notified that the results of this report relate only to the item(s) tested. The client is responsible for ensuring that the appropriate information relating to the configuration of the product tested is documented and retained for future reference in accordance with CFR 47 Parts 2 & 15. The client is also responsible for ensuring the product is properly labeled and the customer documentation has the appropriate statements as noted in FCC Parts 2 and 15, and sections 5.10 and 5.11 of Industry Canada RSS-GEN and RSS-210. By signing below, the client certifies that the report distribution and product configuration documented in this test report is correct and that any modifications to the product noted in Section 2.6 shall be incorporated into all production units of the equipment for which this test report has been written. Client: Heiko Rommelmann Date: 11/15/05 Heiko Rommelmann, Product Manager Prepared By: David Spencer Date: 11/15/05 David Spencer, EMC Engineer DSSG / EH&S / EMC Test Group Approved By: Date: 11/15/05 Gary E. Myers, Manager DSSG / EH&S / EMC Group Distribution: Heiko Rommelmann 0201-03S David Spencer 843-16S Gary Myers 843-16S EMC Test Report Number EMC05006 EMC Test Group Report Form 5 Revision 5 Page 3 of 22 Table of Contents 1 GENERAL INFORMATION................................................................................................................4 1.1 Product Description......................................................................................................................................................................4 1.2 Related Reports / Approvals........................................................................................................................................................4 1.3 Tested System Details....................................................................................................................................................................5 1.3.1 Host Equipment.....................................................................................................................................................................5 1.4 Test Methodology / Reference Standards....................................................................................................................................5 1.5 Test Facility....................................................................................................................................................................................5 2 SYSTEM TEST CONFIGURATION...................................................................................................6 2.1 Justification....................................................................................................................................................................................6 2.2 Run Mode(s)..................................................................................................................................................................................6 2.3 Video Mode Justification..............................................................................................................................................................6 2.4 DUT Exercise Software.................................................................................................................................................................6 2.5 Special Accessories........................................................................................................................................................................6 2.6 Equipment Modifications............................…

Text truncated - open the document above for the full version.

Test Setup Photos Radiated Emissions Frequency Stability – Temperature Frequency Stability – Voltage Variations