LE2APPCAM25HDA720p WIFI Camera

IN THE BOX Camera (1)Antenna (1)Stand (1)AC Power Adapter (1) Quick Connect Guide (1) Ethernet to USB Cable (1) Screw Pack (1) SET UP CAMERA AND SMARTPHONE/TABLET This Quick Connect Guide only shows images for Android devices. Images for iOS devices are very similar. PREREQUISITES xYour router must support WEP/WPA/WPA2 security and it must be turned on. xYou must have an available WiFi-enabled mobile device (Android or iOS smartphone/tablet). xThe AppCam and your mobile device must connect to the same Wi-Fi router for setup. 1.Download the Uniden® AppCam™ app from the Apple iTunes store (iOS) or Google Play (Android) onto your device. 2.Connect the antenna to the camera. You can attach the camera stand to the camera as well but it is not necessary. Procedures for mounting the AppCam 25HD and attaching the camera are provided later in this Quick Connect Guide. 3.Connect the camera to power After about 45 seconds, the red LED is steady on and the green LED begins to flash (3-flash/pause pattern). A PPCAM25HDA QUICK START GUIDE Use this Quick Connect Guide to connect the camera on the network. If you want to set up more cameras later, refer to the online user manual for instructions. 2.Select your time zone. The most commonly used time zones are: ͳGMT-05:00 - Eastern Standard ͳGMT-06:00 - Central Standar ͳGMT-07:00 - Mountain Standard ͳGMT-08:00 - Pacific Standard ͳGMT-09:00 - Yukon Standard ͳGMT-10:00 - Alaska-Hawaii Standard 3.Set the Daylight Savings Time indicator. 4.Tap Back, and exit the Advanced Settings list. For complete operation instructions, refer to the online user manual at www.uniden.com TROUBLESHOOTING If ...TRY THIS ... My smartphone or wireless device cannot find the camera during setup. Make sure the camera’s green LED is blinking in a 3-flash/pause pattern. If it isn’t, reset the camera by pressing and holding the Reset button on the cord until the LEDs begin to flash. The app cannot find the camera -Make sure your network supports DHCP protocol. -Make sure that the DHCP option is turned on. -Make sure the camera and your mobile device connect to the same WiFi router. -Make sure the WiFi router is activated. -Make sure the camera is properly powered on. -Make sure the WiFi router has enabled SSID broadcasting. The camera does not find the router to connect to -Make sure you selected the correct router in the Manage WiFi Network box. -Make sure you entered the correct password for the router you selected in the Manage WiFi Network box. Issue 2, July 2014 CONNECT CAMERA AND MOBILE DEVICE 1.From your device’s Settings, go to WiFi. Select the AppCam 25HD to connect your device to it. The camera listing will be HD-XXXXXX where XXXXXX are the last 6 digits on the camera label. Enter the default password, 12345678. 2.When the device is connected to the camera, launch the app and tap the Add New System icon. 3.The System Information screen displays. Name the camera and tap Search.. 4.The Search in LAN results box displays. The camera’s DID should display. Tap the DID number. 5.The System Information screen displays again. This time, enter the security code (123456); tap Save. Tap YES, then NO at the next prompts. 6.The Globe screen displays. Tap the Globe to access the AppCam 25HD video. CONNECT CAMERA TO WIFI ROUTER 1.Tap the Back icon, the System icon, and then the System Settings icon. The System Information screen displays 2.Tap Advanced. Enter the Admin password (123456). 3.Scroll to WiFi on the Advanced Settings list. Tap Manage WiFi Network. Select your router from the drop-down list and enter your router’s password. Tap Connect. Your camera will reboot and reconnect to the router. Wait until the camera’s LEDs return to the steady on state to continue. 4.The Camera screen indicates that it is disconnected. Tap the System icon and then the Refresh icon. The camera refreshes and reconnects to the router you chose. The LEDs should be both on steady and app displays a photo of the video image. PLACING THE APPCAM 25HD Mount the AppCam 25HD Base 1.Hold the base of the camera stand where you want to mount it and mark the location of the screw holes. 2.Use the included screws and anchors to attach the base to the wall or ceiling. You can also screw the base into a flat surface such as a tabletop if needed. 3.Before attaching the camera, tug gently on the stand to make sure it is securely in place. Attach the Camera - AppCam 25HD 1.For each AppCam 25HD, attach the camera bracket to the mounting screw. You can attach the stand to the top or the bottom of the AppCam 25HD as needed. Tighten it a few turns, then turn the AppCam 25HD to face the direction you want. 2.Tighten the camera brace up against the AppCam 25HD to secure it into place. 3.Unlock the mounting post by turning the wingnut to the left a few turns. 4.Set the mounting post to the correct angle, then tighten the wingnut until the post is locked into place. 5.After the AppCam 25HD is installed, reconnect power. SET TIME ZONE/DAYLIGHT SAVINGS TIME It is important to set the correct time zone and daylight savings time indication on your camera to ensure correct date/time stamp on the video files. 1.Access the Advanced Settings list (see Connect Camera to Internet, described previously. 2.From the Advancd Settings list, scroll to Time Zone. 1 2 4 3 Loosen the wingnut to unlock the mounting post. Attach the camera to the mounting screw and turn it to the desired direction. Adjust the post to the correct angle, then tighten the wingnut to lock the post into place. Tighten the brace against the camera to secure it in place. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may c…

Text truncated - open the document above for the full version.

F441-WAPPGO1ISU-11-C7 40*25mm THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:(1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2)THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS DEVICE. UNIDEN AMERICA CORP. FCC ID:LE2APPCAM25HDA Input:5V 1500mA Model Number:APPCAM25HDA IC:4801A-APPCAM25HDA Model:APPCAM25HDA SN:H 00 0 00000

Label Location:

FCC ID: LE2APPCAM25HDA RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Test Result of RF Exposure Evaluation 802.11b mode Channel Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result Lowest (2412MHz) 52.84 0.01666 1.0 PASS Middle (2437MHz) 56.75 0.01789 1.0 PASS Highest (2462MHz) 58.21 0.01835 1.0 PASS 802.11g mode Channel Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result Lowest (2412MHz) 29.31 0.00924 1.0 PASS Middle (2437MHz) 38.02 0.01199 1.0 PASS Highest (2462MHz) 31.84 0.01004 1.0 PASS 802.11n(H20) mode Channel Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result Lowest (2412MHz) 28.64 0.00903 1.0 PASS Middle (2437MHz) 37.50 0.01182 1.0 PASS Highest (2462MHz) 31.55 0.00995 1.0 PASS 802.11n(H40) mode Channel Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result Lowest (2422MHz) 17.02 0.00537 1.0 PASS Middle (2437MHz) 19.63 0.00619 1.0 PASS Highest (2452MHz) 16.41 0.00517 1.0 PASS Remark: antenna gain=2.0 dBi

Global United Technology Services Co., Ltd. Report No.: GTSE15040043201 Authorized Signature: Robinson Lo Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the GTS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of GTS or testing done by GTS in connection with, distribution or use of the product described in this report must be approved by GTS in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. FCC Report (WIFI) Applicant: JSW Pacific Corporation Address of Applicant: 3F-3, No 700, Chung-Zweng Road Chung Ho City Taipei, Hsien Taiwan Equipment Under Test (EUT) Product Name: 720p WIFI Camera Model No.: APPCAM25HDA FCC ID: LE2APPCAM25HDA Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247:2014 Date of sample receipt: April 21, 2015 Date of Test: April 21-28, 2015 Date of report issued: April 28, 2015 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTSE15040043201 Global United Technology Services Co., Ltd. Project No.: GTSE150400432RF Room 301-309, 3th Floor, Block A, Huafeng Jinyuan Business Building, No. 300 Laodong Industrial Zone,Xixiang Road, Baoan District, Shenzhen 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 65 2 Version Version No. Date Description 00 April 28, 2015 Original Prepared By: Date: April 28, 2015 Project Engineer Check By: Date: April 28, 2015 Reviewer Report No.: GTSE15040043201 Global United Technology Services Co., Ltd. Project No.: GTSE150400432RF Room 301-309, 3th Floor, Block A, Huafeng Jinyuan Business Building, No. 300 Laodong Industrial Zone,Xixiang Road, Baoan District, Shenzhen 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 65 3 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 VERSION .................................................................................................................................................. 2 3CONTENTS .............................................................................................................................................. 3 4TEST SUMMARY ..................................................................................................................................... 4 5GENERAL INFORMATION ...................................................................................................................... 5 5.1CLIENT INFORMATION ......................................................................................................................... 5 5.2GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 5.3TEST MODE ........................................................................................................................................ 6 5.4DESCRIPTION OF SUPPORT UNITS ....................................................................................................... 6 5.5TEST FACILITY .................................................................................................................................... 7 5.6TEST LOCATION ................................................................................................................................. 7 6TEST INSTRUMENTS LIST ..................................................................................................................... 8 7TEST RESULTS AND MEASUREMENT DATA ...................................................................................... 9 7.1ANTENNA REQUIREMENT ..................................................................................................................... 9 7.2CONDUCTED EMISSIONS ................................................................................................................... 10 7.3CONDUCTED PEAK OUTPUT POWER .................................................................................................. 13 7.4CHANNEL BANDWIDTH ...................................................................................................................... 14 7.5POWER SPECTRAL DENSITY ............................................................................................................. 19 7.6BAND EDGES .................................................................................................................................... 24 7.6.1Conducted Emission Method ..................................................................................................... 24 7.6.2Radiated Emission Method ........................................................................................................ 27 7.7SPURIOUS EMISSION ......................................................................................................................... 32 7.7.1Conducted Emission Method ....................................................................................…

Text truncated - open the document above for the full version.

Radiated Emission Conducted Emission