LHJ-FE4NA0210FE4NA0210

FE4NA0210 OEM Manual and User Guide v 1.0 (to be used for certification) FCC ID: LHJ-FE4NA0210 IC: 2807E-FE4NA0210 Terms and Acronyms CDMA Code Division Multiple Access UMTS Universal Mobile Telecommunication System WCDMA Wideband Code Division Multiple Access LTE Long Term Evolution LTE-A LTE-Advanced GLONASS GLObalnaya NAvigatsionnaya Sputnikovaya Sistema GNSS Global Navigation Satellite System DCM-TCU Data Connectivity Module DRX Discontinuous Reception ES Engineering Sample FDD Frequency Division Duplex GPIO General Purpose Input Output GSM Global System for Mobile HU USB host HSIC High Speed Inter-Chip PCIe Peripheral Component Interconnect Express MP Mass Production NAD Network Access Device OEM Original Equipment Manufacturer PCB Printed Circuit Board PHY Physical Layer SIM Subscriber Identity Module TDD Time Division Duplex TSP Telematics Service Provider FE4NA0210 Module The FE4NA0210 NAD is a proprietary embedded module designed by Continental Automotive Systems, Inc. The modules will be integrated into Data Connectivity Modules (DCM-TCUs) or USB hosts (HUs) designed and produced by Continental or by a 3rd party for use by automotive OEMs. DCM-TCUs will be installed into vehicles during the OEM’s factory assembly process and will not be accessible without use of special tools. Primary use-cases are data-centric with data and voice connections to Telematics Service Providers (TSP). 1 Key Features Air Interface Support • LTE FDD: 3GPP Rel 14 • LTE FDD: DL Category-9 / UL Category-5 • UMTS: HSUPA CAT6 (up to 5.76-Mbps), HSPA CAT14 (up to 21-Mbps) or HSPA CAT24 (up to 42- Mbps) depending on configuration • VoLTE – HD Voice • Embedded Qualcomm GNSS Sub-system, Gen9v2 • GPS, Glonass, Beidou, Galileo Receiver • SBAS supported: EGNOS/MSAS/QZSS/WAAS/GAGAN • Able to track ~40 channels simultaneously 2 Regulatory Compliance Notes FCC: This device complies with Part 15, Part 22(H), Part 24(E) and Part 27 of the FCC Rules. The FCC ID for this device is LHJ-FE4NA0210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Industry of Canada: This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.” « Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. » This radio transmitter (2807E-FE4NA0210) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. « Le présent émetteur radio (2807E-FE4NA0210) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.». 3 Device Installation and User Manual The FE4NA0210 module is a proprietary product designed and manufactured by Continental Automotive Systems, Inc. for integration into telematics control units manufactured by Continental Automotive Systems, Inc. i. The module is limited to installation ONLY in an integrated device manufactured by Continental Automotive Systems, Inc. ii. During manufacturing process of the integrated device, the module is soldered onto the pcb of the integrated device. iii. The integrated device must provide RF connectors to external antennas or RF traces to connect the FE4NA0210 modules to antennas inside the integrated device. The typical reference design for the RF trace layout, including pcb stack-up and trace length is described in Section 6 of this document. iv. Automotive OEM is responsible for ensuring that the end-user has no manual instructions to remove or install module. v. The module is limited to installation in mobile applications, according to Part 2.1091(b). vi. No other operation configurations are allowed. vii. Changes or modifications to this system by other than a facility authorized by Continental could void authorization to use this equipment. viii. The module does not have a pre-defined antenna. Under No conditions may an antenna gain be used that would exceed the ERP and EIRP power limit as specified in Part 22, Part 24 and Part 27. ix. The integrator is responsible for fulfilling FCC and IC requirements for the integrated device. SAR is related to the final product’s implementation and should be assessed based on its proximity to human body. If Continental chooses to re-use modular approval, then the TCU shall be clearly labeled with an external label containing the integrated modem’s FCC ID. For example, the label can include text “Contains device with FCC ID: LHJ-FE4NA0210 and IC: 2807E-FE4NA0210”. 4 Antenna requirements for use with FE4NA0210 module: • The FE4NA0210 module is for use with external antennas ONLY. • For all standalone LTE/WCDMA operations the maximum antenna gain including cable loss shall not exceed the following values: o UMTS Band 2: 9.0 dBi o UMTS Band 4: 6.0 dBi o UMTS Band 5: 10.0 dBi o LTE Band 2: 9.0 dBi o LTE Band 4: 6.0 dBi o LTE Band 5: 10.0 dBi o LTE Band 12: 9.0 dBi o LTE Band 13: 9.0 dBi o LTE Band 14: 9.0 dBi o LTE Band 66: 6.0 dBi • For all collocated LTE/WCDMA operations the maximum ant…

Text truncated - open the document above for the full version.

Continental Automotive Systems, Inc. 21440 West Lake Cook Road, Deer Park, Illinois 60010, United States Tel: 8478622435 ; Fax: 847-8628016 Date: March 9, 2020 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for Confidentiality FCC ID: LHJ-FE4NA0210 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. ⚫ Schematic Diagram ⚫ Block Diagram ⚫ Part List ⚫ Operational Description ⚫ Tune-up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’ s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. ⚫ External Photos ⚫ Internal Photos ⚫ Test Setup Photos ⚫ User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, ______________________ James Zhang [email protected]

Continental Automotive Systems, Inc. 21440 West Lake Cook Road, Deer Park, Illinois 60010, United States Tel: 8478622435 ; Fax: 847-8628016 Date: March 9, 2020 Module Approval Checklist FCC ID: LHJ-FE4NA0210 Item Requirements EUT 1. The modular transmitter must have its own RF shielding. The module is equipped with its own shielding case. 2. The modular transmitter must have buffered modulation / data inputs. The module has buffer modulation / data inputs. 3. The modular transmitter must have its own power supply regulation. The module has its own power supply regulation. 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), Not applicable to licensed modules. 5. The modular transmitter must be tested in a stand-alone configuration. The module was tested on evaluation board, and it’s not inside of another device during testing 6. The modular transmitter must be labeled with its own FCC ID number. The module transmitter will be labeled with its own FCC ID, and for OEM integration the integration manual contains labeling instructions for the host device per Part 15.212 (vi) 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The module approved transmitter complies with all applicable rules and the integration manual contains any specific requirements addressed to the integrator and/or to the end-user of the final end-product. 8. The modular transmitter must comply with any applicable RF exposure requirement. The modular transmitter complies with RF exposure requirement. ______________________ James Zhang [email protected]

Continental Automotive Systems, Inc. 21440 West Lake Cook Road, Deer Park, Illinois 60010, United States Tel: 8478622435 ; Fax: 847-8628016 Date: March 9, 2020 To whom it may concern, Please be notified that I, James Zhang, have designated Jones Tsai in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Jones Tsai in Sporton International Inc. on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 862. This authorization is limited to the product of as following: FCC ID: LHJ-FE4NA0210 If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Should you have any questions or comments regarding this matter, please don’t hesitate to contact me. Sincerely yours, ______________________ James Zhang [email protected]

PHOTOGRAPHS OF EUT Report No.: EP031205 Brand Name: Continental / Model Name: FE4NA0210 TEL : 886-3-327-3456 Page Number : 1 of 5 FAX : 886-3-328-4978 Issued Date : Jul. 30, 2020 Report Version : 01 720510 1. External Photograph of EUT

FCC ID: LHJ-FE4NA0210; IC: 2807E-FE4NA0210 Figure 1: Label placed on top of the module. Label with FCC and IC ID information is placed on top of the module and is clearly visible.

PHOTOGRAPHS OF EUT Report No.: EP031205 Brand Name: Continental / Model Name: FE4NA0210 TEL : 886-3-327-3456 Page Number : 2 of 5 FAX : 886-3-328-4978 Issued Date : Jul. 30, 2020 Report Version : 01 2. Internal Photograph of EUT PHOTOGRAPHS OF EUT Report No.: EP031205 Brand Name: Continental / Model Name: FE4NA0210 TEL : 886-3-327-3456 Page Number : 3 of 5 FAX : 886-3-328-4978 Issued Date : Jul. 30, 2020 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP031205 Brand Name: Continental / Model Name: FE4NA0210 TEL : 886-3-327-3456 Page Number : 4 of 5 FAX : 886-3-328-4978 Issued Date : Jul. 30, 2020 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP031205 Brand Name: Continental / Model Name: FE4NA0210 TEL : 886-3-327-3456 Page Number : 5 of 5 FAX : 886-3-328-4978 Issued Date : Jul. 30, 2020 Report Version : 01 ─────THE END────

TEL : 886-3-327-3456 Page Number : 1 of 14 FAX : 886-3-328-4978 Issued Date : Jul. 27, 2020 Report Template No.: BU5-FD15B Version 2.5 Report Version : 01 FCC EMI TEST REPORT Report No. : FC031205 FCC EMI TEST REPORT FCC ID : LHJ-FE4NA0210 Equipment : FE4NA0210 Brand Name : Continental Model Name : FE4NA0210 Applicant : Continental Automotive Systems, Inc. 21440 W Lake Cook Rd. Manufacturer : Continental Automotive Systems, Inc. 21440 W Lake Cook Rd. Standard : FCC 47 CFR FCC Part 15 Subpart B Class B The product was received on Oct. 30, 2019 and testing was started from Oct. 30, 2019 and completed on Nov. 04, 2019. We, SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, would like to declare that the tested sample has been evaluated in accordance with the test procedures given in ANSI C63.4-2014 and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. Approved by: Louis Wu SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) TEL : 886-3-327-3456 Page Number : 2 of 14 FAX : 886-3-328-4978 Issued Date : Jul. 27, 2020 Report Template No.: BU5-FD15B Version 2.5 Report Version : 01 FCC EMI TEST REPORT Report No. : FC031205 Table of Contents History of this test report ................................................................................................................................. 3 Summary of Test Result................................................................................................................................... 4 1. General Description ................................................................................................................................... 5 1.1. Product Feature of Equipment Under Test ....................................................................................... 5 1.2. Product Specification of Equipment Under Test ............................................................................... 5 1.3. Modification of EUT ........................................................................................................................... 6 1.4. Test Location ..................................................................................................................................... 6 1.5. Applicable Standards ........................................................................................................................ 6 2. Test Configuration of Equipment Under Test ......................................................................................... 7 2.1. Test Mode ......................................................................................................................................... 7 2.2. Connection Diagram of Test System ................................................................................................ 7 2.3. Support Unit used in test configuration and system .......................................................................... 8 2.4. EUT Operation Test Setup ................................................................................................................ 8 3. Test Result .................................................................................................................................................. 9 3.1. Test of AC Conducted Emission Measurement ................................................................................ 9 3.2. Test of Radiated Emission Measurement ....................................................................................... 11 4. List of Measuring Equipment .................................................................................................................. 13 5. Uncertainty of Evaluation ........................................................................................................................ 14 Appendix A. AC Conducted Emission Test Result Appendix B. Radiated Emission Test Result Appendix C. Setup Photographs TEL : 886-3-327-3456 Page Number : 3 of 14 FAX : 886-3-328-4978 Issued Date : Jul. 27, 2020 Report Template No.: BU5-FD15B Version 2.5 Report Version : 01 FCC EMI TEST REPORT Report No. : FC031205 History of this test report Report No. Version Description Issued Date FC031205 01 Initial issue of report Jul. 27, 2020 TEL : 886-3-327-3456 Page Number : 4 of 14 FAX : 886-3-328-4978 Issued Date : Jul. 27, 2020 Report Template No.: BU5-FD15B Version 2.5 Report Version : 01 FCC EMI TEST REPORT Report No. : FC031205 Summary of Test Result Report Clause Ref Std. Clause Test Items Result (PASS/FAIL) Remark 3.1 15.107 AC Conducted Emission Pass Under limit 13.35 dB at 0.627 MHz 3.2 15.109 Radiated Emission Pass Under limit 13.13 dB at 948.590 MHz Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and Explanations: The declared of product specification for EUT presented in the report are provided by the manufacturer, and the manufacturer takes all the responsibilities for the accuracy of product specification. Reviewed by: Dara Chiu Report Producer: Amy Chen TEL : 886-3-327-3456 Page Number : 5 of 14 FAX : 886-3-328-4978 Issued Date : Jul. 27, 2020 Report Template No.: BU5-FD15B Version 2.5 Report Version : 01 FCC EMI TEST REPORT Report No. : FC031205 1. General Description 1.1. Product Feature of Equipment Under Test Product Feature Equipment FE4NA0210 Brand Name Continental Model Name FE4NA0210 FCC ID LHJ-FE4NA0210 EUT supports Radios application WCDMA/HSPA/LTE/GNSS HW Version FE4NA0210 EUT Stage Identical Prototype 1.2. Product Specification of Equipment Under Test Standards-related Prod…

Text truncated - open the document above for the full version.

TEL : 886-3-327-3456 Page Number : C1 of C3 FAX : 886-3-328-4978 FCC EMI TEST REPORT Report No. : FC031205 Appendix C. Setup Photographs <Conducted Emission> Mode 1 Remote View TEL : 886-3-327-3456 Page Number : C2 of C3 FAX : 886-3-328-4978 FCC EMI TEST REPORT Report No. : FC031205 Rear View TEL : 886-3-327-3456 Page Number : C3 of C3 FAX : 886-3-328-4978 FCC EMI TEST REPORT Report No. : FC031205 <Radiated Emission> Mode 2 LF HF ─────THE END─────