LKT-BULTRA-5BreezeULTRA

EMP5605H (ALVARION) High Power 5GHz 11n Mini-PCI Adapter 5GHz IEEE802.11a/n 2T2R 300Mbps High Performance Alvarion Ltd 21A HaBarzel Street Tel Aviv 69710 ISRAEL Tel: + 972-3-6456262 Fax: + 972-3-6456290 www.alvarion.com Package Contents 1 x MiniPCI Adapter (EMP5605H (ALVARION)) Alvarion miniPCI series radio modules perform extreme high power and economize the power consumption on the system platform. EMP5605H (ALVARION) is an 802.11a/n WiFi 2x2 mini-PCI module designed specifically for integration to maximum performance ratio. EMP5605H (ALVARION) delivers the ultimate wireless triple play experience for video, voice, and data transmission in the home, for the business, and on the road. With enhanced features on the ESD protection, industrial-based operating temperature, economized system power consumption, industrial-best sensitivity than normal module, MMCX connectors, and stable heating protection design, makes the module is easily to integrate into a wide range of any platform. Features Industrial-best sensitivity -90dBm@6Mbps, -72dBm@54Mbps, -89dBm@MCS0/MCS8, -70dBm@MCS7/MCS15 Supports IEEE 802.11a/802.11n Compatible among multiple wifi networks Enables bandwidth up to 300Mbps Fast throughput for 802.11a and 802.11n 2T2R design architecture Higher and greater reliable throughputs over range MMCX antenna connector Two MMCX connectors Specification Hardware Specification Standard WECA(WiFi & WiFi5 Compliance), IEEE802.11a/n, RoHS Chipset Atheros AR9220 Physical Interface 32-bit Mini-PCI Type III A 2 x MMCX Connector Power Requirements External DC power in supported, Voltage=5V Continuous [email protected] <1.7A Current Consumption Information Tx Current Consumption Continuous [email protected] <2A EMP5605H (ALVARION) High Power 5GHz 11n Mini-PCI Adapter 5GHz IEEE802.11a/n 2T2R 300Mbps High Performance Alvarion Ltd 21A HaBarzel Street Tel Aviv 69710 ISRAEL Tel: + 972-3-6456262 Fax: + 972-3-6456290 www.alvarion.com Rx Current Consumption Continuous Rx <600mA Card on Current Data Communicating with AP <450mA Sleep Current Sleep Mode <100mA RF Specification Frequency Band 802.11a 5.15 ~ 5.35GHz, 5.47 ~ 5.725GHz, 5.725~5.825GHz Data rate 300 Mbps Receive Sensitivity (Typical) 802.11n(20MHz) -89dBm @ MCS0/MCS8 -70dBm @ MCS7/MCS15 802.11n(40MHz) -86dBm @ MCS0/MCS8 -68dBm @ MCS7/MCS15 802.11a -90dBm @ 6Mbps -72dBm @ 54Mbps Available transmit power ( with external 5V power ) 802.11n ( ± ±± ± 2dBm ) 26dBm @ MCS0~1/MCS8~9 25dBm @ MCS2~3/MCS10~11 24dBm @ MCS4/MCS12 23dBm @ MCS5/MCS13 23dBm @ MCS6/MCS14 21dBm @ MCS7/MCS15 802.11a( ± ±± ± 2dBm ) 26dBm @ 6~24Mbps 25dBm @ 36Mbps 24dBm @ 48Mbps 23dBm @ 54Mbps Software Specification Security WPA, WPA2, 64/128 bits WEP, TKIP and AES Hardware-base IEEE 802.11i encryption engine Environment & Mechanical Temperature Range -30°C to 80°C Humidity (non-condensing) 0%～95% typical Dimensions 66mm (L) x 59.5mm (W) x 5mm (H) Weight 16g Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 165cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) Due to the facts that this module has high built-in output power and with a high gain direction antenna, the module can be used in a professional installed end product only. The final product must be professional installed to make sure that 165 cm can be maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a se…

Text truncated - open the document above for the full version.

Alvarion Ltd 21A HaBarzel Street Tel Aviv 69710 ISRAEL Tel: + 972-3-6456262 Fax: + 972-3-6456290 www.alvarion.com Date:2012-01-06 Declaration for no non-US channel operation We, Alvarion Ltd., declare that the device does not support any non-US channels in all the operational mode(s) for the following product. FCC ID: LKT-BULTRA-5 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- Moti Ezra/Certificaiton & Qualification Alvarion Ltd. TEL: 972-3-7674-314 FAX: 972-3-6456-222 E-mail: [email protected]

Date:2012-01-10 FCC ID: LKT-BULTRA-5 IC ID: 2514A-BULTRA5 Professional Installation Attestation To Whom It May Concern: Please be advised that due to the unique Market and function targeted by this product, this product will need special trained professional in configuring and installing the product. We hereby declare that the product will be distributed through controlled distribution channel which has special trained professional to install this product and will not be sold directly to the general public through retail store. Yours sincerely, __________________________________________ Moti Ezra/Certification & Qualification Alvarion Ltd. TEL: 972-3-7674-314 FAX: 972-3-6456-222 E-mail: [email protected] Alvarion Ltd 21A HaBarzel Street Tel Aviv 69710 ISRAEL Tel: + 972-3-6456262 Fax: + 972-3-6456290 www.alvarion.com

Alvarion Ltd 21A HaBarzel Street Tel Aviv 69710 ISRAEL Tel: + 972-3-6456262 Fax: + 972-3-6456290 www.alvarion.com Date: 2012-01-06 FCC ID: LKT-BULTRA-5 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, __________________________________ Moti Ezra/Certificaiton & Qualification Alvarion Ltd. TEL: 972-3-7674-314 FAX: 972-3-6456-222 Alvarion Ltd 21A HaBarzel Street Tel Aviv 69710 ISRAEL Tel: + 972-3-6456262 Fax: + 972-3-6456290 www.alvarion.com E-mail: [email protected]

Alvarion Ltd 21A HaBarzel Street Tel Aviv 69710 ISRAEL Tel: + 972-3-6456262 Fax: + 972-3-6456290 www.alvarion.com A G E N C Y A U T H O R I Z A T I O N L E T T E R FCC ID: LKT-BULTRA-5 Date: 2012.01.06 To whom it may concern: We, the undersigned, hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by BV CPS Taoyuan within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months from original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, ___________________________ Moti Ezra/Certificaiton & Qualification Alvarion Ltd. TEL: 972-3-7674-314 FAX: 972-3-6456-222 E-mail: [email protected]

FCC ID: LKT-BULTRA-5 Report No.: RF110519C13 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch January 10, 2012 Dear Application Examiner, Alvarion Ltd., It’s a module. FCC ID: LKT-BULTRA-5 would like to have your authorization as a modular approval. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data input, it is integrated in chip AR9220. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is ZT7103. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: LKT-BULTRA-5 Report No.: RF110519C13 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Gary Chang Technical Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

Page 3 Page 4 Page 5 Page 6 Page 7

Report No.: SA110322C09 Report Format Version 4.0.0 1 RF EXPOSURE REPORT REPORT NO.: SA110322C09 MODEL NO.: BU/RB-B350-5X-P6000, BU/RB-B600-5X-P6000, BU/RB-B350D-5X-P6000, BU/RB-B350D-5X-LX-P6000, BU/RB-B600D-5X-P6000, AU-E-SA-5X-1S-M7000, AU-E-SA-5X-2S-M7000, AU-E-SA-5X-3S-M7000, BU/RB-B600 AU-E-5X-1S, BU/RB-B350 AU-E-5X-2S FCC ID: LKT-BULTRA-5 RECEIVED: Mar. 22, 2011 TESTED: Nov. 07 ~ Dec. 20, 2011 ISSUED: Dec. 22, 2011 APPLICANT: Alvarion Ltd. ADDRESS: 21a HaBarzel St. Tel Aviv 69710, Israel ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 6 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval, or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA110322C09 Report Format Version 4.0.0 2 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................. 4 2. RF EXPOSURE............................................................................................................... 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE)......................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................... 5 2.3 CLASSIFICATION ........................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER.................................. 6 Report No.: SA110322C09 Report Format Version 4.0.0 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Dec. 22, 2011 Report No.: SA110322C09 Report Format Version 4.0.0 4 1. CERTIFICATION PRODUCT:BreezeULTRA MODEL:BU/RB-B350-5X-P6000, BU/RB-B600-5X-P6000, BU/RB-B350D-5X-P6000, BU/RB-B350D-5X-LX-P6000, BU/RB-B600D-5X-P6000, AU-E-SA-5X-1S-M7000, AU-E-SA-5X-2S-M7000, AU-E-SA-5X-3S-M7000, BU/RB-B600 AU-E-5X-1S, BU/RB-B350 AU-E-5X-2S BRAND:Alvarion APPLICANT:Alvarion Ltd. TESTED:Nov. 07 ~ Dec. 20, 2011 TEST SAMPLE:ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: AU-E-SA-5X-1S-M7000) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Dec. 22, 2011 Andrea Hsia / Specialist APPROVED BY : , DATE:Dec. 22, 2011 Gary Chang / Technical Manager Report No.: SA110322C09 Report Format Version 4.0.0 5 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 165cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA110322C09 Report Format Version 4.0.0 6 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MODULATION MODE MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 802.11a -3.7 23 165 0.0002 1 802.11n (20MHz) -4.0 23 165 0.0002 1 5180-5240 802.11n (40MHz) -0.1 23 165 0.0006 1 802.11a 29.9 23 165 0.575 1 802.11n (20MHz) 29.8 23 165 0.561 1 5745-5825 802.11n (40MHz) 29.8 23 165 0.560 1 802.11a 26.9 28 165 0.906 1 802.11n (20MHz) 27.0 28 165 0.916 1 5745-5825 802.11n (40MHz) 27.3 28 165 0.993 1

Report No.: RF110322C09 1 Report Format Version 4.0.0 FCC TEST REPORT (15.247) REPORT NO.: RF110322C09 MODEL NO.: AU-E-SA-5X-1S-M7000 (refer to item 3.1 for more detail) FCC ID: LKT-BULTRA-5 RECEIVED: Mar. 22, 2011 TESTED: Nov. 07 ~ Dec. 20, 2011 ISSUED: Dec. 22, 2011 APPLICANT: Alvarion Ltd. ADDRESS: 21a HaBarzel St. Tel Aviv 69710, Israel ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 63 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF110322C09 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.............................................................................................. 4 1. CERTIFICATION........................................................................................................... 5 2. SUMMARY OF TEST RESULTS .................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ............................................................................... 6 3. GENERAL INFORMATION ........................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................. 7 3.2 DESCRIPTION OF TEST MODES ............................................................................... 8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 9 3.2.2 DESCRIPTION OF SUPPORT UNITS ......................................................................... 9 3.2.3 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................. 10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................ 12 4. TEST TYPES AND RESULTS .................................................................................... 13 5. TEST TYPES AND RESULTS .................................................................................... 13 5.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT..................................... 13 5.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................. 13 5.1.2 TEST INSTRUMENTS................................................................................................ 14 5.1.3 TEST PROCEDURES ................................................................................................ 15 5.1.4 DEVIATION FROM TEST STANDARD....................................................................... 15 5.1.5 TEST SETUP.............................................................................................................. 16 5.1.6 EUT OPERATING CONDITIONS ............................................................................... 16 5.1.7 TEST RESULTS ......................................................................................................... 17 5.2 CONDUCTED EMISSION MEASUREMENT ............................................................. 37 5.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................... 37 5.2.2 T EST INSTRUMENTS............................................................................................... 37 5.2.3 TEST PROCEDURES ................................................................................................ 38 5.2.4 DEVIATION FROM TEST STANDARD....................................................................... 38 5.2.5 TEST SETUP.............................................................................................................. 39 5.2.6 EUT OPERATING CONDITIONS ............................................................................... 39 5.2.7 TEST RESULTS ......................................................................................................... 40 5.3 6dB BANDWIDTH MEASUREMENT.......................................................................... 44 5.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ....................................................... 44 5.3.2 TEST SETUP.............................................................................................................. 44 5.3.3 TEST INSTRUMENTS................................................................................................ 44 5.3.4 TEST PROCEDURE................................................................................................... 44 5.3.5 DEVIATION FROM TEST STANDARD....................................................................... 44 5.3.6 EUT OPERATING CONDITIONS ............................................................................... 44 5.3.7 TEST RESULTS ......................................................................................................... 45 5.4 CONDUCTED OUTPUT POWER............................................................................... 47 5.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT ............................... 47 5.4.2 TEST SETUP.............................................................................................................. 47 5.4.3 INSTRUMENTS .......................................................................................................... 47 5.4.4 TEST PROCEDURES ................................................................................................ 47 5.4.5 DEVIATION FROM TEST STANDARD....................................................................... 47 5.4.6 EUT OPERATING CONDITIONS ........…

Text truncated - open the document above for the full version.

Report No.: RF110322C09-1 1 Report Format Version 4.0.0 FCC TEST REPORT (15.407) REPORT NO.: RF110322C09-1 MODEL NO.: AU-E-SA-5X-1S-M7000 (refer to item 3.1 for more detail) FCC ID: LKT-BULTRA-5 RECEIVED: Mar. 22, 2011 TESTED: Nov. 07 ~ Dec. 20, 2011 ISSUED: Dec. 22, 2011 APPLICANT: Alvarion Ltd. ADDRESS: 21a HaBarzel St. Tel Aviv 69710, Israel ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 49 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF110322C09-1 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.............................................................................................. 4 1. CERTIFICATION........................................................................................................... 5 2. SUMMARY OF TEST RESULTS .................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY................................................................................ 6 3. GENERAL INFORMATION ........................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................. 7 3.2 DESCRIPTION OF TEST MODES ............................................................................... 8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 9 3.2.2 DESCRIPTION OF SUPPORT UNITS ......................................................................... 9 3.2.3 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................. 10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................ 12 4. TEST TYPES AND RESULTS .................................................................................... 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT..................................... 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................. 13 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS .............. 13 4.1.3 TEST INSTRUMENTS................................................................................................ 14 4.1.4 TEST PROCEDURES ................................................................................................ 15 4.1.5 DEVIATION FROM TEST STANDARD....................................................................... 15 4.1.6 TEST SETUP.............................................................................................................. 16 4.1.7 EUT OPERATING CONDITION.................................................................................. 16 4.1.8 TEST RESULTS ......................................................................................................... 17 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................. 26 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................... 26 4.2.2 TEST INSTRUMENTS................................................................................................ 26 4.2.3 TEST PROCEDURES ................................................................................................ 27 4.2.4 DEVIATION FROM TEST STANDARD....................................................................... 27 4.2.5 TEST SETUP.............................................................................................................. 28 4.2.6 EUT OPERATING CONDITIONS ............................................................................... 28 4.2.7 TEST RESULTS ......................................................................................................... 29 4.3 MAXIMUM CONDUCTED OUTPUT POWER MEASUREMENT ............................... 31 4.3.1 LIMITS OF MAXIMUM CONDUCTED OUTPUT POWER MEASUREMENT............. 31 4.3.2 TEST SETUP.............................................................................................................. 31 4.3.3 TEST INSTRUMENTS................................................................................................ 31 4.3.4 TEST PROCEDURE................................................................................................... 32 4.3.5 DEVIATION FROM TEST STANDARD....................................................................... 32 4.3.6 EUT OPERATING CONDITIONS ............................................................................... 32 4.3.7 TEST RESULTS ......................................................................................................... 33 4.4 PEAK POWER EXCURSION MEASUREMENT ........................................................ 35 4.4.1 LIMITS OF PEAK POWER EXCURSION MEASUREMENT...................................... 35 4.4.2 TEST SETUP.............................................................................................................. 35 4.4.3 TEST INSTRUMENTS................................................................................................ 35 4.4.4 TEST PROCEDURE................................................................................................... 35 4.4.5 DEVIATION FROM TEST STANDARD....................................................................... 35 4.4.6 EUT OPERATING CONDITIONS ............................................................................... 35 4.4.7 TEST RESUL…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST For 23dBi antenna 2 3 For 28dBi antenna 4 5 RADIATED EMISSION TEST For 23dBi antenna 6 7 For 28dBi antenna 8