LSQ-IDEU-830-4Intelligent Data Extension Unit - Repeater

Home Unit Installation and Operation Guide Information in this documentation is subject to change without notice and does not represent a commitment on part of Elmo-Tech Ltd. The software described in this document is subject to the license agreement that is included with the product, which specifies the permitted and prohibited uses of the product. Any unauthorized duplication or use of this documentation, in whole or in part, in print, or in any other storage or retrieval system is prohibited. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means for any purpose other than the purchaser’s personal use without the permission of Elmo-Tech Ltd. © 2002-10 Elmo-Tech Ltd. All rights reserved. Unless otherwise noted, all names of companies, products, street addresses, and persons contained herein are part of a completely fictitious scenario and are designed solely to document the use of an Elmo-Tech product. Contact Us Corporate Headquarters Elmo-Tech Ltd. 2 Ha-Barzel St., P.O. Box 13236, 61132 Tel Aviv, Israel Tel: 972-3-7671800 Fax: 972-3-7671801 U.S.A Customers, call 1-800-313-1483 E-mail: [email protected] Visit us at: www.elmotech.com Table of Contents 1 Getting Started ............................................................... 3 About This Manual ............................................................ 3 2 Installation & Activation Instructions ............................. 5 Locating the Home Unit ..................................................... 6 Activating the Home Unit ................................................... 6 3 Maintaining & Packing the Monitoring Equipment ........... 9 Cleaning the Home Unit ..................................................... 9 4 FCC Information ............................................................ 10 i STaR Unit & Transmitter Installation and Operation Guide ii List of Figures Figure 1 Home Unit ....................................................................5 Figure 2 Locating the Home Unit ..................................................6 1 Getting Started About This Manual The Home Unit Installation and Operation Guide has been created for the installation expert and is meant as a guide through the installation and operational procedures. This manual assumes that you have at least some experience with electronic monitoring systems. This manual does not contain information regarding system settings, configuration or any other software produced by Elmo-Tech Ltd., unless directly related to this produce. Please refer to the appropriate manuals for information with respect to the E3-MWS Monitor Operator and System Administration manuals. All related hardware and software must be installed and repaired by a qualified Elmo-Tech customer service representative or an experienced system administrator. Elmo-Tech Ltd is committed to innovation and continued improvement. Upgrades may be announced that consist of software improvements and updated manuals will generally accompany those system changes. 3 2 Installation & Activation Instructions Figure 1 Home Unit 5 1Track Home Unit Installation and Operation Guide Locating the Home Unit Place the Home Unit as close to the center of the curfew location as possible, 3 ft (1 m) off the ground and at least 1 foot (30 cm) away from the wall. Figure 2 Locating the Home Unit Activating the Home Unit To activate the Home Unit: Connect the adapter end of the external power cable to the power outlet. The Home Unit makes three audible beeping sounds. The Charge LED on the front panel flashes when the Home Unit is first activated. 6 1Track Home Unit Installation and Operation Guide 7 The Charge and Power LED’s light up only after the backup battery is fully charged. The Home Unit is now in monitoring mode. To deactivate the Home Unit: 1. Using a screwdriver, unscrew and remove the Unit holding screw located on the underside of the mounting bracket. 2. Disconnect the Home Unit from the mounting bracket by pulling the Unit upwards slightly. 3. Remove the Home Unit from the mounting bracket and turn the Unit over. The deactivation button is located on the backside of the Unit. 4. Using a pointed instrument (but not sharp), push down on the reset button. The Home Unit deactivates itself and all stored information is deleted. 3 Maintaining & Packing the Monitoring Equipment Regular cleaning of your Elmo-Tech equipment is recommended, using Elmo-Tech approved products. After cleaning, Elmo-Tech recommends that you perform a visual inspection of all Units to check for cracks or any other damage, before redeploying into the field Cleaning the Home Unit To clean the Home Unit: 1. Remove the Unit from its carrying case. 2. Spray the surface of the Unit with an alcohol based cleaner (optional). Note Elmo-Tech recommends Citrus Base cleaner by 3M™ (http://solutions.3m.com/). 3. Using a damp cloth, wipe the outside of the Unit. Caution: Do not, under any circumstances, submerge or place the Unit under running water. 4. Using a dry cloth, or paper towel, dry the outside of the Unit. 5. Once the Unit is dry, return it to its carrying case. 9 10 4 FCC Information FCC ID: LSQ-IDEU-830-4 FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT The equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may …

Text truncated - open the document above for the full version.

LSQ-IDEU-830-4 Block Diagram The following block diagram illustrates the functional areas within the LSQ-IDEU-830-4 Intelligent Data Extension Unit. Transceiver CC1101 CPU PIC18F86J11T-I/PT SPI nIRQ GPIO2 Battery sensor SPI Serial EEPROM Charger External DC Power 12V Battery 3.6V LDO regulator 3.0V Helical Antenna VCC VCC VCC Crystal (26MHz) Crystal (14.7456MHz)

FCC Confidentiality Form 26.1.10 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen, This letter is to comply with Section 0.457(d)(2)(i) and 0.459 pertaining to confidential material. Elmo Tech would like the following documents regarding this submission for FCC ID: LSQ-IDEU-830-4 to be kept confidential. • Permanent Confidentiality: Schematics • Short-term Confidentiality (180 days): Installation Manual The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want this document to be accessible to the general public. Sincerely, Gil Gemer CTO

IDEU-830-4 External Photographs Figure 1: IDEU-830-4 (Front) Figure 2: IDEU-830-4 (Back) Figure 3: IDEU-830-4 (Top) Figure 4: IDEU-830-4 (Bottom) Figure 5: IDEU-830-4 (Right) Figure 6: IDEU-830-4 (Left)

Label Location LSQ-IDEU-830-4

IDEU-830-4 Internal Photographs RF Antenna Figure 1: IDEU-830-4 (Open) Figure 2: PCB (Top) Figure 3: PCB (Rear)

IDEU-830-4 Intelligent Data Extension Unit Operational Description The iDEU-830-4 is a wall or table-top mounted device for use in various offender presence monitoring applications. The unit is primarily, but not exclusively, designed as a repeater to extend the range of bracelet tags attached to the ankle of the person monitored by the system. Transmissions received by the iDEU-830-4 are forwarded to a home unit installed at the offender’s home. Violations to the offender's curfew schedule generate events that are uploaded to the central monitoring station via various communication interfaces. When a transmission is received that is addressed specifically to the iDEU (i.e. it includes the iDEU’s ID), the transmission is handled by the iDEU as required. Handling the transmission could mean answering the source of the transmission or, alternatively, forwarding the data to a home unit. If a received transmission is not recognized, the transmission is discarded and no further action is taken by the iDEU. If simultaneous transmissions are sent to the iDEU, the strongest transmission is received and handled. The maximum transmission time does not exceed 10msec. The iDEU-830-4 comprises a 418MHz RF transceiver and an integral helical antenna. The unit is powered by a 100-240VAC to 12VDC power adapter and includes a 3.6V backup battery.

Test Report No. 9012300934 Applicant: ElmoTech Ltd. Equipment Under Test: Repeater Model: iDEU-830-4 FCC ID: LSQ-IDEU-830-4 From The Standards Institution Of Israel Industry Division Electronics & Telematics Laboratory EMC Section ACLASS Accreditation Services Test Report No.: 9012300934 Page 1 of 25 pages Title: Test on Repeater FCC ID: LSQ-IDEU-830-4 Model: iDEU-830-4 Description of Equipment Under Test (EUT): Repeater Model: iDEU-830-4 Serial Number: 1209 Software version 5.1 Hardware version 1.2 Manufactured by: Elmotech Ltd Reference Documents: ™ CFR 47 FCC: Rules and Regulations; Part 15. “Radio frequency devices”; Subpart C : “Intentional radiators” (2007), Section 15.205. “Restricted bands of operations”, Section 15.209. “Radiated emission limits, general requirements”. “Radiated Emission Limits, Additional Provisions”; Section 15.231. “Periodic operation in the bands 40.66 – 40.70 MHz, and above 70 MHz”. This Test Report contains 25 pages and may be used only in full. This Test Report applies only to the specimen tested and may not be applied to other specimens of the same product. Applicant: Elmotech Ltd. Address: 2 Habarzel Street, POB 13236, Tel-Aviv, Israel Sample for test selected by: The customer The date of test: 11, 13 January 2010 Test Report No.: 9012300934 Page 2 of 25 pages Title: Test on Repeater FCC ID: LSQ-IDEU-830-4 Model: iDEU-830-4 Table of Contents 1. EUT Description and operation 3 1.1. General description: 3 2. Test summary 5 2.1. Potential emission sources: 8 2.2. EUT setup and operation: 8 3. Measurements, examinations and derived results 8 3.1. Location of the Test Site: 8 3.2. Test condition: 8 3.3. Initial visual check and functional test: 8 3.4. Radiated emission test. 9 3.5. Common conditions for operation in the band above 70MHz. 10 3.6. Test of field strength emission from intentional radiator. 11 3.7. Test of occupied bandwidth per 15.231(c) 19 3.8. Test of conducted emission at main terminal. 20 4. Appendix 1. Test equipment used 22 5. Appendix 2: Antenna Factor and Cable Loss 23 Test Report No.: 9012300934 Page 3 of 25 pages Title: Test on Repeater FCC ID: LSQ-IDEU-830-4 Model: iDEU-830-4 1. EUT Description and operation 1.1. General description: * Note: the customer supplied all information in clause below. The iDEU-830-4 is a wall or table-top mounted device for use in various offender presence monitoring applications. The unit is primarily designed as a repeater to extend the range of bracelet transmitters attached to the ankle of the person monitored by the system. Transmissions received by the iDEU-830-4 are forwarded to a home unit installed at the offender’s home. Violations to the offender's curfew schedule generate events that are uploaded to the central monitoring station via various communication interfaces. Declare maximum EIRP power: -2 dBm@ 418 MHz Type of modulation: GFSK Antenna type: Helical antenna Power source: External AC/DC 12V power supply ElmoTech model SE 120100 and internal redundancy 3.6 Volt Li-Ion battery. The EUT’s block diagram is shown in Figures 1 External and internal views are presented in Photo #1. Test Report No.: 9012300934 Page 4 of 25 pages Title: Test on Repeater FCC ID: LSQ-IDEU-830-4 Model: iDEU-830-4 Transceiver CC1101 CPU PIC18F86J11T-I/PT SPI nIRQ GPIO2 Battery sensor SPI Serial EEPROM Charger External DC Power 12V Battery 3.6V LDO regulator 3.0V Helical Antenna VCC VCC VCC Crystal (26MHz) Crystal (14.7456MHz) Figure 1. Repeater block diagram. 3 m distance EUT Figure 2. Radiated emission test setup diagram. Test Report No.: 9012300934 Page 5 of 25 pages Title: Test on Repeater FCC ID: LSQ-IDEU-830-4 Model: iDEU-830-4 2. Test summary Parameter FCC Part 15 Reference paragraph Comply/not comply with the requirements Radiated emission test. Subpart C Section 15.209 Comply Test of field strength emission from intentional radiators “Radiated Emission Limits, Additional Provisions”; Section 15.231(b). Comply Occupied bandwidth Subpart C Section 15.231(c) Comply Conducted emission test Subpart C Section 15.207(a) Comply Telematics Laboratory January 2010 Name: Eng. Yuri Rozenberg Name: Michael Feldman Position: Head of EMC Branch Position: Test Technician Test Report No.: 9012300934 Page 6 of 25 pages Title: Test on Repeater FCC ID: LSQ-IDEU-830-4 Model: iDEU-830-4 Photo 1. EUT’s external and internal view Test Report No.: 9012300934 Page 7 of 25 pages Title: Test on Repeater FCC ID: LSQ-IDEU-830-4 Model: iDEU-830-4 Photo 2. Spurious emissions test setup. Photo 3. Spurious emissions investigation test setup. Test Report No.: 9012300934 Page 8 of 25 pages Title: Test on Repeater FCC ID: LSQ-IDEU-830-4 Model: iDEU-830-4 2.1. Potential emission sources: The potential emission sources are detailed in Table 1. Table 1. Potential emission sources Frequency Location 14.7456 MHz crystal CPU PIC18F86J11 26.0 MHz crystal Transceiver CC1101 418 MHz RF signal Base unit 2.2. EUT setup and operation: Respective tests were performed in Transmission (Tx) and Receive modes. Measurements of transmitter were performed in continue transmition mode. 3. Measurements, examinations and derived results 3.1. Location of the Test Site: Preliminary radiated test was conducted at the EMC laboratory of the Standards Institution of Israel in Tel-Aviv. Final tests were conducted in an Open Area Test Site located at Kibbutz Native Halamed Hai in Emek HaEla, Israel. 3.2. Test condition: Temperature: 20 °C. Humidity: 57 %. Atmospheric pressure: 1009 mbar. 3.3. Initial visual check and functional test: Initial visual check and brief built- in- test of the EUT was performed before testing. - No external damages were found. - The test on the EUT passed successfully. Test Report No.: 9012300934 Page 9 of 25 pages Title: Test on Repeater FCC ID: LSQ-IDEU-830-4 Model: iDEU-830-4 3.4. Radiated emission test. 3.4.1. General: Per FCC Part 15 Subpart C Sections 15.209, 15.231. ’ Initial scans were made using a peak detector but still using the appropriat…

Text truncated - open the document above for the full version.

IDEU-830-4 Test Setup Photographs