M4Y-SP230802.11 ac Wave 2 Access Point

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Page i Revision: 3.3.0.4 SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG 58-140007-IQN _V1.0 Page 1 Package Contents One access point One clamp Two waterproof cable glands One ground wire One mounting bracket + Four screws Note: SP230 and SP230-S5 both provides two waterproof cable glands. Installation Requirements TERMS OF USE: All Ethernet cabling runs must use CAT5e, 24 AWG (or above) Shielded Twisted Pair (STP) cabling. In addition, please cut the cable into a proper length, strip the cables on both ends, and crimp the wires into RJ45 connectors. It is the professional installer’s responsibility to follow local country regulations, including operation within legal frequency channels, output power, indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements. Mounting the Access Point on the Pole  Attach the mounting bracket to the device using four screws (included in the packaging). Securely tighten the screws.  Attach the clamp to encircle pole and the mounting bracket. Securely tighten the clamp. Note: Please avoid having obstacles or metal plates surround the access point. SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG 58-140007-IQN _V1.0 Page 2 Two-dimensional Mounting Kit (Optional accessory_SP-MKM5) Pole-Mount  Attach the intermediate steel plate to the device using four M5 screws (included in the packaging). Securely tighten the screws.  Attach the two-dimensional mounting bracket to the intermediate steel plate using four M4 screws (included in the packaging). Securely tighten the screws.  Attach the pole-supported bracket and align the area where the flat head screws will be attached. Insert two flat head screws into two-dimensional mounting bracket, and tighten them approximately. Note: The pole-supported bracket can accommodate up to 6 cm (2.36”) in diameter. Wall-Mount  Separate it into two parts: half-mounting bracket and M-type bracket and unscrew four hex head machine bolts on the two- dimensional mounting bracket.  Attach the intermediate steel plate to the device using four M5 screws (included in the packaging). Securely tighten the screws.  Attach half-mounting bracket to the device with intermediate steel plate using four M4  Attach M-type bracket to the device onto the wall, using four M5 screws + screw anchors SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG 58-140007-IQN _V1.0 Page 3 screws (included in the packaging). Securely tighten the screws. (included in the packaging). Securely tighten the screws.  Attach half-mounting bracket to the M-type bracket, then screw four hex head machine bolts. Securely tighten the screws. Anti-theft Steel Rope (Optional accessory_SP-CBM5)  Insert three anti-theft screws (included in the packaging) to the device through the mounting bracket. Securely tighten these three screws. Attach the clamp to encircle pole and the mounting bracket. Securely tighten the clamp.  Firstly, encircle the Anti-theft steel rope as following left diagram, then encircle on the pole. Secondly, insert the last anti-theft screw (included in the packaging) to the device with anti-theft steel rope. Securely tighten the screw. SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG 58-140007-IQN _V1.0 Page 4 Grounding Connection & Protect from Lightning 1. Make your device GND port connect to ground wire. 2. The ground wire connects to the earth. In addition, the grounding wire meets to 6-AWG copper grounding wire. Safety Notice 1. Do not install the device close to any electrical grounding device or lightning protection system. Place the device’s own grounding and lightning protection system apart from any electrical grounding device and lightning protection system as far as possible. 2. Protect components from electrostatic discharge: Please wear an ESD wrist strap or handle the power adapter by its edge and do not touch any component or printed circuit boards, especially for module device. 3. Make sure to keep the temperature and humidity of the installation location at an optimal level. 4. An excellent grounding system guarantees the stable operation of device, as well as to protect device from lightning, interference and electrostatic discharges. 5. Supply stable power to the device. Unstable power may cause the device to malfunction. The device supports PoE power supply and is recommended if the device is installed near grid lines within less than 100 meters radius. Installing a Waterproof Cable Gland for Ethernet Port (Optional accessory_ SP-WP-CM20)  Dismantle all the components of waterproof cable gland, and plug the cable through it. Thread and assemble one by one: (1) sealing nut (2) plastic ring (3) rubber (4) locking nut. Securely tighten all the components. Note: Be sure that grounding is available and that it must comply with local and national electrical codes. For additional lightning protection, use lightning rods and lightning arrestors. SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG 58-140007-IQN _V1.0 Page 5 Powering the Access Point Connect the PoE cable into the WAN/PoE IN port of the device. Warning: Do NOT attempt to connect any non-PoE devices to LAN port and make sure the input power should comply with PoE Out standard. LED Indicator Color Behavior Description Red Steady Initializing Flashing Power / system on Green Steady Internet connection detected Flashing No internet connection detected Access Point Configuration The SP230 default AP mode is TAP mode, which obtains IP addresses from DHCP Option 43 protocol. The SP230-S5 is FAP mode. Note: In TAP mode, the AP must be able to go with wireless LAN controllers (WLCs) for bulk configuration and performing other commands of access points. Please refer to WLC QSG for settings first, then go back to finish the AP configuration. https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=49 Step 1. Power on the AP. As the status o…

Text truncated - open the document above for the full version.

Z-Com, Inc. 5F, No.8, HSIN ANN RD., HSINCHU SCIENCE PARK, HSINCHU, 30078 TAIWAN Date: 2021/2/22 FCC ID: M4Y-SP230 Declaration Letter We, Z-Com, Inc. declare that the device will enable only WLAN 2.4G & 5G function through the applicant’s proprietary firmware and is not user changeable. If you have any questions regarding the authorization, please do not hesitate to contact us. Thank you! ----------------------------------- Jeff Jiang / Compliance Engineer Tel: +886 3 5777 364, Ext 153 Fax: +886 3 5773395 E-mail: [email protected]

Z-C om, Inc. 5F, No.8, HSIN ANN RD., HSINCH SCIENCE PARK, HSINCHU, 30078 TAIWAN Date: 2021-01-25 FCC ID: M4Y-SP230 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Jeff Jiang / Compliance Engineer Tel: +886 3 5777 364, Ext 153 Fax: +886 3 5773395 E-mail: [email protected] 5F, No.8, HSIN ANN RD., HSINCHU SCIENCE PARK, HSINCHU, 30078 TAIWAN

Z-C om, Inc. 5F, No.8, HSIN ANN RD., HSINCH SCIENCE PARK, HSINCHU, 30078 TAIWAN Date: 2021-02-22 FCC ID: M4Y-SP230 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 30 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- Jeff Jiang /Compliance Engineer Tel: +886 3 5777 364, Ext 153 Fax: +886 3 5773395 E-mail: [email protected] 5F, No.8, HSIN ANN RD., HSINCHU SCIENCE PARK, HSINCHU, 30078 TAIWAN

Z-Com, Inc. 5F, No.8, HSIN ANN RD., HSINCH SCIENCE PARK, HSINCHU, 30078 TAIWAN Date: 2021-01-25 FCC ID: M4Y-SP230 AUTHORIZATION LETTER To Whom It May Concern: Z-Com, Inc. hereby authorizes Amanda Wu, Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu, Senior Specialist of BV CPS Taoyuan on Z-Com, Inc.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- Jeff Jiang / Compliance Engineer Z-Com, Inc. Tel: +886 3 5777 364, Ext 153 Fax: +886 3 5773395 E-mail: [email protected] 5F, No.8, HSIN ANN RD., HSINCHU SCIENCE PARK, HSINCHU, 30078 TAIWAN

Reference No.: BDMW-WTW-P20121069-1 Page 1/8 CONSTRUCTION PHOTOS OF EUT Model: SP230-S5 Reference No.: BDMW-WTW-P20121069-1 Page 2/8 Reference No.: BDMW-WTW-P20121069-1 Page 3/8 Reference No.: BDMW-WTW-P20121069-1 Page 4/8 Reference No.: BDMW-WTW-P20121069-1 Page 5/8 Model: SP230 Reference No.: BDMW-WTW-P20121069-1 Page 6/8 Reference No.: BDMW-WTW-P20121069-1 Page 7/8 Reference No.: BDMW-WTW-P20121069-1 Page 8/8 Ground Cable

Reference No.: BDMW-WTW-P20121069-2 Page 1/26 CONSTRUCTION PHOTOS OF EUT Model: SP230-S5 Reference No.: BDMW-WTW-P20121069-2 Page 2/26 Reference No.: BDMW-WTW-P20121069-2 Page 3/26 Reference No.: BDMW-WTW-P20121069-2 Page 4/26 Reference No.: BDMW-WTW-P20121069-2 Page 5/26 Reference No.: BDMW-WTW-P20121069-2 Page 6/26 Reference No.: BDMW-WTW-P20121069-2 Page 7/26 Reference No.: BDMW-WTW-P20121069-2 Page 8/26 Reference No.: BDMW-WTW-P20121069-2 Page 9/26 Reference No.: BDMW-WTW-P20121069-2 Page 10/26 2G0 Antenna Reference No.: BDMW-WTW-P20121069-2 Page 11/26 2G1 Antenna Reference No.: BDMW-WTW-P20121069-2 Page 12/26 5G0+5G1 Antenna Reference No.: BDMW-WTW-P20121069-2 Page 13/26 Reference No.: BDMW-WTW-P20121069-2 Page 14/26 Model: SP230 Reference No.: BDMW-WTW-P20121069-2 Page 15/26 Reference No.: BDMW-WTW-P20121069-2 Page 16/26 Reference No.: BDMW-WTW-P20121069-2 Page 17/26 Reference No.: BDMW-WTW-P20121069-2 Page 18/26 Reference No.: BDMW-WTW-P20121069-2 Page 19/26 Reference No.: BDMW-WTW-P20121069-2 Page 20/26 Reference No.: BDMW-WTW-P20121069-2 Page 21/26 Reference No.: BDMW-WTW-P20121069-2 Page 22/26 Reference No.: BDMW-WTW-P20121069-2 Page 23/26 2G0 Antenna Reference No.: BDMW-WTW-P20121069-2 Page 24/26 2G1 Antenna Reference No.: BDMW-WTW-P20121069-2 Page 25/26 5G0 Antenna Reference No.: BDMW-WTW-P20121069-2 Page 26/26 5G1 Antenna

Report No.: SABDMW-WTW-P20121069 Page No. 1 / 7 Report Format Version: 6.1.1 RF Exposure Report Report No.: SABDMW-WTW-P20121069 FCC ID: M4Y-SP230 Test Model: SP230-S5 Series Model: SP230 Received Date: Dec. 31, 2020 Test Date: Feb. 04, 2021 Issued Date: Feb. 19, 2021 Applicant: Z-Com, Inc. Address: 5F, No.8, HSIN ANN RD., HSINCHU SCIENCE PARK, HSINCHU, 30078 TAIWAN Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SABDMW-WTW-P20121069 Page No. 2 / 7 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 2.4 Antenna Gain ...................................................................................................................................... 6 2.5 Calculation Result ............................................................................................................................... 7 Report No.: SABDMW-WTW-P20121069 Page No. 3 / 7 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SABDMW-WTW-P20121069 Original release. Feb. 19, 2021 Report No.: SABDMW-WTW-P20121069 Page No. 4 / 7 Report Format Version: 6.1.1 1 Certificate of Conformity Product: 802.11 ac Wave 2 Access Point Brand: ZCOM Test Model: SP230-S5 Series Model: SP230 Sample Status: Mass product Applicant: Z-Com, Inc. Test Date: Feb. 04, 2021 Standards: FCC Part 2 (Section 2.1091) IEEE C95.3 -2002 References Test Guidance: KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Feb. 19, 2021 Vivian Huang / Specialist Approved by : , Date: Feb. 19, 2021 Clark Lin / Technical Manager Report No.: SABDMW-WTW-P20121069 Page No. 5 / 7 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz ; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 26 cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SABDMW-WTW-P20121069 Page No. 6 / 7 Report Format Version: 6.1.1 2.4 Antenna Gain Model: SP230-S5 Antenna NO. Chain No. Brand Model Antenna Net Gain(dBi) Frequency range Antenna Type Connector Type Cable Length (mm) 2G0 Chain 0 (J26) BDTRON 1001A0018 5.5 2.4~2.4835GHz PCB i-pex(MHF) 230 2G1 Chain 1 (J24) BDTRON 1001A0018 5.5 2.4~2.4835GHz PCB i-pex(MHF) 230 5G0 Chain 0 (J23) BDTRON 98P1DUIPF000 9.52 10.39 10.39 10.14 5.15~5.25GHz 5.25~5.35GHz 5.47~5.725GHz 5.725~5.85GHz PCB i-pex(MHF) i-pex(MHF) 230 5G1 Chain 1 (J25) BDTRON 98P1DUIPF000 8.6 9.87 9.87 10.43 5.15~5.25GHz 5.25~5.35GHz 5.47~5.725GHz 5.725~5.85GHz PCB i-pex(MHF) 230 Model: S…

Text truncated - open the document above for the full version.

Report No.: RFBDMW-WTW-P20121069-1 Page No. 1 / 75 Report Format Version:6.1.2 FCC Test Report Report No.: RFBDMW-WTW-P20121069-1 FCC ID: M4Y-SP230 Test Model: SP230-S5 Series Model: SP230 Received Date: Dec. 31, 2020 Test Date: Jan. 18 to Feb. 05, 2021 Issued Date: Feb. 19, 2021 Applicant: Z-Com, Inc. Address: 5F, No.8, HSIN ANN RD., HSINCHU SCIENCE PARK, HSINCHU, 30078 TAIWAN Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwa. Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan. FCC Registration / Designation Number: 723255 / TW2022 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RFBDMW-WTW-P20121069-1 Page No. 2 / 75 Report Format Version:6.1.2 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................. 10 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................ 11 3.3 Duty Cycle of Test Signal .................................................................................................................. 13 3.4 Description of Support Units ............................................................................................................. 14 3.4.1 Configuration of System under Test .................................................................................................. 15 3.5 General Description of Applied Standard and references ................................................................. 17 4 Test Types and Results ...................................................................................................................... 18 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 18 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 18 4.1.2 Test Instruments ................................................................................................................................ 19 4.1.3 Test Procedure .................................................................................................................................. 21 4.1.4 Deviation from Test Standard ............................................................................................................ 22 4.1.5 Test Setup .......................................................................................................................................... 22 4.1.6 EUT Operating Condition .................................................................................................................. 23 4.1.7 Test Results ....................................................................................................................................... 24 4.2 Conducted Emission Measurement .................................................................................................. 44 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 44 4.2.2 Test Instruments ................................................................................................................................ 44 4.2.3 Test Procedure .................................................................................................................................. 45 4.2.4 Deviation from Test Standard ......................................................................................…

Text truncated - open the document above for the full version.

Reference No.: BDMW-WTW-P20121069 Page No. 1 / 4 Reference No.: PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Reference No.: BDMW-WTW-P20121069 Page No. 2 / 4 Reference No.: RADIATED EMISSION TEST (Below 1GHz) Reference No.: BDMW-WTW-P20121069 Page No. 3 / 4 Reference No.: RADIATED EMISSION TEST (Above 1GHz) Reference No.: BDMW-WTW-P20121069 Page No. 4 / 4 Reference No.: