M5VC30049XProx Readers T30

3Ennnn Gallagher T30 Reader Installation Note| DRAFT2 | July 2020 Copyright © Gallagher Group Limited Page 1 Gallagher T30 Keypad Reader Installation Note T30 MULTITECH® Keypad Reader, Black: C300490 T30 MULTITECH® Keypad Reader, White: C300491 T30 MIFARE® Keypad Reader, Black: C300495 T30 MIFARE® Keypad Reader, White: C300496 3Ennnn Gallagher T30 Reader Installation Note| DRAFT2 | July 2020 Copyright © Gallagher Group Limited Page 2 Disclaimer This document gives certain information about products and/or services provided by Gallagher Group Limited or its related companies (referred to as "Gallagher Group"). The information is indicative only and is subject to change without notice meaning it may be out of date at any given time. Although every commercially reasonable effort has been taken to ensure the quality and accuracy of the information, Gallagher Group makes no representation as to its accuracy or completeness and it should not be relied on as such. To the extent permitted by law, all express or implied, or other representations or warranties in relation to the information are expressly excluded. Neither Gallagher Group nor any of its directors, employees or other representatives shall be responsible for any loss that you may incur, either directly or indirectly, arising from any use or decisions based on the information provided. Except where stated otherwise, the information is subject to copyright owned by Gallagher Group and you may not sell it without permission. Gallagher Group is the owner of all trademarks reproduced in this information. All trademarks which are not the property of Gallagher Group, are acknowledged. Copyright © Gallagher Group Ltd 2020. All rights reserved. 3Ennnn Gallagher T30 Reader Installation Note| DRAFT2 | July 2020 Copyright © Gallagher Group Limited Page 3 Contents 1 Introduction ........................................................................................................................................ 4 2 Before you begin ................................................................................................................................. 4 2.1 Shipment contents................................................................................................................... 4 2.2 Power supply ........................................................................................................................... 4 2.3 Cabling ..................................................................................................................................... 4 3 Distance between readers .................................................................................................................. 6 4 Installation .......................................................................................................................................... 7 5 LED indications .................................................................................................................................. 10 6 Accessories ........................................................................................................................................ 10 7 Technical specifications .................................................................................................................... 11 8 Approvals and Compliance Standards .............................................................................................. 12 9 Mounting Dimensions ....................................................................................................................... 13 3Ennnn Gallagher T30 Reader Installation Note| DRAFT2 | July 2020 Copyright © Gallagher Group Limited Page 4 1 Introduction The Gallagher T30 Keypad Reader is available in a variety of variants. The variant you have purchased determines the available functionality and supported technologies for the reader. The Multi Tech variants C300490 and C300491 support Gallagher mobile credentials, using Bluetooth® low energy technology. The reader can be mounted on a rectangular 50 mm x 75 mm (2 in x 3 in) flush box, a BS 4662 British Standard square flush box, or any solid flat surface The terminal sends information to the Gallagher Controller and acts upon information sent from the Gallagher Controller. The terminal itself does not make any access decisions. 2 Before you begin 2.1 Shipment contents Check the shipment contains the following items: • 1 x Gallagher T30 Keypad Reader facia assembly • 1 x Gallagher T30 Keypad Reader bezel • 2 x 6-32 UNC (32 mm) Phillips drive fixing screws • 2 x M3.5 (40 mm) Phillips drive fixing screws • 5 x 25 mm No.6 self tapping, pan head, Phillips drive fixing screws • 1 x M3 Torx Post (T10) Security screw 2.2 Power supply The Gallagher T30 Keypad Reader is designed to operate over a supply voltage range of 9 - 16 Vdc measured at the readers. The operating current draw is dependent on the supply voltage at the reader. The power source should be linear or a good quality switched-mode power supply. The performance of the reader may be affected by a low quality, noisy power supply. 2.3 Cabling The Gallagher T30 Keypad Reader requires a minimum cable size of 4 core 24 AWG (0.2 mm 2 ) stranded security cable. This cable allows the transmission of data (2 wires) and power (2 wires). When using a single cable to carry both power supply and data, both the power supply voltage drop and data requirements must be considered. Although the reader is specified to operate at 9 Vdc, for good engineering design it is recommended that the voltage at the reader should be approximately 12 Vdc. HBUS cabling topology The HBUS communications protocol is based on the RS485 standard and allows the reader to communicate over a distance of up to 500 m (1640 ft). The cabling between HBUS devices should be done in a "daisy chain" topology, (i.e. A "T" or "Star" topology should not be used between devices). Should "Star" or "Home-Run" 3Ennnn Gallagher T30 Re…

Text truncated - open the document above for the full version.

Gallagher Group Ltd 181 Kahikatea Drive Private Bag 3026 Hamilton, New Zealand Tel: +64-7-838-9800 Fax: +64-7-838-9801 Email: [email protected] www.gallaghergroup.co.nz Companies Gallagher Group Ltd – NZ Sunplas Engineering (82) Ltd – NZ Gallagher Security (int) Ltd – NZ Gallagher Power Fence (SA) Pty – Sth Africa Gallagher Security (UK) Ltd – UK Gallagher Security (USA) Inc – USA Franklin Machinery – New Zealand PEC Pumps PEC Fuel Pumps Ltd Cardax (International) Ltd Gallagher Finance & Management Ltd Gallagher IT Solutions Ltd Reach Global Ltd Associate Companies Gallagher Europe Veldman & Djikstra Gallagher Australia Pty Ltd – Australia Gallagher Insultimber – Australia Gallagher Power Fence Inc – USA Gallagher Power Fencing Systems Inc – Canada Gallagher Power Fence (IRL) Ltd – Ireland Ibex Gallagher – India A/S Poda Hegn – Denmark NZ Producciones S.A – Argentina International Scales Pty Ltd - Australia August 12, 2010 To Whom It May Concern: I hereby appoint Menardo Lazaro to sign letters and applications for any filings with regulatory agencies on our behalf, and to receive and exchange data between our company, the agents company and the agency in connection with certification for any products that our company owns or manufactures. Sincerely, Tony Smith Technical Development Manager Gallagher Group Ltd.

GALLAGHER GROUP LIMITED 181 Kahikatea Drive, Hamilton 3206, New Zealand. Private Bag 3026, Hamilton 3240, New Zealand. TEL +64 7 838 9800 FAX +64 7 838 9801 EMAIL [email protected] WEB www.gallagher.com Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 August 5, 2020 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, Gallagher Group Ltd requests confidentiality for the following products: FCC ID Number Product Title/Model M5VC30049X T30 Multi Tech and T30 Mifare Readers For the products stated above, we request that the following information be held confidential: 1) Electrical Schematics of the Circuitry 2) Block Diagram 3) Operational Description 4) Internal Photos The T30 Multi Tech and Mifare Readers are potted. The potting is used for environmental protection to IP68 and security of the circuit design. This product is used in very high security applications to protect, for example, national infrastructure in many countries, where it is necessary such information is kept as confidential as possible. Removal of the potting material would damage or destroy the product. No other items submitted as part of the equipment authorization filing process are deemed confidential. The above exhibits contain Gallagher Group Ltd trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our Readers. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Menardo Lazaro Senior Compliance Engineer

Declaration of Completion of Integration Validation Performed for the Bluetooth Module ATTESTATION: I attest that the confirmation of integration validation performed on the Bluetooth module (FCC ID: QOQBGM111, IC: 5123A-BGM111) and T30 Reader (FCC ID: M5VC30049X, IC: 7369A-C30049X) was completed in accordance with KDB 996369 D04 Clause 3.1b. The validation was performed with the Bluetooth module and Mifare transceiver in the T30 Reader in simultaneous transmission. No emissions exceeded the highest limit permitted as required by Section 2.947(f). No anomalies were detected during repeated scans. The presence of the T30 Reader has no detrimental effect on the Bluetooth emissions. Signature: _______________________ Date: __11/08/2020_______ Name: ____Murray Long____________ Title: ____R&D Technical Leader_____ Company: _Gallagher Group Ltd.______ Product Model Numbers and Names: __C300490 – T30 Multi Tech Keypad Reader Black_______ __C300491 – T30 Multi Tech Keypad Reader White______ __C300495 – T30 Mifare Keypad Reader Black__________ __C300496 – T30 Mifare Keypad Reader White__________ T30 Reader FCC ID: ________M5VC30049X__________ T30 Reader IC: ____________7369A-C30049X________ Bluetooth Module FCC ID: __QOQBGM111___________ Bluetooth Module IC: ______5123A-BGM111_________

GALLAGHER GROUP LIMITED 181 Kahikatea Drive, Hamilton 3206, New Zealand. Private Bag 3026, Hamilton 3240, New Zealand. TEL +64 7 838 9800 FAX +64 7 838 9801 EMAIL [email protected] WEB www.gallagher.com 7/29/2020 Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 RE: Cover Letter To whom it may concern: The FCC test report number 200301.1 for T30 Reader – Multi Tech (Model No.: C300490) also covers the other models of T30 Multi Tech Reader (Model No.: C300491) and T30 Mifare Readers (Model Nos.: C300495 and C300496). All these model numbers are to be certified under FCC ID: M5VC30049X. # Product Characteristics: Products are: Same Different 1 Radio Frequency Operating Range(s) X 2 RF Power / Field Strength X 3 Radio Frequency Circuitry X 4 Antenna Characteristics X 5 Associated Digital Circuitry X 6 Functional Capabilities X 7 Cosmetic Differences X For any differences, a description is provided in the table below. # Description of differences: 5 The associated digital circuitry of models C300490 and C300491 have additional FCC and IC certified Bluetooth Low Energy (BLE) module in the Multi Tech variants for wireless communications with another Bluetooth capable device. The Mifare variants C300495 and C300496 do not have this circuit. 7 The models C300490 and C300495 have black enclosures, while C300491 and C300496 have white enclosures. Brief statement as to why the products should qualify for family approval: The products all share the same hardware. The radio parameters are identical among all family members. Sincerely, Menardo Lazaro Senior Compliance Engineer Gallagher Group Ltd

T30 Multi Tech & Mifare Readers – Product Labels 15 mm 48 mm Material: Thermafilm 21940 UL approved gloss white self-adhesive polyester Product is sold with mounting bracket which is required to be removed exposing label prior to install. This meets CFR 47 2.925(d)(2).

Alberga Business Park, Bertel Jungin aukio 3 FI-02600 Espoo, Finland Phone: +358 9 435 5060 www.silabs.com RF EXPOSURE ANALYSIS Product FCC ID BGM111 Bluetooth Module QOQBGM111 Analysis for FCC, portable use Standalone SAR test exclusion considerations are defined in the KDB 447498 Chapter 4.3.1. 1-g head or body SAR exclusion threshold is defined with formula [(max . power of channel, including tun-up tolerance, mW)/(min. separation distance, mm.)]* (√f(GHz))≤3 For BGM111 the maximum TX power is 8.0 mW and maximum TX frequency is 2.48 GHz. Using separation distance of 5 mm with the formula above results 351.248.2 5 8        mm mW According to KDB 447498, if the separation distance is less than 5mm, then 5mm separation distance is used to calculate the RF exposure. Thus BGM111 meets the SAR exclusion criteria with 0 mm separation and SAR evaluation is not needed. Analysis for FCC, mobile use 2 22 /00159.0 )20(4 8 4 ... cmmW cm mW R PRIE S    E.I.R.P (mW) Evaluation distance R (cm) Power density S at prediction frequency (mW/cm 2 ) MPE limit for uncontrolled exposure at prediction frequency (mW/cm 2 ) Verdict 13 20 0.00135 1 PASS

____________________________________________________________________________________________________________________________________________________________________________ Page 1 of 29 Test Report No 200301.1C 10 th August 2020 This report may not be reproduced except in full. EMC Technologies (NZ) Ltd 47 Mackelvie St, Grey Lynn Auckland 1021 New Zealand Phone 09 360 0862 Fax 09 360 0861 E-Mail Address: [email protected] Web Site: www.emctech.co.nz TEST REPORT Gallagher T30 Reader tested to the specification 47 Code of Federal Regulations Part 15 - Radio Frequency Devices Subpart C – Intentional Radiators Section 15.225 Operation within the band 13.110 -14.010 MHz for Gallagher Group Ltd This test report is issued with the authority of: ______________________________ Andrew Cutler - General Manager ____________________________________________________________________________________________________________________________________________________________________________ Page 2 of 29 Test Report No 200301.1C 10 th August 2020 This report may not be reproduced except in full. Table of Contents 1. STATEMENT OF COMPLIANCE 3 2. RESULTS SUMMARY 3 3. INTRODUCTION 4 4. CLIENT INFORMATION 4 5. DESCRIPTION OF TEST SAMPLE 5 6. SETUPS AND PROCEDURES 7 7. TEST EQUIPMENT USED 21 8. ACCREDITATIONS 21 9. PHOTOGRAPHS 22 ____________________________________________________________________________________________________________________________________________________________________________ Page 3 of 29 Test Report No 200301.1C 10 th August 2020 This report may not be reproduced except in full. 1. STATEMENT OF COMPLIANCE The Gallagher T30 Reader complies with FCC Part 15 Subpart C Section 15.225 as an Intentional Radiator when the methods as described in ANSI C63.10 - 2013 are applied. 2. RESULTS SUMMARY The results from testing carried out in between the 27 th May and the 2 nd June 2020 are detailed in the following table: Clause Parameter Result 15.201 Equipment authorisation requirement Certification required. 15.203 Antenna requirement Complies. Antenna internal to the device. 15.204 External PA and antenna modifications Not applicable. No external devices. 15.205 Restricted bands of operation Complies. Device transmits on a nominal frequency of 13.560 MHz. 15.207 Conducted limits Complies. 15.209 Radiated emission limits - Emissions < 30 MHz Complies. 15.209 Radiated emission limits – Emissions > 30 MHz Complies. 15.225 Radiated emission limits - Fundamental Complies. 15.225 Frequency stability Complies. ____________________________________________________________________________________________________________________________________________________________________________ Page 4 of 29 Test Report No 200301.1C 10 th August 2020 This report may not be reproduced except in full. 3. INTRODUCTION This report describes the tests and measurements performed for the purpose of determining compliance with the specification. The client selected the test sample. This report relates only to the sample tested. This report contains no erasures. This report contains following corrections and overrides the previous report no 200301_1B issued on 7 th August 2020. 1. Revised test sample identification details added. Measurement uncertainties with statistical confidence intervals of 95% are shown below test results. Both Class A and Class B uncertainties have been accounted for, as well as influence uncertainties where appropriate. All compliance statements have been made with respect of the specification limit with no reference to the measurement uncertainty. All testing was carried out as per the standard in the worst-case configuration with no deviations being applied. 4. CLIENT INFORMATION Company Name Gallagher Group Ltd Address 181 Kahikatea Drive Melville City Hamilton 3206 Country New Zealand Contact Mr Menardo Lazaro ____________________________________________________________________________________________________________________________________________________________________________ Page 5 of 29 Test Report No 200301.1C 10 th August 2020 This report may not be reproduced except in full. 5. DESCRIPTION OF TEST SAMPLE Brand Name Gallagher Model Number T30 The model number of sample tested is C300490 (T30 Multi Tech Keypad Reader Black). Product Reader Manufacturer Gallagher Group Ltd Country of Origin New Zealand Serial Number 123456789 FCC ID M5VC30049X Software version v1.00.24. The device tested is a RFID card reader that operates on 13.560 MHz that would typically be used to allow security access to buldings and locations. The product under test was powered at 12Vdc that was supplied from Gallagher 6000 HS controller. The controller inturn was powered from a 120 Vac to 12 Vdc convertor pictured in figure-3. The connections to the product from ancillaries have been represented in figure-1, 2 & 3. The laptop computer shown in the conducted emissions tests set up played no role in the carryout of the emissions testing but was supplied for completeness in this test. The laptop computer was was not required for the radiated emissions testing and hence this test was carried out without it being attached to the ancillary equipment. Figure-1: showing the tested product and ancillaries Product under test (DUT) Gallagher 6000 controller outputs 12 Vdc to DUT Laptop connected to Gallagher controller for DUT control via client software Associated cabling to connect DUT to Gallagher 6000 controller ____________________________________________________________________________________________________________________________________________________________________________ Page 6 of 29 Test Report No 200301.1C 10 th August 2020 This report may not be reproduced except in full. Figure-2: Gallagher supplied controller (Ancillary) Gallagher controller 6000 (HS) has been supplied by the client to assist in the testing of DUT. RS485 port connects this controller to the DUT The controller gets powered at 12Vdc using client …

Text truncated - open the document above for the full version.

____________________________________________________________________________________________________________________________________________________________________________ Page 1 of 10 Doc 200301.4 31 st July 2020 EMC Technologies (NZ) Ltd 47 Mackelvie St, Grey Lynn Auckland 1021 New Zealand Phone 09 360 0862 Fax 09 360 0861 E-Mail Address: [email protected] Web Site: www.emctech.co.nz Gallagher T30 Reader Test Setup Photos Radiated emissions test set up ____________________________________________________________________________________________________________________________________________________________________________ Page 2 of 10 Doc 200301.4 31 st July 2020 Radiated emissions test set up cont. ____________________________________________________________________________________________________________________________________________________________________________ Page 3 of 10 Doc 200301.4 31 st July 2020 Radiated emissions test set up cont. ____________________________________________________________________________________________________________________________________________________________________________ Page 4 of 10 Doc 200301.4 31 st July 2020 Radiated emissions test set up cont. ____________________________________________________________________________________________________________________________________________________________________________ Page 5 of 10 Doc 200301.4 31 st July 2020 Radiated emissions test set up cont. ____________________________________________________________________________________________________________________________________________________________________________ Page 6 of 10 Doc 200301.4 31 st July 2020 Radiated Emissions – Ancillary Test Equipment ____________________________________________________________________________________________________________________________________________________________________________ Page 7 of 10 Doc 200301.4 31 st July 2020 Conducted emissions test set up ____________________________________________________________________________________________________________________________________________________________________________ Page 8 of 10 Doc 200301.4 31 st July 2020 Test Shed showing the use of a Biconical Antenna ____________________________________________________________________________________________________________________________________________________________________________ Page 9 of 10 Doc 200301.4 31 st July 2020 Test shed showing the use of a log periodic antenna ____________________________________________________________________________________________________________________________________________________________________________ Page 10 of 10 Doc 200301.4 31 st July 2020 Test shed showing a loop antenna in use.