MMFSMP-WLWireless LAN Board

MB200i INSTALLATION MANUAL(WLAN BOARD) July 22, 2011 １ REMOVE CAP AND REMOVE SCREW. CAP SCREW SCREW CAP SCREW ２ REMOVE SCREW AND REMOVE TOP COVER AND FRONT COVER. TOP COVER FRONT COVER ３ REMOVE SCREW AND REMOVE SIDE COVER. SCREW SCREW ※PULL OUT SCREW ABOUT 1cm. SIDE COVER ※ PULL OUT SCREW ABOUT 1cm. ROTATE SIDE COVER AS SHOWN FIGURE ABOVE UNTIL INSIDE CAN BE SEEN. ４ SET WLAN BOARD AND TIGHTEN THE SCREW. FINALLY CONNECT FFC CABLE TO CONNECTOR AND LOCK THE CONNECTOR. SCREW FFC CABLE ５ FOLLOW PROCEDURE 3→2→1 IN ORDER TO INSTALL BACK THE PRINTER. ※(CASE PARTS ARE EASY TO COME OFF). ※BEWARE AND MAKE SURE THE CABLE DO NOT STUCK WHEN PUTTING BACK SIDE COVER. SPRING GEAR End Product Labeling The final end product must be labeled in a visible area with the following "Contains FCC ID：MMFSMP-WL".

                              !

                 

Top With shield Top Without shield Bottom

Antenna Photo Antenna Antenna

1. EMI Label location Affix the EMI label on the Wireless LAN Board same direction with ZP Affix the label not to run off the edge.

1 F E D 23 C B A 1 234 CHANGE OF CONTENTSREVIS FIRST EDITION DATEDESIGN 㬍 㬍 㬍 㬍 㬍 1/1 SHEET MATERIAL APPROVEDCHECKED DWG No. TITLE FINISH SCALE1:1 F E D C B A A4 SIZE Confidential © silex technology, Inc. 㪫㪅㪤㫀㫅㫆㪹㪼 㪜㪤㪠㩷㪣㪸㪹㪼㫃 㪟㪧㪈㪈㪎㪊㪇㪯㪯 㪧㫉㫀㫅㫋㫀㫅㪾㩷㪚㫆㫃㫆㫉㩷㪑㩷㪙㫃㪸㪺㫂 㪡㫌㫃㪅㪈㪈㪃㪈㪈 㪧㪜㪫㩷㪝㫀㫃㫄㩷㪌㪇㱘㫄 㪮㪿㫀㫋㪼 䊋䊷䉮䊷䊄㩷 䋺ᜰቯ䈘䉏䈢㪜㪿㫋㪼㫉㫅㪼㫋㩷㪘㪻㪻㫉㪼㫊㫊䉕㪨㪩㩷㪚㫆㪻㪼㩿䊝䊂䊦㪉㪀ൻ䈚䈩ශ೚䈜䉎੐䇯 㪫㪅㪢㫀㫄㫆㫋㫆㪢㪅㪦㫂㪸㫑㪸㫂㫀 17 㫧 0.2 4-R1  :::::: R 99%7. )<%7. /QFGN5/29. (%%+&//(5/29. /CFG KP,CRCP 17 㫧0.2 2.4 DS/OF 4

Top With shield Top Without shield Bottom

Test report No. : 31AE0084-HO-02-B-R1 Page : 2 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 SECTION 1: Customer information ................................................................................................................................................................... 3 SECTION 2: Equipment under test (E.U.T.) ..................................................................................................................................................... 3 2.1 Identification of E.U.T. ....................................................................................................................................... 3 2.2 Product Description ............................................................................................................................................ 3 SECTION 3 : Test standard information ........................................................................................................................................................... 4 3.1 Requirements for compliance testing defined by the FCC ................................................................................. 4 3.2 Procedure and result ........................................................................................................................................... 5 3.3 Exposure limit .................................................................................................................................................... 6 3.4 Test Location ...................................................................................................................................................... 6 SECTION 4 : Description of the operating mode .............................................................................................................................................. 7 4.1 Operating modes ................................................................................................................................................. 7 4.2 SAR testing operating modes ............................................................................................................................. 8 4.3 Confirmation before SAR testing ....................................................................................................................... 10 4.4 Confirmation after SAR testing .......................................................................................................................... 10 SECTION 5 : Description of the Body setup ...................................................................................................................................................... 11 5.1 Test position ....................................................................................................................................................... 11 SECTION 6 : Test surrounding ........................................................................................................................................................................... 12 6.1 Measurement uncertainty ................................................................................................................................... 12 SECTION 7 : Measurement results ..................................................................................................................................................................... 13 7.1 WLAN SAR ....................................................................................................................................................... 13 APPENDIX 1 : Photographs of test setup ............................................................................................................................ 16 1. Photographs of EUT ............................................................................................................................................ 17 2. Photographs of Host device ................................................................................................................................ 18 3. Photograph of Setup (MB201i) ........................................................................................................................... 22 4. Photograph of Setup (MB400i) ........................................................................................................................... 29 APPENDIX 2 : SAR Measurement data .............................................................................................................................. 36 1. Evaluation procedure .......................................................................................................................................... 37 2. Host device (MB201i) SAR DATA .................................................................................................................... 38 3. Host device (MB400i) SAR DATA .................................................................................................................... 54 APPENDIX 3 : Test instruments .......................................................................................................................................... 63 1. Equipment used ................................................................................................................................................... 64 2. Dosimetry assessment setup ................................................................................................................................ 65 3. Configuration and peripherals ............................................................................................................................. 66 4. System components ...............................................................................…

Text truncated - open the document above for the full version.

Test report No. : 31AE0084-HO-02-B-R1 Page : 16 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 APPENDIX 1 : Photographs of test setup Test report No. : 31AE0084-HO-02-B-R1 Page : 17 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 1. Photographs of EUT <EUT Information> EUT(Module and antenna 2) Extended antenna 1 SATO CORPORATION designates silex technology, Inc. as manufacturer of the product (Wireless LAN Board). <Host device Information> *Difference point: MB200series= Shape size , MB400series=Dots size MB200iMB201iMB400iMB410i W88mm x L73mm x H128mm W88mm x L64mm x H119mm 8 dots/mm (203 dpi)12 dots/mm (305 dpi) 99999999 Model name MB200 seriesMB400 series Antenna 1 & Antenna 2 W170mm×L76mm×H134mm Li-ion battery 7.4V /2400mAh Li-ion battery 14.8V/1700mAhBattery Antenna shape size(mm) (WxLxH) Dots size8 dots/mm (203 dpi) Antenna 2 Serial No.9M200588 Shortest distance from user(mm) ManufacturerSATO CORPORATIONSATO CORPORATION 14mm4.2mm Tested No Yes Yes No : Module : Antenna 2 : Antenna 1 : Port for Antenna 1 Test report No. : 31AE0084-HO-02-B-R1 Page : 18 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 2. Photographs of Host device <MB201i> Top Front Rear Right side Left side Bottom Antenna 1 Antenna 2 Controlled cable for test Test report No. : 31AE0084-HO-02-B-R1 Page : 19 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 Antenna location Right side : Antenna 1 Leftt side :EUT & Antenna 2 Antenna Antenna Antenna Antenna Antenna Test report No. : 31AE0084-HO-02-B-R1 Page : 20 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 <MB400i> Top Front Rear Bottom Right side Left side Antenna 2 Test report No. : 31AE0084-HO-02-B-R1 Page : 21 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 Antenna location Right side : EUT & Antenna 2 Antenna Antenna

Test report No. : 31AE0084-HO-02-B-R1 Page : 22 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 3. Photograph of Setup (MB201i) (1) Front Test report No. : 31AE0084-HO-02-B-R1 Page : 23 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (2) Rear Test report No. : 31AE0084-HO-02-B-R1 Page : 24 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (3) Right side Test report No. : 31AE0084-HO-02-B-R1 Page : 25 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (4) Left side Test report No. : 31AE0084-HO-02-B-R1 Page : 26 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (5) Top Test report No. : 31AE0084-HO-02-B-R1 Page : 27 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (6) Bottom Test report No. : 31AE0084-HO-02-B-R1 Page : 28 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (7) Right side 5mm Test report No. : 31AE0084-HO-02-B-R1 Page : 29 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 4. Photograph of Setup (MB400i) (1) Front Test report No. : 31AE0084-HO-02-B-R1 Page : 30 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (2) Rear Test report No. : 31AE0084-HO-02-B-R1 Page : 31 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (3) Right side Test report No. : 31AE0084-HO-02-B-R1 Page : 32 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (4) Left side Test report No. : 31AE0084-HO-02-B-R1 Page : 33 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (5) Top Test report No. : 31AE0084-HO-02-B-R1 Page : 34 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (6) Bottom Test report No. : 31AE0084-HO-02-B-R1 Page : 35 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 (7) Right side 5mm

Test report No. : 31AE0084-HO-02-B-R1 Page : 36 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 APPENDIX 2 : SAR Measurement data Test report No. : 31AE0084-HO-02-B-R1 Page : 37 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 1. Evaluation procedure The evaluation was performed with the following procedure: Step 1: Measurement of the E-field at a fixed location above the ear point or central position of flat phantom was used as a reference value for assessing the power drop. Step 2: The SAR distribution at the exposed side of head or body position was measured at a distance of each device from the inner surface of the shell. The area covered the entire dimension of the antenna of EUT and the horizontal grid spacing was 15 mm x 15 mm . Based on these data, the area of the maximum absorption was determined by spline interpolation. Step 3: Around this point found in the Step 2 (area scan) , a volume of 30mm x 30mm x 30mm was assessed by measuring 7 x 7 x 7 points. And for any secondary peaks found in the Step2 which are within 2dB of maximum peak and not with this Step3 (Zoom scan) is repeated. On the basis of this data set, the spatial peak SAR value was evaluated under the following procedure: (1). The data at the surface were extrapolated, since the center of the dipoles is 1mm(EX3DV3) away from the tip of the probe and the distance between the surface and the lowest measuring point is 1.3 mm. The extrapolation was based on a least square algorithm [4]. A polynomial of the fourth order was calculated through the points in z-axes. This polynomial was then used to evaluate the points between the surface and the probe tip. (2). The maximum interpolated value was searched with a straightforward algorithm. Around this maximum the SAR values averaged over the spatial volumes (1 g or 10 g) were computed by the 3D-Spline interpolation algorithm. The 3D- Spline is composed of three one-dimensional splines with the “Not a knot"-condition (in x, y and z-directions) [4], [5]. The volume was integrated with the trapezoidal-algorithm. One thousand points (10 x 10 x 10) were interpolated to calculate the average. (3). All neighboring volumes were evaluated until no neighboring volume with a higher average value was found. Step 4: Re-measurement of the E-field at the same location as in Step 1. Test report No. : 31AE0084-HO-02-B-R1 Page : 38 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 2. Host device (MB201i) SAR DATA SMP-WL (MB201i) WLAN 11b Ant.port1 2437MHz Front Communication System: WLAN 11a/b/g/n ; Communication System Band: WLAN 11b/g/n; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 2.02 mho/m; ε r = 50.4; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2007) DASY5 Configuration: Probe: EX3DV3 - SN3507; ConvF(7.61, 7.61, 7.61); Calibrated: 2011/03/16 Sensor-Surface: 2mm (Mechanical Surface Detection) Electronics: DAE3 Sn509; Calibrated: 2010/07/07 Phantom: ELI 4.0; Type: QDOVA001BA; Serial: xxxx Measurement SW: DASY52, Version 52.6 (1); Area Scan (81x81x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (interpolated) = 0.016 mW/g Zoom Scan (7x7x7) 2 (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.364 V/m; Power Drift = -0.19 dB Peak SAR (extrapolated) = 0.023 W/kg SAR(1 g) = 0.011 mW/g; SAR(10 g) = 0.00636 mW/g Maximum value of SAR (measured) = 0.017 mW/g Date: 2011/06/09 Ambient Temp. : 24.5 degree.C. Liquid Temp.; 23.5 degree.C. Test report No. : 31AE0084-HO-02-B-R1 Page : 39 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 SMP-WL (MB201i) WLAN 11b Ant.port1 2437MHz Rear Communication System: WLAN 11a/b/g/n ; Communication System Band: WLAN 11b/g/n; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 2.02 mho/m; ε r = 50.4; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2007) DASY5 Configuration: Probe: EX3DV3 - SN3507; ConvF(7.61, 7.61, 7.61); Calibrated: 2011/03/16 Sensor-Surface: 2mm (Mechanical Surface Detection) Electronics: DAE3 Sn509; Calibrated: 2010/07/07 Phantom: ELI 4.0; Type: QDOVA001BA; Serial: xxxx Measurement SW: DASY52, Version 52.6 (1); Area Scan (81x81x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (interpolated) = 0.048 mW/g Zoom Scan (7x7x7) 2 (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 3.858 V/m; Power Drift = 0.0086 dB Peak SAR (extrapolated) = 0.069 W/kg SAR(1 g) = 0.036 mW/g; SAR(10 g) = 0.019 mW/g Maximum value of SAR (measured) = 0.051 mW/g Date: 2011/06/09 Ambient Temp. : 24.5 degree.C. Liquid Temp.; 23.5 degree.C. Test report No. : 31AE0084-HO-02-B-R1 Page : 40 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 SMP-WL (MB201i) WLAN 11b Ant.port1 2437MHz Right side Communication System: WLAN 11a/b/g/n ; Communication System Band: WLAN 11b/g/n; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 2.02 mho/m; ε r = 50.4; ρ = 1000 kg/m 3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2007) DASY5 Configuration: Probe: EX3DV3…

Text truncated - open the document above for the full version.

Test report No. : 31AE0084-HO-02-B-R1 Page : 63 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 APPENDIX 3 : Test instruments Test report No. : 31AE0084-HO-02-B-R1 Page : 64 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 1. Equipment used Control No. Instrument Manufacturer Model No Serial No Test Item Calibration Date * Interval(month) MAT-20 Attenuator(10dB)(above 1GHz) HIROSE ELECTRIC CO.,LTD. AT-110 - Power measurement SAR 2011/01/06*12 MPM-08 Power Meter Anritsu ML2495A 6K00003338 Power measurement SAR 2010/09/10 * 12 MPSE-11 Power sensor Anritsu MA2411B 011737 Power measurement SAR 2010/09/10 * 12 MPM-01 Power Meter Agilent E4417A GB41290639 SAR 2011/02/01 * 12 MPSE-01 Power Sensor Agilent E9300B US40010300 SAR 2011/01/28 * 12 MPSE-03 Power sensor Agilent E9327A US40440576 SAR 2011/02/02 * 12 MAT-15 Attenuator(30dB) Agilent 8498A US40010300 SAR 2011/02/16 * 12 MSG-10 Signal Generator Agilent N5181A MY47421098 SAR 2010/09/08 * 12 MPA-12 MicroWave System Amplifier Agilent 83017A MY39500780 SAR 2011/03/10 * 12 MHDC-11 Dual Directional Coupler Hewlett Packard 778D 16605 SAR Pre Check MNA-01 Network Analyzer Agilent/HP E8358A US41080381 SAR 2010/08/19 * 12 MDPK-01 Dielectric probe kit Agilent 85070D 702 SAR 2010/10/25 * 12 MNCK-01 Type N Calibration Kit Agilent 85032F MY41495257 SAR 2010/08/10 * 12 MPB-03 Dosimetric E-Field Probe Schmid&Partner Engineering AG EX3DV3 3507 SAR 2011/03/16 * 12 MDAE-01 Data Acquisition Electronics Schmid&Partner Engineering AG DAE3 V1 509 SAR 2010/07/07 * 12 MPF-02 2mmOval Flat Phantom ERI 4.0 Schmid&Partner Engineering AG QD VA 001B (ERI4.0) 1045 SAR Pre Check COTS-MSAR-02 DASY5 Schmid&Partner Engineering AG DASY52 V52.6 - SAR - COTS-MSAR-02 S-Parameter Network Analyzer Agilent - - SAR - MDA-07 Dipole Antenna Schmid&Partner Engineering AG D2450V2 713 SAR 2010/09/06 * 36 MOS-26 Thermo-Hygrometer Custom CTH-201 A08Q29 SAR 2011/05/26 * 12 MOS-10 Digtal thermometer HANNA Checktemp-2 MOS-10 SAR 2010/08/02 * 12 MBM-13 Barometer Sunoh SBR121 837 SAR 2011/03/14 * 36 Body2450 Daily check Target value ± 5% SAR room Daily check Ambient Noise<0.012W/kg The expiration date of the calibration is the end of the expired month. As for some calibrations performed after the tested dates, those test equipment have been controlled by means of an unbroken chains of calibration As for some calibrations performed after the tested dates, those test equipment have been controlled by means of an unbroken chains of calibrations. Test report No. : 31AE0084-HO-02-B-R1 Page : 65 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 2. Dosimetry assessment setup These measurements were performed with the automated near-field scanning system DASY4 from Schmid & Partner Engineering AG (SPEAG). The system is based on a high precision robot (working range greater than 0.9 m), which positions the probes with a positional repeatability of better than +/- 0.02 mm. Special E- and H-field probes have been developed for measurements close to material discontinuity, the sensors of which are directly loaded with a Schottky diode and connected via highly resistive lines to the data acquisition unit. The SAR measurements were conducted with the dosimetry probe EX3DV3, SN: 3507 (manufactured by SPEAG), designed in the classical triangular configuration and optimized for dosimetric evaluation. The probe has been calibrated according to the procedure described in [2] with accuracy of better than +/-10%. The spherical isotropy was evaluated with the procedure described in [3] and found to be better than +/-0.25 dB. The phantom used was the SAM Twin Phantom as described in FCC supplement C, IEEE P1528 and CENELEC EN50361. Test report No. : 31AE0084-HO-02-B-R1 Page : 66 of 96 FCC ID : MMFSMP-WL Issued date : July19, 2011 Revised date : July 28, 2011 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone: +81 596 24 8116 Facsimile: +81 596 24 8124 3. Configuration and peripherals The DASY5 system for performing compliance tests consist of the following items: 1. A standard high precision 6-axis robot (Stäubli RX family) with controller and software. An arm extension for accommodating the data acquisition electronics (DAE). 2. An isotropic field probe optimized and calibrated for the targeted measurement. 3. A data acquisition electronic (DAE), which performs the signal amplification, signal multiplexing, AD-conversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is battery powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC. 4. The Electro-optical converter (EOC) performs the conversion between optical and electrical of the signals for the digital communication to the DAE and for the analog signal from the optical surface detection. The EOC is connected to the measurement server. 5. The function of the measurement server is to perform the time critical tasks such as signal filtering, control of the robot operation and fast movement interrupts. 6. The Light Beam used is for probe alignment. This improves the (absolute) accuracy of the probe positioning. 7. A computer running WinXP and the DASY5 software. 8. Remote control with teaches pendant and additional circuitry for robot safety such as warning lamps, etc. 9. The phantom, the device holder and other accessories according to the targeted measurement. Test report No. : 31AE0084-HO-02-B-R1 Page : 67 of 96 FCC ID : MMFSMP…

Text truncated - open the document above for the full version.

Test report No. : 31AE0084-HO-02-A Page : 2 of 75 Issued date : July 26, 2011 FCC ID : MMFSMP-WL UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information ......................................................................................................... 3 SECTION 2: Equipment under test (E.U.T.) ........................................................................................... 3 SECTION 3: Test specification, procedures & results ............................................................................ 4 SECTION 4: Operation of E.U.T. during testing .................................................................................... 7 SECTION 5: Conducted Emission .......................................................................................................... 10 SECTION 6: Radiated Spurious Emission ............................................................................................ 11 SECTION 7: Antenna Terminal Conducted Tests ................................................................................ 12 APPENDIX 1: Photographs of test setup ............................................................................................... 13 Conducted Emission ......................................................................................................................... 13 Worst Case Position .......................................................................................................................... 16 APPENDIX 2: Data of EMI test .............................................................................................................. 17 Conducted Emission ......................................................................................................................... 17 6dB Bandwidth ................................................................................................................................. 21 Maximum Peak Output Power .......................................................................................................... 24 Radiated Spurious Emission ............................................................................................................. 26 Conducted Spurious Emission .......................................................................................................... 43 Conducted Emission Band Edge compliance ................................................................................... 67 Power Density ................................................................................................................................... 69 99%Occupied Bandwidth ................................................................................................................. 72 APPENDIX 3: Test instruments ............................................................................................................. 74 Test report No. : 31AE0084-HO-02-A Page : 3 of 75 Issued date : July 26, 2011 FCC ID : MMFSMP-WL UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 SECTION 1: Customer information Company Name : SATO CORPORATION Address : 1-207, Onari-cho, Omiya-ku, Saitama-shi, Saitama, 330-0852 Japan Telephone Number : +81-48-663-…

Text truncated - open the document above for the full version.