MQ4BSMMC1Bluetooth Audio Adapter

Bluetooth HeadsetBluetooth Transmitter Battery Cover-Release Button Line-out Jack to Stereo System Battery Compartment cover Power On/Off Switch Power On/Off Switch Power LED (Green) LED (Red / Blue) Audio Plug (to iPod headphone port) Volume Level Control P O W E R V O L U M E P O WER VO L UME ONOFF User's Guide Package Contents: Thank you for purchasing the bluetooth headset and transmitter that connects to iPod. The headset can serves as a wireless streaming device, all it takes is to connect the home stereo system to it’s line-out port. The iPod is used as a remote control and can stream music from as far as 30 feet to the headset or home stereo system. 1) Bluetooth Headset 2) Bluetooth Transmitter 3) 4 AAA batteries 4) Line-out audio cable Specifications: Power requirements DC 3V [1.5V AAA x 2] Headset Speaker 40mm Mylar cone Impedance 32 Ohms ± 4 Ohms Distortion 1% THD at NOM.DEV S/N Ratio 60dB R/L Balance ±2dB (mono) Weight Approx. 170g Hardware Basics LR Facts and Tips 1. Press the battery compartment Cover-Release button on the headset to open the cover and insert two 1.5volt, AAA batteries. 2. Open the battery compartment cover from the back of the transmitter and insert two 1.5volt, AAA batteries 3. Slide the Headset power switch on, the LED light will turn green. 4. Slide the Transmitter power switch on, the LED light will turn red and start pairing with the headset. Once the pairing is finished, LED light will turn to blue color and flash steadily. 5. Plug the transmitter to your iPod or any music player and enjoy cordless stereo music. When finished, make sure to turn off both transmitter and headset to conserve battery power. 1) Working distance is 30ft, actual distance will depending upon the battery power level, walls, doors, furnitures and position angle of the transmitter and headset. 2) Bluewave can be used with other audio device like MP3 player, CD player, TV and computer etc. Additional cable adapter maybe required. 3) Headset also support Bluetooth enabled PC computers. However, the quality of the stereo depends on the OS support. Please check our website for update information. 4) Rare static (noise) in the headset is normal. Occasional static may indicate low battery power level or transmitter/ headset are too far apart. Move headset closer to transmitter. If static situation does not improve, replace batteries on transmitter and headset. 5) Either alkaline or rechargeable AAA batteries can be used. Battery lasts 2 to 8 hours typically. 6) Music playback volume can be adjusted from iPod and/or headset. 6. To stream music to stereo system, please follow step 1 to 5, then put headset next to stereo system, connect the audio cable from line out jack on the headset to AUX/Video RCA jack (both left and right channel.) In stereo system select AUX/Video mode, now everyone can start enjoying music from iPod through your stereo system. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

Label location (645x368x16M jpeg)

Bluetooth Audio Adapter Model name : BSMMC1 FCC ID : MQ4BSMMC 1

Page 3 Page 4 Page 5

FCC ID: MQ4BSMMC1 Report No.: RF940315L08 Operational Description The transmitter of the EUT (Bluetooth Audio Adapter) is powered by battery. The antenna is PIFA antenna without antenna connector. For more detailed instruction, please take a look at the user’s manual. This device is a Frequency Hopping device with 79 hopping frequencies.

FCC ID: MQ4BSMMC1 Report No: SA940315L08 1 RF EXPOSURE REPORT REPORT NO.: SA940315L08 MODEL NO.: BSMMC1 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: AboCom Systems, Inc. ADDRESS: 1F, No. 21, Yanfa 2 nd Rd., SBIP, Hsinchu City 300, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. FCC ID: MQ4BSMMC1 Report No: SA940315L08 2 RF Exposure Measurement 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500......F/3006 1500-100,000......56 (B)Limits For General Population / Uncontrolled Exposure 300-1500......F/15006 1500-100,000......1.030 F = Frequency in MHz FCC ID: MQ4BSMMC1 Report No: SA940315L08 3 3. Friis Formula Friis transmission formula: Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance 20cm. Ref.: David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. FCC ID: MQ4BSMMC1 Report No: SA940315L08 4 5. Conclusion No Evaluation Required if power is below this threshold: F(GHz)mW Low2.402 High2.480 24.58 Maximum measured transmitter power: Pout (dBm)Pout (mW) Conducted Power2.921.959 EIRP Power5.893.882 *Note: The antenna is PIFA antenna with 2.97dBi gain Threshold for no SAR evaluation is 24.58mW Transmitter power is 3.882mW Conclusion: No SAR evaluation required since Transmitter Pout is below FCC threshold

FCC ID: MQ4BSMMC1 Report No.: RF940315L081Report Format Version 2.0.2 FCC TEST REPORT REPORT NO.: RF940315L08 MODEL NO.: BSMMC1 RECEIVED: Mar. 28, 2005 TESTED: Mar. 30, 2005 ISSUED: Apr. 01, 2005 APPLICANT: AboCom Systems, Inc. ADDRESS: 1F, No. 21, Yanfa 2 nd Rd., SBIP, Hsinchu City 300, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 61 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agency. The test results in the report only apply to the tested sample. 0528 ILAC MRA No. 2177-01 FCC ID: MQ4BSMMC1 Report No.: RF940315L082Report Format Version 2.0.2 TABLE OF CONTENTS 1CERTIFICATION ....................................................................................................... 4 2SUMMARY OF TEST RESULTS ............................................................................... 5 2.1MEASUREMENT UNCERTAINTY............................................................................. 5 3GENERAL INFORMATION........................................................................................ 6 3.1GENERAL DESCRIPTION OF EUT .......................................................................... 6 3.2DESCRIPTION OF TEST MODES ............................................................................ 7 3.2.1CONFIGURATION OF SYSTEM UNDER TEST .......................................................8 3.2.2TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................9 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ......................................... 10 3.4DESCRIPTION OF SUPPORT UNITS .................................................................... 10 4TEST PROCEDURES AND RESULTS ................................................................... 11 4.1CONDUCTED EMISSION MEASUREMENT .......................................................... 11 4.1.1LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................ 11 4.1.2TEST INSTRUMENTS............................................................................................. 11 4.1.3TEST PROCEDURES .............................................................................................12 4.1.4DEVIATION FROM TEST STANDARD ...................................................................12 4.1.5TEST SETUP...........................................................................................................13 4.1.6EUT OPERATING CONDITIONS ............................................................................13 4.1.7TEST RESULTS ......................................................................................................14 4.2NUMBER OF HOPPING FREQUENCY USED ....................................................... 20 4.2.1LIMIT OF HOPPING FREQUENCY USED .............................................................20 4.2.2TEST INSTRUMENTS.............................................................................................20 4.2.3TEST PROCEDURES .............................................................................................21 4.2.4DEVIATION FROM TEST STANDARD ...................................................................21 4.2.5TEST SETUP...........................................................................................................22 4.2.6TEST RESULTS ......................................................................................................22 4.3DWELL TIME ON EACH CHANNEL ....................................................................... 24 4.3.1LIMIT OF DWELL TIME USED................................................................................24 4.3.2TEST INSTRUMENTS.............................................................................................24 4.3.3TEST PROCEDURES .............................................................................................25 4.3.4DEVIATION FROM TEST STANDARD ...................................................................25 4.3.5TEST SETUP...........................................................................................................25 4.3.6TEST RESULTS ......................................................................................................26 4.4CHANNEL BANDWIDTH ......................................................................................... 30 4.4.1LIMITS OF CHANNEL BANDWIDTH ......................................................................30 4.4.2TEST INSTRUMENTS.............................................................................................30 4.4.3TEST PROCEDURE................................................................................................31 4.4.4DEVIATION FROM TEST STANDARD ...................................................................31 4.4.5TEST SETUP...........................................................................................................31 4.4.6EUT OPERATING CONDITION ..............................................................................31 4.4.7TEST RESULTS ......................................................................................................32 4.5HOPPING CHANNEL SEPARATION ...................................................................... 35 FCC ID: MQ4BSMMC1 Report No.: RF940315L083Report Format Version 2.0.2 4.5.1LIMIT OF HOPPING CHANNEL SEPARATION ......................................................35 4.5.2TEST INSTRUMENTS.............................................................................................35 4.5.3TEST PROCEDURES ..................…

Text truncated - open the document above for the full version.

FCC ID: MQ4BSMMC1 Report No.: RF940315L0859Report Format Version 2.0.2 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: MQ4BSMMC1 Report No.: RF940315L0860Report Format Version 2.0.2 RADIATED EMISSION TEST