MQ4WMG2501Wireless LAN MINI PCI Card

802.11g Wireless LAN MINI PCI Card User’s Manual REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B CAUTION: This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. LABELING REQUIREMENT FOR OEM INTEGRATOR: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users The final end product must be labeled in a visible area with the following: "Contains TX FCC ID: MQ4WMG2501". Note for Installation ( MQ4WMG2501 ) The attached antenna cable has to be connected on the port shown below for Tx/Rx. Port for Tx/Rx Table of Contents INTRODUCTION ...................................................................................................1 WIRELESS NETWORK OPTIONS...............................................................................1 The Peer-to-Peer Network .........................................................................1 The Access Point Network ........................................................................2 INSTALLATION ....................................................................................................3 INSTALL THE DEVICE..............................................................................................3 INSTALL THE DRIVER & UTILITY............................................................................3 Verify Device Installation..........................................................................5 CONFIGURATION ................................................................................................6 ACCESSING THE CONFIGURATION UTILITY..............................................................6 EASY CONFIG.........................................................................................................7 MAIN TAB............................................................................................................10 PROFILE MANAGER TAB.......................................................................................12 ADVANCED TAB...................................................................................................18 INFO TAB.............................................................................................................19 ABOUT TAB..........................................................................................................20 UNINSTALLATION.............................................................................................21 - 1 - INTRODUCTION The 802.11g Wireless LAN MINI PCI Card is a device that allows you connect your computer to a wireless local area network (LAN). A wireless LAN allows your system to use wireless Radio Frequency (RF) technology to transmit and receive data without physically attaching to the network. The Wireless protocols that come with this product ensure data security and isolation from interference generated by other radio frequencies. This card also allows you to take full advantage of your computer’s mobility with access to real-time information and online services anytime and anywhere. In addition, this device eliminates the bother of pulling cable through walls and under furniture. It even allows you to place your system in locations where cabling is impossible. Modifying and augmenting networks has never been so easy. Wireless Network Options The Peer-to-Peer Network This network installation lets you set a small wireless workgroup easily and quickly. Equipped with wireless PC Cards or wireless MINI PCI, you can share files and printers between each PC and laptop. - 2 - You can also use one computer as an Internet Server to connect to a wired global network and share files and information with other computers via a wireless LAN. The Access Point Network The network installation allows you to share files, printers, and Internet access much more conveniently. With Wireless LAN Cards, you can connect wireless LAN to a wired global network via an Access Point. - 3 - INSTALLATION Install the device 1. Make sure the computer is turned off. Remove the expansion slot cover from the computer. 2. Carefully slide the Wireless MINI PCI Card into the MINI PCI slot. Push evenly and slowly and ensure it is properly seated, you may have to use the mounting screw to have the card screwed securely in place. 3. After the device has been connected to your computer, turn on your computer. Windows wil…

Text truncated - open the document above for the full version.

Page No. : 6 Module Approval Request Letter Subject: Module Approval Date: 2005/12/1 FCC ID: MQ4WMG2501 Dear Reviewer, We, Sporton International Inc., are authorized by AboCom Systems, Inc to have their state-of-the-art Mini PCI approved under module approval authorization. The application of this module is specified to Mobile host equipment. The requirements regulated in Public Notice DA00-1407 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip RTL8185L . 3. The requirement of power supply regulation: The part number of the power regulator is AME8801MEEVZ SOT23-5. 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 8. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance of RF exposure rule. Please do not hesitate to contact me for any questions of this request letter. Thank you. Company name : Sporton International Inc. Company Address : No. 52, Hwa Ya 1st Road., Kwei-Shan Hsiang, TaoYuan Hsien Taiwan R.O.C. Signature : Name : Wayne Hsu Job Title : Supervisor

SPORTON International Inc. PAGE NUMBER : A1 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Dec,13,2005 FAX : 886-2-2696-2255 APPENDIX A. Photographs of EUT

FCC ID:MQ4WMG2501 This device complies with Part 15 of the FCC Rules.

SPORTON International Inc. PAGE NUMBER : A2 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Dec,13,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A3 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Dec,13,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A4 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Dec,13,2005 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A5 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Dec,13,2005 FAX : 886-2-2696-2255

Opreational Description Date: 2005/12/13 EUT is a Mini PCI card with 11 channels(2412MHz~2462MHz, Space 5MHz). It allows you to connect to other WLAN device. General Operational Description: 1. Time base of the transmission frequency: For IF and RF frequency, Crystal is a clock reference. 2. Synthesizer: Synthesizer inside Transceiver IC and operate frequency in 2.4GHz ISM Band. Internal voltage controlled oscillator (VCO) provides the desired LO signal base on the phase-locked loop (PLL) with a relatively wide tuning range for this application. 3. Transmission: BBP IC has DSSS (BPSK/QPSK/CCK) and OFDM (BPSK/QPSK/16QAM/64QAM) modulation function, it provides transmission data rate are 1, 2, 5.5, 11 Mbps on DSSS and 6, 12, 18, 24, 36, 48, 54 Mbps on OFDM. Digital data signal will be converted to analog (TX IQ) signals through DAC in BBP IC, TX IQ pass through to low pass filter. TX I/Q signal use direct conversion (zero-IF) architecture converter to generate carrier frequency signal. Transceiver IC and external PA magnify output power. 4. Receiver: Reverse direction isolation of LNA inside Transceiver IC suppresses unwanted radiation. Then 2.4GHz RF signal will be directly down to IF signal (RX IQ) and high frequency spurious emissions are suppressed by LPF. At last RX IQ signal will be demodulated digital data. 5. Base band Processing: Channel Selection: Channel selection is controlled by BBP IC. Data Modulation: DSSS (BPSK/QPSK/CCK) and OFDM (BPSK/QPSK/16QAM/64QAM) modulation type is controlled by BBP IC. Power Control Level: BBP IC has the power leveling loop table are calibrated by manufacturer, then uses closed-loop power control function to limit RF output power level. Power leveling step accuracy is ±0.5dB. Transmit/Receive Switch: EUT has Transmit/Receive Switch and Antenna switch Data Link Layer: Firmware implements the full IEEE 802.11 Wireless LAN MAC protocol. It supports BSS and IBSS operation under DCF, and operation under the optional Point Coordination Function (PCF). Lower level protocol functions such as RTS/CTS generation and acknowledgment, fragmentation and de-fragmentation, and automatic beacon monitoring are handled without host intervention. Active scanning is performed autonomously once initiated by host command. Host interface command and status handshakes allow concurrent operations from multi-threaded I/O drivers. 6. Interface: Mini PCI 7. Power: Input 3.3Vdc from host equipment. This power is provided to regulator components to regulated DC power. Report No.: FR5N2906 Report Format Version: RF-15.247-a Page No. : 3 of 51 FCC ID: MQ4WMG2501 Issued Date : Dec. 12, 2005 3. GENERAL INFORMATION 3.1. Product Details EUT IS a mini PCI card with IEEE 802.11b/g functions. Only the radio detail of WLAN is shown in the table below. For more detailed features description, please refer to the manufacturer’s specifications or user’s manual. Items Description Product Type WLAN Radio Type Intentional Transceiver Power Type 3.3 VDC from host (Notebook) Interface Type Mini-PCI Modulation DSSS for IEEE 802.11b ; OFDM for IEEE 802.11g Data Modulation DSSS (BPSK / QPSK / CCK) ; OFDM (BPSK / QPSK / 16QAM / 64QAM) Data Rate (Mbps) DSSS (1/ 2/ 5.5/11) ; OFDM (6/9/12/18/24/36/48/54) Frequency Range 2400 ~ 2483.5MHz Channel Number 11 Channel Band Width (99%) 11b: 14.80 MHz ; 11g: 16.36 MHz Conducted Output Power 11b: 19.40 dBm ; 11g: 21.50 dBm Carrier Frequencies 2412-2462 MHz Antenna Onmi-Directional Antenna 3.2. Accessories NA 3.3. Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) 1 - - Onmi-Directional Antenna Reversed-SMA 2.00

Report No.: FR5N2906 FCC ID: MQ4WMG2501 Page No. : 1 of 3 Appendix C. Maximum Permissible Exposure Report No.: FR5N2906 FCC ID: MQ4WMG2501 Page No. : 2 of 3 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 20 cm normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) ＝ d GP××30 Power Density: Pd (mW/cm²) ＝ 377 2 E E ＝ Electric field (V/m) P ＝ Peak RF output power (mW) G ＝ EUT Antenna numeric gain (numeric) d ＝ Separation distance between radiator and human body (cm) The formula can be changed to Pd ＝ 2 377 30 d GP × ×× From the peak EUT RF output power, the minimum mobile separation distance, d=20cm, as well as the gain of the used antenna, the RF power density can be obtained. Report No.: FR5N2906 FCC ID: MQ4WMG2501 Page No. : 3 of 3 1.3. Calculated Result and Limit Antenna Type : Dipole Max Conducted Power for IEEE 802.11b/g : 20dBm Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power ( mW ) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 2 1.5849 21.5000 141.2538 0.044561 1 Complies

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw Report Format Version: RF-15.247-a FCC RADIO TEST REPORT Applicant’s company AboCom Systems, Inc Applicant Address No.77, Youyi Rd., Jhunan Township, Miaoi Country 350, Taiwan FCC ID MQ4WMG2501 Manufacturer’s company AboCom Systems, Inc Manufacturer Address No.77, Youyi Rd., Jhunan Township, Miaoi Country 350, Taiwan Product Name Wireless LAN MINI PCI Card Brand Name AboCom Model Name WMG2501 Test Rule Part(s) 47 CFR FCC Part 15 Subpart C § 15.247 Test Freq. Range 2400 ~ 2483.5MHz Receive Date Nov. 14, 2005 Test Date Dec. 12, 2005 Submission Type Original Equipment Statement The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.4-2003 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Lab Code: 200079-0 Report No.: FR5N2906 Report Format Version: RF-15.247-a Page No. : i of ii FCC ID: MQ4WMG2501 Issued Date : Dec. 12, 2005 Table of Contents 1. CERTIFICATE OF COMPLIANCE ............................................................................................................................ 1 2. SUMMARY OF THE TEST RESULT ............................................................................................................................. 2 3. GENERAL INFORMATION ..................................................................................................................................... 3 3.1. Product Details ....................................................................................................................................................................................3 3.2. Accessories .........................................................................................................................................................................................3 3.3. Table for Filed Antenna .......................................................................................................................................................................3 3.4. Table for Carrier Frequencies...............................................................................................................................................................4 3.5. Table for Test Modes............................................................................................................................................................................4 3.6. Table for Testing Locations...................................................................................................................................................................4 3.7. Table for Supporting Units ....................................................................................................................................................................5 3.8. Table for Parameters of Test Software Setting.......................................................................................................................................5 3.9. Test Configurations ..............................................................................................................................................................................6 4. TEST RESULT ......................................................................................................................................................... 8 4.1. AC Power Line Conducted Emissions Measurement............................................................................................................................8 4.2. Maximum Peak Output Power Measurement ....................................................................................................................................12 4.3. Power Spectral Density Measurement ...............................................................................................................................................14 4.4. 6dB Spectrum Bandwidth Measurement ...........................................................................................................................................19 4.5. Radiated Emissions Measurement.....................................................................................................................................................24 4.6. Band Edge Emissions Measurement..................................................................................................................................................42 4.7. Antenna Requirements......................................................................................................................................................................47 5. LIST OF MEASURING EQUIPMENTS....................................................................................................................... 48 6. SPORTON COMPANY PROFILE ........................................................................................................................... 50 6.1. Test Location .....................................................................................................................................................................................50 7. CERTIFICATE OF NVLAP ACCREDITATION ............................................................................................................ 51 APPENDIX A. PHOTOGRAPHS OF EUT ............................................................................................................. A1 ~ A5 APPENDIX B. TEST PHOTOS ................................................................…

Text truncated - open the document above for the full version.

Report No.: FR5N2906 FCC ID: MQ4WMG2501 Page No. : 1 of 3 Appendix B. Test Photos Report No.: FR5N2906 FCC ID: MQ4WMG2501 Page No. : 2 of 3 1. Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW Report No.: FR5N2906 FCC ID: MQ4WMG2501 Page No. : 3 of 3 2. Photographs of Radiated Emissions Test Configuration FRONT VIEW REAR VIEW