MSAB17AC17" CCTV MONITOR

TFT-LCD Color MonitorH750V(B17AC) // H950V(B19AC) Printed on the recyclable paper Printed in ThailandPart No. 942667020001 - 01 Users Manual Parts 3 Connection to Signal Source 4 The range of control Angle 5 Name and Function of Front 6 Power Management Feature 8 Adjusting OSD 9 Standard Signal Table 22 Specification 24 Troubleshooting 26 Warning 28 Table of Contents INFORMATION TO USER : This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses and canradiate radio frequency energy and,if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation; if this equipment does cause harmful interference to radio ortelevision reception, which can be determined by determined by turning theequipment off and on, the user is encouraged to try to crrent the interference byone or more of the fllowing measures: 1. Reorient/Relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit difference from that to which the recerver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. CAUTION Changes or modifications not expressly approved by themanufacturer responsible for compliance could void the user's authority to operate the equipment ENERGY STAR As an ENERGY STAR partner, Hansol Electronics Inc. has determined that this product meets energy Star guidelines for energy efficiency. English - 3 2 - English Parts 17 " LCD Monitor Place the monitor to face the user and then adjust the monitor angle.Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cm Look down the monitor below the horizon. Relax shoulders and arms, and sit back on the chair. Adjust the monitor to prevent reflection. Adjust the monitor stand to acquire required angle. Keep feet flat on the ground. Maintain the arms horizontally and place hands softly on the keyboard. Good Posture Guide User's Manual / Warranty Card Signal Cable AC Power Cable Stereo Cable(Option) 19 " LCD Monitor English - 5 4 - English Connection to Signal Source 1. Use 220 V or 110 V. (Free Voltage)2. Connect monitor and Signal Source via Signal cable3. Power on the monitor and computer.4. Connection is finished. General For Macintosh Adapter for Macintosh (Optional)Refer to the table on the rear side ofthe optional Macintosh adapter andadjust DIP switch by the resolution. T he range of control Angle < Power source connection > < Signal cable connection> Basic Connection Port for AC power cable.Port for BNC outputPort for BNC inputPort for S-VHS input Port for Audio inputKensington LockPort for signal cable from signal source. How to Adjust the Stand Forward 3 Default Backward 30 +/ -/ English - 7 6 - English Power button Power button is located in the lower center of the Front Bezel.You can push the button to turn on/off the power. Power Indicating LED Dark : Power off Green : Normal modeGreen blinking : DPMS mode or Check Signal Cable mode. On Screen Display (OSD) Function Button OSD buttons on the front of bezel perform the following functions. SOURCE : Monitor displays source of the signal in order ( PC CVBS S-VHS ) MENU/EXIT : Press this button to display menus. if you press this button when OSD is displayed, you can switch display to the previous menu and exit menu. SELECT/ AUTO : Press this button, when OSD is not displayed, to perform automatic setting. (only PC Mode.) When OSD is displayed, You can select icons. POWER : Power button. : By pressing these button when OSD is displayed, You can move cursor into the menus which you want. After press the SELECT button, you can change gauge level or select submenus.When OSD is not displayed, you can adjust brightness or contrast. VOLUME / MUTE : Press this button for volume control. when control is displayed, You can control mute by pressing this button Name and Function of Front Front panel Functions SELECT/ AUTO BUTTON MENU/EXIT BUTTON SOURCE BUTTON VOL / MUTE BUTTON / + BUTTON POWER BUTTON (Power indicating LED) / - BUTTON 17 " LCD Monitor 19 " LCD Monitor English - 9 8 - English No image is displayed with Green blinking. Monitor is in power saving mode.Use mouse or keyboard to release power saving mode. No image is displayed without LED on. Power cable plug must be pulled out.Check the power plug on monitor and on the wall. "Out of range" displayed on the screen. This message is displayed when the signal from video card exceeds themaximum frequency of the monitor. Readjust resolution and frequency inaccordance with the monitor capacity. (Refer to Standard Signal Table) Power Management Feature The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling(DPMS) mode of Video Electronics Standard Association (VESA).The power management feature requires that the video card of thecomputer should support DPMS function. Adjusting OSD - PC MODE Brightness Contrast 1. Use to move Brightness ICON. 2. Press SELECT button to select it.3. Use to adjust the brightness of the screen. SELECT Brightness / Contrast MENU 1. Press the MENU button to access main menu.2. Use to move Brightness / Contrast ICON. 3. Press SELECT button into the submenu. SELECT SELECT 1. Use to move Contrast ICON. 2. Press SELECT button to select it.3. Use to adjust the contrast of the screen. Status LED Sign Power Consumption Normal mode Green ON Normal Power DPMS mode Green Blinking 3W or Below DPMS with Audio Mute ON 3W or Below Mute OFF 5W or Below English - 11 10 - English Horizontal Position SELECT 1. Use to move H-Positi…

Text truncated - open the document above for the full version.

AUDIO OSD CONTROLS TFT-LCD Color Monitor H750V(B17AC) // H950V(B19AC)

Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 23 of 36 APPENDIX D – EUT PHOTOGRAPHS
Front View of EUT Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 24 of 36
Rear View of EUT

Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 19 of 36 APPENDIX A – SAMPLE LABEL The sample label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase.
FCC ID Location of EUT Labelling Requirements

Made in THAILAND HT Manufactured: CAUTION TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE COVER, NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION, NE PAS ENLEVER L’ARRIERE. AUCUNE PIECE REPARABLE PAR L’USAGER A L’INTERIEUR. POUR REPARATIONS, APPELER UN TECHNICIEN QUALIFIE. This Class B digital apparatus complies with Canadian ICES-003. APPARATET Må KUN TILKOPLES JORDET STIKKONTAKT. Apparaten skall anslutas till jordat uttag n ä r den ansluts till ett n ä tverk. FCC ID : MSA B17AC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference and 2) This device must accept any interference received, including interference that may cause undesired operation. MODEL Name : H750V MODEL No. : B17AC ELECTRICAL RATING AC 100 -240V 50/60 Hz, 0.6A Hansol LCD Inc. 27-29 Hanchon-Ri Duksan-Myun Jinchon-Kun Choongbuk, KOREA

Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 25 of 36
Inside View of EUT1 Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 26 of 36
Inside View of EUT2 Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 27 of 36
Front View of Main Board Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 28 of 36
Rear View of Main Board Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 29 of 36
Front View of OSD Board Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 30 of 36
Rear View of OSD Board Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 31 of 36
Front View of Combo Board Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 32 of 36
Rear View of Combo Board Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 33 of 36
Front View of LCD Panel Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 34 of 36
Rear View of LCD Panel

A A B B C C D D E E 44 33 22 11 ADC_ 3AVCC TMDS_3AVCC RTD 3DVCC RTD 2.5DVCC RTD 3PVCC Not Mount RTD2522_DE_BA Power C 16Thursday, October 02, 2003 Title SizeDocument NumberRev Date:Sheetof MOD_ON BL_ON INV_PWM MOD_PWR 5V 3AVCC1 5V12V 2.5DVCC 3PVCC 3D_VCC 3.3VD 3.3VA2 3AVCC2 2.5VDD 5V3.3VDD 5V U1 GS1086-3.3V/TO-263 32 4 1 VINVOUT TAB GND U4SI3863/SOT-23-6L 3 2 1 5 6 4 VOUT2 VOUT1 GND ON/OFF G VIN FB12300 12 U2 LM1117-2.5V/SOT23 32 4 1 VINVOUT TAB GND + - C17 47uF/16V R1 4.7K CN1 SMW200-8 1 2 3 4 5 6 7 8 FB6300 R3100R C8 0.1uF + - C26 47uF/16V + C1 47uF/16V C18 0.1uF 1 2 + - C5 47uF/16V C9 100uF/16V + C7 47uF/16V + - C22 47uF/16V FB1300 R733K FB3300 C4 0.1uF 1 2 R6 47K FB7300 FB5300 + - C20 47uF/16V C6 0.1uF 1 2 FB4300 C27 0.1uF 1 2 + - C14 47uF/16V +C2 47uF/16V FB2300 U3 LM1117-3.3V/SOT23 32 4 1 VINVOUT TAB GND FB8300 FB11300 12 C23 0.1uF 1 2 + - C3 47uF/16V C11 100uF/16V R5 4.7K C12 22uF/16V C25 1000pF 1 2 FB9300 C10 0.1uF + C13 47uF/16V C21 0.1uF 1 2 + - C15 47uF/16V + - C19 47uF/16V FB10300 R4 4.7K C16 0.1uF 1 2 R8 4.7K + - C24 47uF/16V R2150R A A B B C C D D E E 44 33 22 11 Not Mount RTD2522_DE_BA MCU/MTV512 C 26Thursday, October 02, 2003 Title SizeDocument NumberRev Date:Sheet of RST INV_PWM VOL_PWM KEY LED KEY1 KEY KEY1 STBY MUTE_CTRL LED ST_DET BL_ON MOD_ON IICSCL IICSDA CCVALID VDLOSS DDC_SDA DDC_SCL RTD_SCSB RTD_SCL RTD_SDO/SDI RTD_RESET IICSDA IICSCL 5V 5V 5V 5V 3.3VDD ZD3 BZX84C5V6 1 3 2 R14 10K R15 10K R16 47K R21 47K R23240R R9 4.7K R32100R R24240R C30 0.1uF R29240R 100RR37 C34 0.1uF 1 2 R36100R R38 1M R30240R R40 330R R31100R R34240R J1 OSD Key Connector 1 2 3 4 R27240R R43100R R35240R R13 4.7K C36 0.1uF 1 2 Y1 12M/crystal R25240R R41100R R12 4.7K R11 4.7K R20 4.7K C33 0.1uF R18 4.7K R42100R R10 4.7K R28240R C35 0.1uF 1 2 U6 X24C16 8 5 6 4 7 3 2 1 5DVCC SDA SCL GND TEST A2 A1 A0 R44 47K C32 22pF R39 0R R26240R C31 22pF R19 4.7K U5 MTV612 2 3 4 5 6 7 8 9 10 11 202122 444342414039383736 35 32 33 24 25 26 27 28 29 30 31 13 14 15 16 17 18 19 12 P5.0/DA0 P5.1/DA1 P5.2/DA2 P5.3/DA3 P5.4/DA4 P5.5/DA5 HSCL2/P5.6 HSDA2/P5.7 RST P3.0 XTAL2XTAL1VSS VCC P1.0P1.1P1.2P1.3P1.4P1.5P1.6P1.7 NC VSYNC NC P6.0/AD0 P6.1/AD1 P6.2/AD2 P6.3/AD3 P6.4 P6.5 P6.6/CLKO P6.7 P3.1 P3.2 P3.3 P3.4 P3.5 P7.6/CLKO P7.7 NC ZD2 BZX84C5V6 1 3 2 R22 10K R33240R R17 4.7K + C29 10uF/16V + C28 22uF/16V ZD1 BZX84C5V6 1 3 2 5 5 4 4 3 3 2 2 1 1 DD CC BB AA TMDS VDD PLL_VDD . DVI , DVI . Not Mount Not Mount Not Mount RTD2522_DE_BA RTD_2522 Custom 36Thursday, October 02, 2003 Title SizeDocument NumberRev Date:Sheet of RXOIN3+ RXOIN3- RXOCKIN+ RXOCKIN- RXOIN2+ RXOIN2- RXOIN1+ RXOIN1- RXOIN0+ RXOIN0- RXEIN3+ RXEIN3- RXECKIN+ RXECKIN- RXEIN2+ RXEIN2- RXEIN1+ RXEIN1- RXEIN0+ RXEIN0- V7 V5 V4 V6 V2 V1 V0 PLL_GND V3 DDC_SDA DDC_SCL RXECKIN- RXEIN2+ RXEIN2- RXECKIN+ RXEIN3- RXEIN3+ RXEIN1+ RXEIN1- RXEIN0+ RXEIN0- RXOCKIN- RXOIN3+ RXOIN3- RXOCKIN+ RXOIN2- RXOIN1- RXOIN0+ RXOIN2+ RXOIN1+ RXOIN0- RTD_SCSB RTD_SCL RTD_RESET V[0..7] RTD_SDO/SDI CLK_DEC ST_DET DDC_SCL DDC_SDA 3.3VDD 3AVCC1 3AVCC2 3D_VCC 3PVCC 2.5DVCC 5V 5V MOD_PWR C38 12pF C610.047uF C640.047uF +C80 47uF/16V C72 0.1uF C85 0.1uF C5822pF C44 0.1uF C84 0.1uF C56 0.1uF R55100R C81 0.1uF R48 4.7K C71 0.1uF R51100R C48 0.1uF C69 0.1uF 100RR61 R49 0R L1FEB_0603 C46 0.1uF RTD2022 373810911158616263 105 107 41 42 43 46 47 48 51 52 53 103 88 94 92 93 98 97 102 100 101 91 95 90 89 123 122 1 2 125 126 119 118 120 117 121 124 128 127 395060106404959110113333454641041083235556586874544 112 115116 70 73 72 71 74 75 76 77 78 79 80 81 85 82 83 84 69 68 67 66 5756 5 6 7 8 9 10 11 12 13 14 19 20 21 22 23 24 25 26 27 28 4172918315163031 99 96 114 36 PWM2/TCON[1]PWM1/REF_CLKDDC_SCLDDC_SDASDIOSCLKSCSBRESET# AHS AVS V0 V1 V2 V3 V4 V5 V6 V7 VCLK GUARD_VDD GUARD_GND ADC_B_VDD ADC_B_GND B SOG G ADC_R_VDD ADC_R_GND R ADC_VDD ADC_GNDOFF ADC_REFIO ADC_GND PLL_TEST1 / IRQ U7 PLL_TEST2 XO XI DPLL_VDD DPLL_GND APLL1_VDD APLL1_GND APLL2_VDD APLL2_GND APLL3_VDD APLL3_GND PLL_GUARD_VDD PLL_GUARD_GND GNDIOGNDIOGNDIOGNDIO VCC33VCC33VCC33VCC33 GNDIO GNDKGNDKGNDKGNDKGNDK VCCKVCCKVCCKVCCKVCCKVCCK GNDKGNDK VCCK PWM0 VCCK GNDK TMDS_VDD2 TMDS_GND2 RX2N RX2P TMDS_VDD1 RX1P RX1N TMDS_GND1 TMDS_VDD0 RX0P RX0N TMDS_GND0 TMDS_PLL_VDD RXCP RXCN TMDS_PLL_GND REXT TMDS_VDD TMDS_GND TMDS_TST DDC2_SCLDDC2_SDA TODP TODN TOCLKP TOCLKN TOCP TOCN TOBP TOBN TOAP TOAN TEDP TEDN TECLKP TECLKN TECP TECN TEBP TEBN TEAP TEAN LVDS_GNDLVDS_PLL_GNDLVDS_GNDLVDS_GNDLVDS_VDDLVDS_VCCLVDS_PLL_VCCLVDS_VCCLVDS_TST ADC_G_VDD ADC_G_GND TCON[0] GNDK L3 FEB_0603 C47 0.1uF C43 0.1uF 31 ZD4 BZX84C5V6 C6322pF C45 0.1uF C68 0.1uF C6622pF C670.1uF R62100R R G B NC DGND RAGND GAGND BAGND NC DGND NC DDCSDA DDCSCL HSIN VSIN U8 VGA_CON15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 R5075R C74 0.1uF R46100R 31 ZD5 BZX84C5V6 R54100R C75 0.1uF FB13300 C37 22pF R53100R C49 0.1uF C76 0.1uF CN2 12507WR-30 / 1.25mm 1 2 3 4 6 8 10 12 14 16 18 20 22 24 26 28 30 7 9 11 13 15 17 19 21 23 25 27 29 5 C54 0.1uF C77 0.1uF C51 0.1uF C42 0.1uF C53 0.1uF C40 0.1uF C575pF C73 0.1uF C50 0.1uF C52 0.1uF C39 0.1uF C655pF C55 0.1uF C605pF + C86 10uF/16V C41 0.1uF R59 10K 31 D1 BZX84C5V6 R47 4.7K D5 R57 1M C79 22pF C620.047uF R60100R R45100R C78 22pF L2FEB_0603 +C82 47uF/16V Y2 24.576MHz R5675R FB15300 FB14300 R580R D2 BAV99/SOT23 1 3 2 R5275R D3 BAV99/SOT23 1 3 2 C70 0.1uF C83 0.1uF C590.047uF D4 BAV99/SOT2 3 1 3 2 5 5 4 4 3 3 2 2 1 1 DD CC BB AA X201: GND , Decoder Not Mount <Doc><RevCode> <Title> C 46Thursday, October 02, 2003 Title SizeDocument NumberRev Date:Sheet of V4 V6 V0 V3 V7 V2 V1 V5 VDLOSS CCVALID Y_IN CLK_DEC IICSDA IICSCL V[0..7] SVHSY SVHSC DVCC 3.3VA2 DVCC 3.3VD DVCC 3.3VA2 DVCC C98 0.1uF 1 2 C870.1uF 12 C102 0.1uF 1 2 C88 22pF 12 C104 0.1uF 1 2 C940.1uF 12 R69 75R + C97 10uF/16V 1 2 C101 0.1uF 1 2 C107 0.001uF 1 2 C103 0.1uF 1 2 TST1 1 C99 0.1uF 1 2 R7010k C93 0.1uF 1 2 L7 BEAD-50 12 C106 0.1uF 1 2 C92 0.1uF 1 2 C105 0.1uF 1 2 R6533R U9 TW9905 9798100 1 3 4 6 7 60 61 63 64 68 69 71 729 10 12 13 17 18 20 21 74 75 77 78 80 818384 3132333447484950 3051 29 27 26 25 28 5…

Text truncated - open the document above for the full version.

Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 1 of 36 Nemko Korea Co., Ltd. 300-2, Osan-Ri, Mohyun-Myun, Yongin-City, Kyungki-Do, KOREA TEL:+82 31 322 2333 FAX:+82 31 322 2332 FCC EVALUATION REPORT FOR CERTIFICATION Applicant : Hansol LCD Inc. Dates of Issue :October 22, 2003 #27-29, Hancheon-Ri, Ducksan-Myun, Test Report No. : NK2DE644 Jincheon-Gun, Choongbuk, Korea Test Site : Nemko Korea Co., Ltd. Attn : Mr. W. S. Lee EMC site, Korea FCC ID Brand Name Contact Person Applied Standard: FCC 47 CFR Part 15, Subpart B : 2000 Classification : FCC Class B Device EUT Type: 17” CCTV Monitor The device bearing the brand name and FCC ID specified above has been shown to comply with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.4-1992. I attest to the accuracy of data and all measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Tested By : J. H. Ko Reviewed By : H.H. Kim Engineer Manager & Chief Engineer MSAB17AC Hansol Hansol LCD Inc. #27-29, Hancheon-Ri, Ducksan-Myun, Jincheon-Gun, Choongbuk, Korea Mr. W. S. Lee Telephone No. : +82 43 530 8554 Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 2 of 36 TABLE OF CONTENTS SCOPE INTRODUCTION (Site Description) TEST CONDITIONS & EUT INFORMATION SUMMARY OF TEST RESULTS RECOMMANDATION / CONCLUSION SAMPLE CALCULATION DESCRIPTION OF TESTS (Conducted Emissions) DESCRIPTION OF TESTS (Radiated Emissions) TEST DATA (Conducted Emissions) TEST DATA (Radiated Emissions) PLOT OF EMISSIONS (Conducted Emissions Diagram) ACCURACY OF MEASUREMENT TEST EQUIPMENT APPENDIX A - LABELLING REQUIREMENTS APPENDIX B - CIRCUIT DIAGRAM APPENDIX C - PHOTOGRAPHS OF TEST SET-UP APPENDIX D - EUT PHOTOGRAPHS APPENDIX E - USER’S MANUAL APPENDIX F - SCHEMATIC DIAGRAM 3 4 5 7 7 7 8 9 10 11 13 17 18 19 20 21 23 35 36 Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 3 of 36 SCOPE Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission under FCC part 15. Responsible Party : Contact Person : Manufacturer : Factory : Hansol LCD Inc. Mr. W. S. Lee Tel No.: +82 43 530 8554 Hansol LCD Inc. #27-29, Hancheon-ri, Ducksan-Myun, Jincheon-Gun, Choongbuk, Korea Tel No.: +82 43 530 8554 Hansol Electronics (Thailand) Co., Ltd. 168 Moo 1 Tambon Banbung, Amphoe Banbung, Chonburi Province 20170 Thailand
FCC ID: MSAB17AC
Model: B17AC
Brand Name: Hansol
EUT Type: 17” CCTV Monitor
Electric Rating: 100-240V AC, 50/60Hz, 0.6A
Port/Connector: D-Sub, S-Video In, BNC In/Out, Stereo Audio In
Classification:
Applied Standard:
Test Procedure(s):
Dates of Test:
Place of Tests:
Test Report No.: FCC Class B FCC 47 CFR Part 15 , Subpart B ANSI C63.4 (1992) October 14, 2003 to October 18,2003 Nemko Korea Co., Ltd. EMC Site NK2DE644 Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 4 of 36 INTRODUCTION The measurement procedure described in American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40GHz (ANSI C63.4-1992) was used in determining radiated and conducted emissions emanating from Hansol LCD Inc. FCC ID : MSAB17AC, 17” CCTV Monitor. These measurement tests were conducted at Nemko Korea Co., Ltd. EMC Laboratory . The site address is 300-2, Osan-Ri, Mohyun-Myun, Yongin-City, Kyungki-Do, KOREA The area of Nemko Korea Corporation LTD. EMC Test Site is located in a mountain area at 80 kilometers (48 miles) southeast and Incheon International Airport (Incheon Airport), 30 kilometers (18miles) south-southeast from central Seoul. It is located in the valley surrounded by mountains in all directions where ambient radio signal conditions are quiet and a favorable area to measure the radio frequency interference on open field test site for the computing and ISM devices manufactures. The detailed description of the measurement facility was found to be in compliance with the requirements of
2.948 according to ANSI C63.4 on October 19, 1992. Fig. 1. The map above shows the Seoul in Korea vicinity area. The map also shows Nemko Korea Corporation Ltd. EMC Lab and Incheon Airport. Nemko Korea Co., Ltd. OPEN AREA TEST SITE 300-2, Osan-Ri, Mohyun-Myun, Yongin- City Kyungki-Do,KOREA 449-852 Tel)+82-31-322-2333 Fax)+82-31-322-2332 Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 5 of 36 TEST CONDITIONS & EUT INFORMATION Operating During Test The EUT was operated by the software. The PC sent “H” pattern to monitor(EUT) and The monitor displayed “H” pattern on screen. It also sent “H” pattern to printer, then the printer printed it out. This software had above all functions conduct in order. And a audio signal from HDD was played continuously. The EUT were connected to CCD camera, then the video signal of CCD camera captured was sent to the EUT(CCTV Monitor). The EUT was displayed continuously the video signal on screen. EUT & Support Equipment 17” CCTV Monitor (EUT) Hansol, FCC ID: MSAB17AC 1.5m unshielded AC power cable 1.8m shielded D-sub cable 1.8m shielded BNC Composite cable 1.8m shielded Din S-Video cable 1.0m unshielded Stereo Jack cable S/N: N/A PC Dell Computer,Model: Precision 340 1.8m unshielded AC power cable S/N: N/A PS/2 Mouse Microsoft Corp., Model: X06-08477 1.5m unshielded Din cable S/N: N/A Serial Mouse ALLSPIRIT, Model: WS-V1-400 1.5m unshielded Dsub cable S/N: B05002 Keyboard Silitek Yet Foundate, Model: SK-8110 1.8m unshielded…

Text truncated - open the document above for the full version.

Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 21 of 36 APPENDIX C – PHOTOGRAPHS OF TEST SET-UP The Conducted Test Picture and Radiated Test Picture and show the worst-case configuration and cable placement.
Conducted Test Picture(Front)
Conducted Test Picture(Rear) Test Report No.: NK2DE644 FCC Certification Hansol LCD Inc. FCC ID:MSAB17AC Page 22 of 36
Radiated Test Picture(Front)
Radiated Test Picture(Rear)