MSQ-ASUSNFC-PN544NFC Sensor Module

ASUS NFC-PN544 MODULE User Manual I. Introduction: ASUS NFC-PN544 is a module equipped with both NFC and USB3.0 Hub functions. It can be connected to Windows based systems by USB3.0 A to A type cable. The USB3.0 Hub is activated by embedded driver of Intel chipset(PCH) and the NFC is activated by NXP provided driver(only available on Win8) II. Design Reference: ASUS NFC-PN544 is composed as the following: a) USB3.0 hub IC: This section includes Asmedia ASM1074 chip and its external components completed refer to the reference design. An addtional EEPROM is utilized to store the corresponding FW. Note this module only applies bus power from USB port. b) NFC IC: This section includes NXP PN544 C3 chip and the external components completed refer to the reference design. The antenna design is also based on the refernce design of NXP PN544 demo board(schematic, layout, BOM etc). The driver provided by NXP is applicable only on Windows 8. c) USB to UART convertor IC: Exar XR21B1411 is adopted to bridge from USB3.0 Hub IC to NFC IC, PN544C3 communicates with the connected system by UART interface. The driver is available on line. d) 1 A type USB3.0 upstream port connector: the main connection port to a Windows based system, an A to A type USB3.0 cable is necessary. e) 2 A type USB3.0 downstream port connectors: for external devices certificated by USB compliance, and are applicable up to USB3.0. f) 5 white LEDs: to indicate the power of USB bus is on. Note: there is no external power design for this module, heavy loading behaviors (ex. 2 USB removable HDDs data R/W concurrently) on USB devices is not advised. III. Feature: Contactless protocols: ISO14443A/B, ISO15693, ISO18092 USB compliance: USB3.0, USB2.0, USB1.1 IV. Spec sheet: Antenna: On board PCB trace (size 32mm*54mm), basically a loop coil, formed by PCB trace Operating frequency: 13.56MHz Data rate: up to 848kbps Modulation: Manchester, ASK, BPSK V. Product Overview FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. Labeling requirements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: MSQ-ASUSNFC-PN544 ” and "Contains IC: 3568A-ASNFC-PN544“ Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions.

Report No.: 134385R-RFUSP39V01 Page : 1 of 3 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo Antenna

ASUSTeK COMPUTER INC. FCC ID.: MSQ-ASUSNFC-PN544 4F, No. 150, Li-Te Rd., Peitou, Taipei, Taiwan Tel : 886-2-2894-3447 FCC ID Label

ASUSTeK COMPUTER INC. FCC ID.: MSQ-ASUSNFC-PN544 4F, No. 150, Li-Te Rd., Peitou, Taipei, Taiwan Tel : 886-2-2894-3447 The FCC ID and Doc Label will be placed on the equipment as shown in the photograph below.

Report No.: 134385R-RFUSP39V01 Page : 2 of 3 (3) EUT Photo (4) EUT Photo Report No.: 134385R-RFUSP39V01 Page : 3 of 3 (5) EUT Photo (6) EUT Photo

Report No. 134385R-RFUSP39V01 Page: 1 of 26 FCC Test Report Product Name NFC sensor Module Model No. ASUS NFC-PN544 FCC ID MSQ-ASUSNFC-PN544 Applicant ASUSTeK COMPUTER INC. Address 4F, No. 150, Li-Te Rd., Peitou, Taipei, Taiwan Date of Receipt Apr. 19, 2013 Issued Date May 08, 2013 Report No. 134385R-RFUSP39V01 Report Version V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Report No. 134385R-RFUSP39V01 Page: 2 of 26 Test Report Certification Issued Date: May 08, 2013 Report No.: 134385R-RFUSP39V01 Test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Product Name NFC sensorModule Applicant ASUSTeK COMPUTER INC. Address 4F, No. 150, Li-Te Rd., Peitou, Taipei, Taiwan Manufacturer NBM Production(DongGuan)Co.,Ltd. Model No. ASUS NFC-PN544 FCC ID. MSQ-ASUSNFC-PN544 EUT Rated Voltage DC 5V (by USB) EUT Test Voltage AC 120V/60Hz Trade Name ASUS Applicable Standard FCC CFR Title 47 Part 15 Subpart C: 2012 ANSI C63.4: 2003, ANSI C63.10: 2009 Test Result Complied Documented By : (Senior Engineering Adm. Specialist / Anita Chou) Tested By : ( Engineer / Andy Lin ) Approved By : ( Manager / Vincent Lin ) Report No. 134385R-RFUSP39V01 Page: 3 of 26 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .....................................................................................................4 1.1. EUT Description............................................................................................................................4 1.2. Operational Description ................................................................................................................5 1.3. Tested System Datails....................................................................................................................6 1.4. Configuration of tested System .....................................................................................................6 1.5. EUT Exercise Software .................................................................................................................7 1.6. Test Facility ...................................................................................................................................8 2. Conducted Emission....................................................................................................................9 2.1. Test Equipment..............................................................................................................................9 2.2. Test Setup ......................................................................................................................................9 2.3. Limits ..........................................................................................................................................10 2.4. Test Procedure .............................................................................................................................10 2.5. Uncertainty ..................................................................................................................................10 2.6. Test Result of Conducted Emission.............................................................................................11 3. Radiated Emission .....................................................................................................................13 3.1. Test Equipment............................................................................................................................13 3.2. Test Setup ....................................................................................................................................13 3.3. Limits ..........................................................................................................................................14 3.4. Test Procedure .............................................................................................................................15 3.5. Uncertainty ..................................................................................................................................16 3.6. Test Result of Radiated Emission................................................................................................17 4. Band Edge ..................................................................................................................................20 4.1. Test Equipment............................................................................................................................20 4.2. Test Setup ....................................................................................................................................20 4.3. Limits ..........................................................................................................................................21 4.4. Test Procedure .............................................................................................................................21 4.5. Uncertainty ..................................................................................................................................21 4.6. Test Result of Band Edge ............................................................................................................22 5. Frequency Tolerance .................................................................................................................23 5.1. Test Equipment............................................................................................................................23 5.2. Test Setup ..............…

Text truncated - open the document above for the full version.

Report No.: 134385R-RFUSP39V01 Page : 1 of 3 Attachment 1: EUT Test Setup Photographs Front View of Conducted Test Back View of Conducted Test Report No.: 134385R-RFUSP39V01 Page : 2 of 3 Front View of Radiated Test Back View of Radiated Test Report No.: 134385R-RFUSP39V01 Page : 3 of 3 Front View of Radiated Test Back View of Radiated Test