MSQ-RPAX4W00Dual-Band Wireless Repeater

Placing your RP-AX56 Plug your RP-AX56 into a power outlet near your router/AP. Check the LEDs and see the LED explanations. METHOD 1 Download the ASUS Extender App METHOD 2 Connect via WPS Press the WPS button on your router/ A P. Press the WPS button on your RP-AX56 for more than two (2) seconds until the LED starts to blink blue. RP-AX56 Dual-Band Wireless Repeater Quick Start Guide Hardware Explanations Button Explanations RESET BUTTON Reset the system to its factory default settings. WPS BUTTON Launch the WPS Wizard. LAN PORT Connect your PC to the LAN port with a network cable. BEFORE SETUP SETUP METHODS WE SUGGEST... Set up RP-AX56 as a repeater 1 Plug RP-AX56 into a power outlet. 2 The LED will start breathing white for 3 seconds while booting up. LAN port LED WPS button reset button LED Explanations Repeater Mode StatusLED Behavior Booting upBlinking White Booting up complete (haven’t connected to Router) Solid Blue Reset (use a pin to press the reset button for 5 seconds) Blinking Yellow Rescue modeSolid Purple Starting WPSBlinking Blue Connected to the router with Good Signal Solid White Conneccted to the router with Weak Signal Solid Yellow No SignalSolid Red AP mode (with wired connection) Solid White AP mode (without wired connection) Solid Red AiMesh Mode StatusLED Behavior Booting upBlinking White Booting up complete (not connected to AiMesh Router) Solid Blue Reset (use a pin to press the reset button for 5 seconds) Blinking Yellow Rescue modeSolid Purple Connecting to the AiMesh RouterBlinking Blue Connected to the AiMesh Router with Good Signal Solid White Connected to the AiMesh Router with Weak Signal Solid Yellow No SignalSolid Red Ethernet backhaulSolid White Wait for the LED to flash and turn solid blue, indicating that your RP-AX56 is ready to connect to your existing router/AP. around 2 meters 3 If you would like to connect RP-AX56 to other WiFi networks excluding AiMesh-supported routers, please download the ASUS Extender App. 12 01 12 If your AiMesh router cannot find RP-AX56 nearby or synchronization fails, please check followings and try again. i. Download AiMesh - supported fireware at: https://www.asus.com/AiMesh/. ii. Launch a web GUI. You will be redirected to the ASUS Setup Wizard. If not, navigate to http://router. asus.com. iii. Go to Administration > Firmware Upgrade. Click Choose File, and upload the AiMesh-supported firmware. iv. After the firmware is uploaded, please go to the Network Map page to check and make sure that the AiMesh icon shows up. v. Use a pin to press the reset button on your RP-AX56 for at least 5 seconds. Release the reset button when the power LED is flashing slowly. 優優優優 Q1 A: Yes. AiMesh system supports both wireless and wired connection between an AiMesh router and node to maximize throughput and stability. AiMesh analyzes the wireless signal strength for each frequency band available, and then determines automatically whether a wireless or wired connection is best to serve as the inter-router connection backbone. To know more about ASUS AiMesh, please go to https://www.asus.com/AiMesh/. RELOCATION FAQ TROUBLE SHOOTING THE BEST PERFORMANCE FREQUENTLY ASKED QUESTIONS a Plug RP-AX56 into a power outlet near your router/AP. Ensure that it is within 3 meters from the AiMesh router. b Your AiMesh router is upgraded to AiMesh- supported firmware. Locate the AiMesh router and RP-AX56 at best place. NOTES: • To minimize interference, keep the routers away from devices like cordless phones, Bluetooth devices and microwave ovens. • We recommend that you place the routers in an open or spacious location. Could I setup wired connection between AiMesh routers and nodes (Ethernet backhaul)? 1 Follow the setup steps to establish a connection between the AiMesh router and RP-AX56 via WiFi first. 2 Place the RP-AX56 in an ideal location for the best coverage. Run an Ethernet cable from the LAN port of the AiMesh router to the Ethernet backhaul port of RP- AX56. 3 AiMesh system will auto-select the best path for data transmission, whether wired or wireless. ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling information in different regions. REACH Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital de- vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circui…

Text truncated - open the document above for the full version.

ASUSTeK COMPUTER INC. 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan Date: 2020-05-27 FCC ID: MSQ-RPAX4W00 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Jackson Yen / Associate Vice President ASUSTeK Computer Inc. Tel: +886-2-28943447 Fax: +886-2-28987364 E-mail: [email protected]

ASUSTeK COMPUTER INC. 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan Date: 2020-05-29 FCC ID: MSQ-RPAX4W00 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------------------- Jackson Yen / Associate Vice President ASUSTeK Computer Inc. Tel: +886-2-28943447 Fax: +886-2-28987364 E-mail: [email protected]

ASUSTeK COMPUTER INC. 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan Date: 2020-05-27 FCC ID: MSQ-RPAX4W00 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: ASUSTeK COMPUTER INC. hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan onASUSTeK COMPUTER INC.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- Jackson Yen / Associate Vice President ASUSTeK Computer Inc. Tel: +886-2-28943447 Fax: +886-2-28987364 E-mail: [email protected]

Reference No.: 200407C10 1 CONSTRUCTION PHOTOS OF EUT Reference No.: 200407C10 2 Reference No.: 200407C10 3

Reference No.: 200407C10 1 CONSTRUCTION PHOTOS OF EUT WLAN Ant. Reference No.: 200407C10 2 Reference No.: 200407C10 3 Reference No.: 200407C10 4 Reference No.: 200407C10 5 Reference No.: 200407C10 6 Reference No.: 200407C10 7 Reference No.: 200407C10 8

Report No.: SA200407C10 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: SA200407C10 FCC ID: MSQ-RPAX4W00 Test Model: RP-AX56 Received Date: Apr. 07, 2020 Date of Evaluation: Jun. 01, 2020 Issued Date: Jun. 10, 2020 Applicant: ASUSTek COMPUTER INC. Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim any endorsement by TAF. Report No.: SA200407C10 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 2.4 Calculation Result of Maximum Conducted Power ............................................................................. 6 Report No.: SA200407C10 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA200407C10 Original Release Jun. 10, 2020 Report No.: SA200407C10 Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: Dual-Band Wireless Repeater Brand: ASUS Test Model: RP-AX56 Sample Status: Engineering Sample Applicant: ASUSTek COMPUTER INC. Date of Evaluation: Jun. 01, 2020 Standards: FCC Part 2 (Section 2.1091) References Test Guidance : KDB 447498 D01 General RF Exposure Guidance v06 IEEE C95.3 -2002 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Jun. 10, 2020 Shelly Hsueh / Specialist Approved by : , Date: Jun. 10, 2020 Dylan Chiou / Senior Project Engineer Report No.: SA200407C10 Page No. 5 / 6 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz ; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA200407C10 Page No. 6 / 6 Report Format Version: 6.1.1 2.4 Calculation Result of Maximum Conducted Power CDD Mode: Band Frequency Band (MHz) Max Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) WLAN 2412-2462 26.16 6.01 20 0.328 1.00 5180-5240 27.78 6.01 20 0.476 1.00 5745-5825 25.34 6.01 20 0.271 1.00 Beamforming Mode: Band Frequency Band (MHz) Max Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) WLAN 2412-2462 25.55 6.01 20 0.285 1.00 5180-5240 27.78 6.01 20 0.476 1.00 5745-5825 25.34 6.01 20 0.271 1.00 Note: 1. Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. 2. 2.4GHz: Directional gain = 3dBi + 10log(2) = 6.01dBi 5.0GH…

Text truncated - open the document above for the full version.

Report No.: RF200407C10-1 Page No. 1 / 82 Report Format Version:6.1.2 FCC Test Report Report No.: RF200407C10-1 FCC ID: MSQ-RPAX4W00 Test Model: RP-AX56 Received Date: Apr. 07, 2020 Test Date: May 19, 2020 ~ Jul. 16, 2020 Issued Date: Jul. 22, 2020 Applicant: ASUSTek COMPUTER INC. Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim any endorsement by TAF. Report No.: RF200407C10-1 Page No. 2 / 82 Report Format Version:6.1.2 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 6 2.2 Modification Record .............................................................................................................................. 6 3 General Information ................................................................................................................................... 7 3.1 General Description of EUT .................................................................................................................. 7 3.2 Description of Test Modes ..................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................. 10 3.3 Duty Cycle of Test Signal .................................................................................................................... 12 3.4 Description of Support Units ............................................................................................................... 13 3.4.1 Configuration of System under Test ......................................................................................... 13 3.5 General Description of Applied Standards and References ............................................................... 13 4 Test Types and Results ............................................................................................................................ 14 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 14 4.1.1 Limits of Radiated Emission and Bandedge Measurement ..................................................... 14 4.1.2 Test Instruments ....................................................................................................................... 16 4.1.3 Test Procedures ........................................................................................................................ 17 4.1.4 Deviation from Test Standard ................................................................................................... 17 4.1.5 Test Setup ................................................................................................................................. 18 4.1.6 EUT Operating Conditions ........................................................................................................ 19 4.1.7 Test Results .............................................................................................................................. 20 4.2 Conducted Emission Measurement .................................................................................................... 40 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 40 4.2.2 Test Instruments ....................................................................................................................... 40 4.2.3 Test Procedures ........................................................................................................................ 41 4.2.4 Deviation from Test Standard ................................................................................................... 41 4.2.5 Test …

Text truncated - open the document above for the full version.

FCC ID: MSQ-RPAX4W00 1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: MSQ-RPAX4W00 2 RADIATED EMISSION TEST BELOW 1GHz FCC ID: MSQ-RPAX4W00 3 RADIATED EMISSION TEST ABOVE 1GHz