MSQT00DPadFone X

Important Notices Station (T00DP) (T00D) AT&T_Padfone-X_Safety_Notices.in1 12/14/14 5:27:12 PM Copyright © 2014 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. First Edition AT&T_Padfone-X_Safety_Notices.in2 22/14/14 5:27:12 PM IMPORTANT: All throughout this document, the term “PadFone X device” is used to refer to the two PadFone X devices: PadFone X and PadFone X Station. Safety information PadFone X care • Do not attempt to open your PadFone X device casing. There are no user serviceable parts inside and you might damage sensitive electronic circuits and components. Unauthorized disassembly will void the warranty. • Do notDo not leave your PadFone X device exposed to strong sunlight or excessive heat for a prolonged period. This may damage it. • Do not handle your PadFone X device with wet hands or expose it to moisture or liquids of any kind. Continuous changes from a cold to a warm environment may lead to condensation inside your PadFone X device, resulting in corrosion and possible damage. • If you pack your PadFone X device in your suitcase during travel, beware of damage. Cramming the device into a suitcase may crack the LCD display. Remember to switch off your wireless connection during air travel. • Use your PadFone X device in an environment with ambient temperatures between -10 °C (14 °F) and 35 °C (95 °F). IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the ASUS PadFone X body except on the sides where the I/O ports are located. The battery Your PadFone X device is equipped with a high performance non-detachable Li-Ion battery. Observe the following maintenance guidelines for a longer battery life: • Avoid charging in extremely high or low temperature. The battery performs optimally in an ambient temperature of +5 °C to +35 °C. • Do not remove and replace the battery with a non- approved battery. • Do not remove and immerse the battery in water or any other liquid. AT&T_Padfone-X_Safety_Notices.in3 32/14/14 5:27:13 PM • Never try to open the battery as it contains substances that might be harmful if swallowed or allowed to come into contact with unprotected skin. • Do not remove and short-circuit the battery, as it may overheat and cause a fire. Keep it away from jewellery and other metal objects. • Do not remove and dispose of the battery in fire. It could explode and release harmful substances into the environment. • Do not remove and dispose of the battery with your regular household waste. Take it to a hazardous material collection point. • Do not touch the battery terminals. CAUTION: • Risk of explosion if battery is replaced by an incorrect type. • Dispose of used batteries according to the instructions. The charger • Use only the charger supplied with your PadFone X device. • Never pull the charger cord to disconnect it from the power socket. Pull the charger itself. Cleaning and storing • Your PadFone X device should always be handled with care and protected from dirt, dust and dampness. To avoid scratches, never place your PadFone X device face down. • If cleaning is necessary, turn your PadFone X device off and wipe carefully with a soft, slightly damp (not wet) cloth. Use a cotton swab to clean the camera lens. Allow your PadFone X device to dry completely before switching it on. Never use solvents for cleaning. • If you are not going to use your PadFone X device for some time, fully charge the battery and store your PadFone X device in a dry place away from direct sunlight. Your PadFone X device should be switched off during storage. Recharge every 6 to 12 months. • Never expose your PadFone X device to heat or strong sunlight. • Never expose your PadFone X device to moisture or liquids of any kind. AT&T_Padfone-X_Safety_Notices.in4 42/14/14 5:27:13 PM • Do not place stickers that may block the keypad or affect other components such as the microphone, earpiece, or camera lens. WARNING! Failure to follow these instructions may lead to serious personal injury and possible property damage. Driving safely Never use handheld phones while driving. It is an offence, that while driving, to hold a phone or cradle it in your neck at any point,…

Text truncated - open the document above for the full version.

4F, No. 150, Li-Te Rd., Peitou, Taipei, Taiwan Date: February 27, 2014 Statement We, ASUSTeK Computer Inc, state that there is no other space for putting the label on our device, FCC ID: MSQT00D, except for the space under the back cover of this device. The label will be put above the battery compartment and it is visible to the users as they purchase the product and insert the SIM card. If you have any question regarding the declaration, please don’t hesitate to contact us. Thank you! Sincerely yours,

Report No.: 140123C03 Page 1 of 30 CONSTRUCTION PHOTOS OF EUT Report No.: 140123C03 Page 2 of 30 Report No.: 140123C03 Page 14 of 30 Report No.: 140123C03 Page 15 of 30 Report No.: 140123C03 Page 16 of 30 Report No.: 140123C03 Page 17 of 30 Report No.: 140123C03 Page 18 of 30 Report No.: 140123C03 Page 19 of 30 Report No.: 140123C03 Page 20 of 30 Report No.: 140123C03 Page 21 of 30 Report No.: 140123C03 Page 22 of 30 Report No.: 140123C03 Page 23 of 30 Report No.: 140123C03 Page 24 of 30 Report No.: 140123C03 Page 25 of 30 Report No.: 140123C03 Page 26 of 30 Report No.: 140123C03 Page 27 of 30 Report No.: 140123C03 Page 28 of 30 Report No.: 140123C03 Page 29 of 30 Report No.: 140123C03 Page 30 of 30

US P92L REAR COVER MYLAR 底色: 深灰黑加銀粉(請參考色板) 資訊: Pantone cool gray 8U

A91 AT&T DEVICE LABEL 15100-09020100$ MVDG00 Benny Chen 12/03/2013 MVDG00 Vicki Jan 12/03/2013 1.MATERIAL: 25# WHITE POLYESTER+可打印霧PP 2.ADHESIVE: ACRYLIC 3.COLOR: BACKGROUND------BLACK LETTERS------PANTONE Cool Gray 6C 4.TOLERANCE: +/-0.2mm 5. THE MATERIAL MUST BE APPROVED BY UL, CSA (由wks打印內容) * IMEI number and barcode (barcode type: code 128,barcode height is 1/4") * SKU number and barcode (barcode type: code 128,barcode height is 1/4") * SSN number and barcode (barcode type: code 128,barcode height is 1/4") * MFG date Model：T00D Input : +5V 2A, 10W FCC ID：MSQT00D Made in China 41+/-0.15 mm 32.46 mm 77.12 mm 94.8+/-0.15 mm R0.5 mm(x4) IMEI: xxxxxxxxxxxxxxx SKU: xxxxxxxxxxxxxx SSN: xxxxxxxxxxxxMFG: YYYYMMDD H/W:xxxxx

FCC ID: MSQT00D Back cover of Station: Pad Phone The label will be put above the battery compartment. Pad Phone Label Location Label Location

Report No.: 140123C03 Page 3 of 30 Report No.: 140123C03 Page 4 of 30 Report No.: 140123C03 Page 5 of 30 Report No.: 140123C03 Page 6 of 30 Report No.: 140123C03 Page 7 of 30 Report No.: 140123C03 Page 8 of 30 Report No.: 140123C03 Page 9 of 30 Report No.: 140123C03 Page 10 of 30 Report No.: 140123C03 Page 11 of 30 Report No.: 140123C03 Page 12 of 30 Report No.: 140123C03 Page 13 of 30

FCC SAR Test Report Report Format Version 5.0.0 Issued Date : Feb. 27, 2014 Report No. : SA131213C05 Appendix C. Calibration Certificate for Probe and Dipole The SPEAG calibration certificates are shown as follows.

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 78 Report No. : SA131213C05 Issued Date : Feb. 27, 2014 FCC SAR Test Report Report No. : SA131213C05 Applicant : ASUSTek COMPUTER INC. Address : 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN Product : PadFone X FCC ID : MSQT00D Brand : ASUS Model No. : T00D Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1992 / IEEE 1528:2003 IEEE 1528a-2005 / KDB 865664 D01 v01r03 / KDB 248227 D01 v01r02 KDB 447498 D01 v05r02 / KDB 616217 D04 v01r01 / KDB 648474 D04 v01r02 KDB 941225 D01 v02 / KDB 941225 D02 v02r02 / KDB 941225 D03 v01 KDB 941225 D05 v02r03 / KDB 941225 D06 v01r01 Sample Received Date : Dec. 13, 2013 Date of Testing : Jan. 03, 2014 ~ Feb. 20, 2014 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Evonne Liu / Specialist Approved By : Roy Wu / Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 78 Report No. : SA131213C05 Issued Date : Feb. 27, 2014 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 6 3. SAR Measurement System ................................................................................................................................................... 7 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 7 3.2 SPEAG DASY System ................................................................................................................................................. 7 3.2.1 Robot.................................................................................................................................................................. 8 3.2.2 Probes ................................................................................................................................................................ 9 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 9 3.2.4 Phantoms ......................................................................................................................................................... 10 3.2.5 Device Holder ................................................................................................................................................... 11 3.2.6 System Validation Dipoles ................................................................................................................................ 11 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 12 3.3 SAR System Verification ............................................................................................................................................ 15 3.4 SAR Measurement Procedure ................................................................................................................................... 16 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 16 3.4.2 Volume Scan Procedure................................................................................................................................... 16 3.4.3 Power Drift Monitoring ...................................................................................................................................... 17 3.4.4 Spatial Peak SAR Evaluation .............................................................…

Text truncated - open the document above for the full version.

Report No.: RF131213C05-3 1 of 81 Report Format Version 5.2.0 FCC TEST REPORT (BLUETOOTH) REPORT NO.: RF131213C05-3 MODEL NO.: T00D FCC ID: MSQT00D RECEIVED: Dec. 13, 2013 TESTED: Dec. 27, 2013 ~ Feb. 20, 2014 ISSUED: Feb. 27, 2014 APPLICANT: ASUSTek COMPUTER INC. ADDRESS: 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF131213C05-3 2 of 81 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ..............................................................................................................5 1. CERTIFICATION ..................................................................................................................................6 2. SUMMARY OF TEST RESULTS .........................................................................................................7 2.1 MEASUREMENT UNCERTAINTY...............................................................................................8 3. GENERAL INFORMATION ..................................................................................................................9 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................9 3.2 DESCRIPTION OF TEST MODES ............................................................................................ 11 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .............................. 12 3.3 DESCRIPTION OF SUPPORT UNITS ..................................................................................... 16 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................... 16 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 16 4. TEST TYPES AND RESULTS (FOR BLUETOOTH EDR) ............................................................... 17 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 17 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................... 17 4.1.2 TEST INSTRUMENTS ................................................................................................. 18 4.1.3 TEST PROCEDURES ................................................................................................. 19 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................... 19 4.1.5 TEST SETUP ............................................................................................................... 20 4.1.6 EUT OPERATING CONDITIONS ................................................................................ 21 4.1.7 TEST RESULTS........................................................................................................... 22 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 32 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 32 4.2.2 TEST INSTRUMENTS ................................................................................................. 32 4.2.3 TEST PROCEDURES ................................................................................................. 33 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................... 33 4.2.5 TEST SETUP ............................................................................................................... 34 4.2.6 EUT OPERATING CONDITIONS ................................................................................ 34 4.2.7 TEST RESULTS........................................................................................................... 35 4.3 NUMBER OF HOPPING FREQUENCY USED ........................................................................ 39 4.3.1 LIMIT OF HOPPING FREQUENCY USED ................................................................. 39 4.3.2 TEST SETUP ............................................................................................................... 39 4.3.3 TEST INSTRUMENTS ................................................................................................. 39 4.3.4 TEST PROCEDURE .........................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF131213C05-4 1 of 95 Report Format Version 5.2.0 FCC TEST REPORT (15.247) REPORT NO.: RF131213C05-4 MODEL NO.: T00D FCC ID: MSQT00D RECEIVED: Dec. 13, 2013 TESTED: Dec. 23, 2013 ~ Feb. 20, 2014 ISSUED: Feb. 27, 2014 APPLICANT: ASUSTek COMPUTER INC. ADDRESS: 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF131213C05-4 2 of 95 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ..............................................................................................................5 1. CERTIFICATION ..................................................................................................................................6 2. SUMMARY OF TEST RESULTS .........................................................................................................7 2.1 MEASUREMENT UNCERTAINTY...............................................................................................7 3. GENERAL INFORMATION ..................................................................................................................8 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................8 3.2 DESCRIPTION OF TEST MODES ........................................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................... 11 3.3 DESCRIPTION OF SUPPORT UNITS ..................................................................................... 15 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................... 15 3.4 DUTY CYCLE TEST SIGNAL ................................................................................................... 16 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 18 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ....................................................................... 19 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 19 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................... 19 4.1.2 TEST INSTRUMENTS ................................................................................................. 20 4.1.3 TEST PROCEDURES ................................................................................................. 21 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................... 21 4.1.5 TEST SETUP ............................................................................................................... 22 4.1.6 EUT OPERATING CONDITIONS ................................................................................ 23 4.1.7 TEST RESULTS........................................................................................................... 24 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 40 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 40 4.2.2 TEST INSTRUMENTS ................................................................................................. 40 4.2.3 TEST PROCEDURES ................................................................................................. 41 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................... 41 4.2.5 TEST SETUP ............................................................................................................... 42 4.2.6 EUT OPERATING CONDITIONS ................................................................................ 42 4.2.7 TEST RESULTS........................................................................................................... 43 4.3 6dB BANDWIDTH MEASUREMENT ....................................................................................... 47 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ........................................................ 47 4.3.2 TEST SETUP ............................................................................................................... 47 4.3.3 TEST INSTRUMENTS ...........................................................................…

Text truncated - open the document above for the full version.

FCC SAR Test Report Report Format Version 5.0.0 Issued Date : Feb. 27, 2014 Report No. : SA131213C05 Appendix D. Photographs of EUT and Setup FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA131213C05 <Photographs of EUT> Handset - Front View Handset – Rear View PadFone Station – Fornt View PadFone Station – Rear View Handset + PadFone Station – Rear View FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA131213C05 <Antenna Location> The separation distance for antenna to edge: Antenna To Top Side (mm) To Bottom Side (mm) To Left Side (mm) To Right Side (mm) WWAN 130.3 0 5 5 WLAN 0 127 0 61.7 The separation distance for antenna to edge: Antenna To Top Side (mm) To Bottom Side (mm) To Left Side (mm) To Right Side (mm) WWAN 6.49 154.48 174.51 18.45 WLAN / BT 5.25 153.12 91.5 147.2 Note: Since the technical document related to the design of proximity sensor and power reduction is confidential, the detail about proximity sensor does not be described in this SAR report. Please refer to the technical documents as “Proximity Sensor Technical Description” for the details. Bottom Side Top Side Left Side Right Side WWAN Antenna <Handset + Tablet Rear View> WWAN Antenna <Handset Rear View> <PadFone Station> <Handset> Left Side Right Side Top Side Bottom Side WLAN / BT Antenna WLAN/BT Antenna Bottom Side P-Sensor Coverage FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA131213C05 <Photographs of SAR Setup> Right Cheek (Handset, Head Mode) Right Tilted (Handset, Head Mode) Left Cheek (Handset, Head Mode) Left Tilted (Handset, Head Mode) FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA131213C05 Front Face of EUT with 1.0 cm Gap (Handset, Body Mode) Rear Face of EUT with 1.0 cm Gap (Handset, Body Mode) Left Side of EUT with 1.0 cm Gap (Handset, Body Mode) Right Side of EUT with 1.0 cm Gap (Handset, Body Mode) Top Side of EUT with 1.0 cm Gap (Handset, Body Mode) Bottom Side of EUT with 1.0 cm Gap (Handset, Body Mode) FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA131213C05 Rear Face of EUT with 0 cm Gap (Tablet, Body Mode for WWAN) Rear Face of EUT with 1.1 cm Gap (Tablet, Body Mode for WWAN) Top Side of EUT with 0 cm Gap (Tablet, Body Mode) Top Side of EUT with 0.8 cm Gap (Tablet, Body Mode) Right Side of EUT with 0 cm Gap (Tablet, Body Mode) Rear Face of EUT with 0 cm Gap (Tablet, Body Mode for WLAN & BT)

Report No.: RF131213C05 1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST MODE A (For Bluetooth LE 4.0) Report No.: RF131213C05 2 CONDUCTED EMISSION TEST MODE A (For Bluetooth / WLAN 2.4GHz / WLAN 5GHz) Report No.: RF131213C05 3 CONDUCTED EMISSION TEST MODE B (For Bluetooth / WLAN 2.4GHz) Report No.: RF131213C05 4 RADIATED EMISSION TEST MODE A (For Bluetooth / Bluetooth LE 4.0 / WLAN 2.4GHz / WLAN 5Hz) (For 5745~5825MHz) Report No.: RF131213C05 5 RADIATED EMISSION TEST MODE B (For Bluetooth / Bluetooth LE 4.0 / WLAN 5Hz) Report No.: RF131213C05 6 RADIATED EMISSION TEST MODE C (For Bluetooth / WLAN 2.4GHz / WLAN 5Hz) (For 5180~5700MHz) Report No.: RF131213C05 7 RADIATED EMISSION TEST MODE D (For WLAN 5Hz) (For 5180~5700MHz) Report No.: RF131213C05 8 RADIATED EMISSION TEST MODE A (For WLAN 5Hz) (For 5180~5700MHz) Report N…

Text truncated - open the document above for the full version.