MSQW1NWM3B2100Notebook PC

Copyright Information No part of this manual, including the products and software described in it, may be reproduced, transmitted, tran- scribed, stored in a retrieval system, or translated into any language in any form or by any means, except documen- tation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COM- PUTER INC. (“ASUS”). ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MER- CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIREC- TORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSI- NESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFOR- MATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LI- ABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved. Limitation of Liability Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property; or any other actual and direct damages resulted from omission or failure of performing legal duties under this Warranty Statement, up to the listed contract price of each product. ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringe- ment under this Warranty Statement. This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible. UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RE- SELLER IS INFORMED OF THEIR POSSIBILITY. 1 Product Name:Notebook PC Hardware Manual Revision:1 E1541 Release Date:January 2004 Notebook PC Hardware User’s Manual 2 Safety Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that inter- ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the Federal Register, National Archives and Records Administration, U.S. Government Printing Office. Power Safety Requirement Products with electrical current ratings up to 6A and weighing more than 3Kg must use approved power cords greater than or equal to: H05VV-F, 3G, 0.75mm 2 or H05VV-F, 2G, 0.75mm 2 . Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This Class B digital apparatus complies with Canadian ICES-003. (Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.) For use with AC Adaptor Model (Pour Utiliser Avec Modele): ADP-65DB (65W) WARNING! The use of a shielded-type power cord is required in order to meet FCC emission limits and to prevent interference to the nearby radio and television recep- tion. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for complia…

Text truncated - open the document above for the full version.

55 44 33 22 11 D D C C B B A A PCI DDR SO-DIMM SUPER I/O PAGE 19 PAGE 31,32,33 HDD FWH PAGE 16,17,18 GIGA LAN3COM LPC PAGE 29 1.5V PAGE 27 2.5V CD ROM MINI-PCI 1 CRT PAGE 39 PAGE 24,25,26 PAGE 15 MDC PAGE 2,3 ATI M10 PAGE 24 PAGE 15 1.8V USB 2.0 PAGE 23 PAGE 14 SIR 1.2VS PAGE 42 AUDIO CODEC ODEM PAGE 22 PAGE 11,12,13 VCCP PAGE 41 PAGE 22 PAGE 8,9,10 CPU VCORE R5C593 PAGE 41 PAGE 7 PAGE 39 AUDIO DJ KEY PAGE 5,6 POWER PAGE 38 PAGE 42 3V , 5V , 12V LVDS POWER SEQUENCE PSB PAGE 41 PS2 CON DDR PAGE 21 PAGE 41 PAGE 37 1.25VS CLOCKGENERATOR HUB CPU CSP64 PAGE 40 PAGE 4 PAGE 20 INSTANT KEY MCH-M PAGE 28 ICH4-M TV OUT AGP BANIAS PAGE 19 KBC 38857 FAN + SENSOR CIR PAGE 22 MINI-PCI 2 PAGE 30 PAGE 15 PCMCIA 1394 CARD READER PAGE 15PAGE 14 Custom Tuesday, September 30, 2003 ASUSTeK COMPUTER INC BLOCK DIAGRAM 2.0 W1 S 00N,W1B00N Jerry Mou 150 P4PE-X R2.00 Size Project Name Rev Date: Sheet of Title : Engineer:

Report No.: 042L056FI Page : 1 of 9 Version:1.0 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo Report No.: 042L056FI Page : 2 of 9 Version:1.0 (3) EUT Photo (4) EUT Photo Report No.: 042L056FI Page : 3 of 9 Version:1.0 (5) EUT Photo (6) EUT Photo Report No.: 042L056FI Page : 4 of 9 Version:1.0 (7) EUT Photo (8) EUT Photo Report No.: 042L056FI Page : 5 of 9 Version:1.0 (9) EUT Photo (10) EUT Photo

ASUSTeK COMPUTER INC. FCC ID.: MSQW1NWM3B2100 4FL., No. 150, Li-Te Rd., Peitou, Taipei, Taiwan, R.O.C. Tel: 886 2 2894-3447 FCC ID AND DoC Label The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. Notebook P.C. ASUS Model No.: W1S00N, W1B00N TESTED TO COMPLY WITH FCC STANDARDS FOR HOME OR OFFICE USE S/N: Made in Taiwan Notebook P.C. Model No.: W1S00N, W1B00N F F C C C C I I D D : : M M S S Q Q W W 1 1 N N W W M M 3 3 B B 2 2 1 1 0 0 0 0 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan

ASUSTeK COMPUTER INC. FCC ID.: MSQW1NWM3B2100 4FL., No. 150, Li-Te Rd., Peitou, Taipei, Taiwan, R.O.C. Tel: 886 2 2894-3447 FCC ID AND DoC Label The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. Notebook P.C. ASUS Model No.: W1S00N, W1B00N TESTED TO COMPLY WITH FCC STANDARDS FOR HOME OR OFFICE USE S/N: Made in Taiwan Notebook P.C. Model No.: W1S00N, W1B00N F F C C C C I I D D : : M M S S Q Q W W 1 1 N N W W M M 3 3 B B 2 2 1 1 0 0 0 0 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan

Report No.: 042L056FI Page : 6 of 9 Version:1.0 (11) EUT Photo (12) EUT Photo Report No.: 042L056FI Page : 7 of 9 Version:1.0 (13) EUT Photo (14) EUT Photo Report No.: 042L056FI Page : 8 of 9 Version:1.0 (15) EUT Photo (16) EUT Photo Report No.: 042L056FI Page : 9 of 9 Version:1.0 (17) EUT Photo

Report No. 042L056FI Page: 5 of 42 Version:1.0 1.2. Operational Description EUT is a Notebook P.C. with 11 channels. This device provided four kinds of transmitting speed 1, 2, 5.5 and 11Mbps. The device of RF carrier is DQPSK, DBPSK and CCK (IEEE 802.11b) The device adapts direct sequence spread spectrum modulation. The antenna was Connector provides diversity function to improve the receiving function. This Notebook P.C., compliant with IEEE 802.11b, is a high-efficiency Wireless LAN adapter. It allows your computer to connect to a wireless network and to share resources, such as files or printers without being bound to the network wires. Operation in 2.4GHz Direst Sequence Spread Spectrum (DSSS) radio transmission, the Notebook P.C. Wired Equivalent Protection (WEP) algorithm is used. In addition, its standard compliance ensures that it can communicate with any IEEE 802.11b network. Test Mode: Mode 1: Transmitter 802.11b

Report No. 042L056FI Page: 1 of 42 Version:1.0 Test Report Product Name : Notebook P.C. Model No. : W1S00N, W1B00N FCC ID : MSQW1NWM3B2100 Applicant : ASUSTeK COMPUTER INC. Address : 4FL., No. 150, Li-Te Rd., Peitou, Taipei, Taiwan, R.O.C. Date of Receipt : Feb. 05. 2004 Date of Test : Feb. 12. 2004 Report No. : 042L056FI The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Report No. 042L056FI Page: 2 of 42 Version:1.0 Test Report Certification Test Date: Feb. 12. 2004 Report No. : 042L056FI Test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Product Name : Notebook P.C. Applicant : ASUSTeK COMPUTER INC. Address : 4FL., No. 150, Li-Te Rd., Peitou, Taipei, Taiwan, R.O.C. Manufacturer : ASUSTeK COMPUTER INC. Model No. : W1S00N, W1B00N Rated Voltage : AC 120V/60Hz Trade Name : ASUS Measurement Standard : FCC Part 15 Subpart C Paragraph 15.247 Measurement Procedure : ANSI C63.4: 2001 Test Result : Complied Documented By : ( Gina Chen ) Tested By : ( Geddy Jerg ) Approved By : ( Gene Chang ) Accredited by NIST (NVLAP) NVLAP Lab Code: 200533-0 Report No. 042L056FI Page: 3 of 42 Version:1.0 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .....................................................................................................4 1.1. EUT Description............................................................................................................................4 1.2. Operational Description ................................................................................................................5 1.3. Tested System Datails....................................................................................................................6 1.4. Configuration of tested System .....................................................................................................7 1.5. EUT Exercise Software .................................................................................................................7 1.6. Test Facility ...................................................................................................................................8 2. CONDUCTED EMISSION ........................................................................................................9 2.1. Test Equipment..............................................................................................................................9 2.2. Test Setup ......................................................................................................................................9 2.3. Limits ..........................................................................................................................................10 2.4. Test Procedure .............................................................................................................................10 2.5. Test Result of Conducted Emission.............................................................................................11 3. PEAK POWER OUTPUT ........................................................................................................17 3.1. Test Equipment............................................................................................................................17 3.2. Test Setup ....................................................................................................................................17 3.3. Limits ..........................................................................................................................................17 3.4. Test Result of Peak Power Output...............................................................................................18 4. RADIATED EMISSION ...........................................................................................................19 4.1. Test Equipment............................................................................................................................19 4.2. Test Setup ....................................................................................................................................19 4.3. Limits ..........................................................................................................................................20 4.4. Test Procedure .............................................................................................................................21 4.5. Test Result of Radiated Emission................................................................................................22 5. BAND EDGE .............................................................................................................................28 5.1. Test Equipment............................................................................................................................28 5.2. Test Setup ....................................................................................................................................28 5.3. 29 5.4. Limits ..........................................................................................................................................29 5.5. Test Procedure .............................................................................................................................29 5.6. Test Result of Band Edge ............................................................................................................30 6. OCCUPIED BANDWIDTH .....................................................................................................32 6.1.…

Text truncated - open the document above for the full version.

Report No.: 042L056FI Page : 1 of 3 Version:1.0 Attachment 1: EUT Test Setup Photographs Front View of Conducted Test Back View of Conducted Test Report No.: 042L056FI Page : 2 of 3 Version:1.0 Front View of Radiated Test Back View of Radiated Test Report No.: 042L056FI Page : 3 of 3 Version:1.0 Front View of High Frequency Radiated Test