MSQZ00DASUS Phone

Important Notices Copyright © 2015 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE First Edition January 2015 LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Safety information ASUS Phone care • Do not leave your ASUS Phone exposed to strong sunlight or excessive heat for a prolonged period. This may damage it. • Do not handle your ASUS Phone with wet hands or expose it to moisture or liquids of any kind. Continuous changes from a cold to a warm environment may lead to condensation inside your ASUS Phone, resulting in corrosion and possible damage. • If you pack your ASUS Phone in your suitcase during travel, beware of damage. Cramming the device into a suitcase may crack the LCD display. Remember to switch off your wireless connection during air travel. • Use your ASUS Phone in an environment with ambient temperatures between -10 °C (14 °F) and 35 °C (95 °F). IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the ASUS Phone body except on the sides where the I/O ports are located. The battery Your ASUS Phone is equipped with a high performance non-detachable Li-Ion battery. Observe the following maintenance guidelines for a longer battery life: • Avoid charging in extremely high or low temperature. The battery performs optimally in an ambient temperature of +5 °C to +35 °C. • Do not remove and replace the battery with a non-approved battery. • Do not remove and immerse the battery in water or any other liquid. • Never try to open the battery as it contains substances that might be harmful if swallowed or allowed to come into contact with unprotected skin. • Do not remove and short-circuit the battery, as it may overheat and cause a fire. Keep it away from jewellery and other metal objects. • Do not remove and dispose of the battery in fire. It could explode and release harmful substances into the environment. • Do not remove and dispose of the battery with your regular household waste. Take it to a hazardous material collection point. • Do not touch the battery terminals. CAUTION: • Risk of explosion if battery is replaced by an incorrect type. • Dispose of used batteries according to the instructions. The charger • Use only the charger supplied with your ASUS Phone. • Never pull the charger cord to disconnect it from the power socket. Pull the charger itself. Cleaning and storing • Your ASUS Phone should always be handled with care and protected from dirt, dust and dampness. To avoid scratches, never place your ASUS Phone face down. • If cleaning is necessary, turn your ASUS Phone off and wipe carefully with a soft, slightly damp (not wet) cloth. Use a cotton swab to clean the camera lens. Allow your ASUS Phone to dry completely before switching it on. Never use solvents for cleaning. • If you are not going to use your ASUS Phone for some time, fully charge the battery and store your ASUS Phone in a dry place away from direct sunlight. Your ASUS Phone should be switched off during storage. Recharge every 6 to 12 months. • Never expose your ASUS Phone to heat or strong sunlight. • Never expose your ASUS Phone to moisture or liquids of any kind. • Do not place stickers that may block the keypad or affect other components such as the microphone, earpiece, or camera lens. WARNING! Failure to follow these instructions may lead to serious personal injury and possible property damage. Driving safely Never use handheld phones while driving. It is an offence, that while driving, to hold a phone or cradle it in your neck at any point, during the setup, making or taking of a phone call, text message or any other data related mobile communication. Use of fully installed car kits are still permitted, as are the use of alternate handsfree accessories. In the interest of safety, we would recommend the use of a cradle while using any form of handsfree accessory. While driving, we recommend that you use voicemail wherever possible, and that you listen to your messages when you are not in the car. If you must make a handsfree call when driving, keep it brief. Do not place objects, including both installed or portable wireless equipment, in the area over the airbag or in the airbag deployment area. An airbag inflates with gr…

Text truncated - open the document above for the full version.

User Guide E9995 E9995 First Edition January 2015 Model: Z00D (ZE500CL) Copyright © 2015 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Thank you for purchasing this ASUS product! Before you start, ensure that you have read all the safety information and operating instructions in this User Guide to prevent injury or damage to your device. NOTE: For the latest updates and more detailed information, please visit www. asus.com. Touch screen display Receiver Power key Touch keys Getting started with your ASUS Phone Front features Front camera Sensor Side features Audio jack Micro USB port Power key Groove NOTE: Pry open the rear cover from the groove. Microphone Rear features Flash Volume key Rear camera Rear cover NOTES: • Remove the rear cover to display the micro SIM and microSD card slots. • The micro SIM card slot supports WCDMA, DC-HSPA, GSM/EDGE, and FDD-LTE network bands. • The microSD card slot supports microSD and microSDHC card formats. Speaker Charging your ASUS Phone After installing your micro SIM card, we strongly recommend that you charge your device fully before powering it ON. To charge your ASUS Phone: 1. Connect the USB connector into the power adapter’s USB port. 2. Connect the other end of the micro USB cable to your ASUS Phone. 3. Plug the power adapter into a wall socket. 3 1 2 IMPORTANT! • When using your ASUS Phone while it is plugged to a power outlet, the grounded power outlet must be near to the unit and easily accessible. • When charging your ASUS Phone through your computer, ensure that you plug the micro USB cable to your computer’s USB 2.0 / USB 3.0 port. • Avoid charging your ASUS Phone in an environment with ambient temperature of above 35 o C (95 o F). NOTES: • Use only the power adapter that came with your device. Using a different power adapter may damage your device. • Using the bundled power adapter and ASUS Phone signal cable to connect your ASUS Phone to a power outlet is the best way to charge your ASUS Phone. • The input voltage range between the wall outlet and this adapter is AC 100V - 240V. The output voltage of the micro USB cable is DC 5.2V, 1.35A. IMPORTANT: The first time you power on your ASUS Phone, you will see the Welcome screen. Touch the menu to select your preferred language then touch Next Step. Follow the onscreen instructions to set up your ASUS Phone. Turning your ASUS Phone on or off Press the power key at the top of your ASUS Phone to power the device on or to power it off. Power key 3. Insert the micro SIM card into the micro SIM slot. 1. Locate the groove on the bottom-right corner of your ASUS Phone. Installing a micro SIM card To install a micro SIM card: 2. Pry the cover loose and then pull the rear cover off. 4. Replace the rear cover. 5. Press down the rear cover on all sides to secure it in place. IMPORTANT: Use only a micro SIM card on your ASUS Phone. A trimmed SIM card may not properly fit into and may not be detected by your ASUS Phone. NOTE: All specifications are subject to change without notice and may vary by country and region. CAUTION: Do not use sharp tools or solvent on your device to avoid scratches on it. Installing a microSD card To install a microSD card: 3. Insert the microSD card into the microSD card slot. 1. Locate the groove on the bottom-right corner of your ASUS Phone. 2. Pry the cover loose and then pull the rear cover off. CAUTION: Do not use sharp tools or solvent on your device to avoid scratches on it. 4. Replace the rear cover. 5. Press down the rear cover on all sides to secure it in place. Using GPS (Global Positioning System) on your ASUS Phone To use the GPS positioning feature on your ASUS Phone: • Ensure that your device is connected to the Internet before using Google Map or any GPS-enabled apps. • For first-time use of a GPS-enabled app on your device, ensure that you are outdoors to get the best positioning data. • When using a GPS-enabled app on your device inside a vehicle, the metallic component of the car window and other electronic devices might affect the GPS performance. CE RF Exposure Compliance This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general public to elec…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 January 23, 2015 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, ASUSTeK Computer Inc, hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): (ASUS Phone, Z00D) FCC ID: MSQZ00D Sincerely, _____________________ Daniel Lee / Vice President Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Tel: +886 3 318 3232 #1857

Page 1 of 19 Report No.: 141216C28 CONSTRUCTION PHOTOS OF EUT Page 2 of 19 Report No.: 141216C28 Page 3 of 19 Report No.: 141216C28 Page 4 of 19 Report No.: 141216C28 Page 5 of 19 Report No.: 141216C28 Page 6 of 19 Report No.: 141216C28 Page 7 of 19 Report No.: 141216C28 Page 8 of 19 Report No.: 141216C28

Page 9 of 19 Report No.: 141216C28 Page 10 of 19 Report No.: 141216C28 Page 11 of 19 Report No.: 141216C28 Page 12 of 19 Report No.: 141216C28 Page 13 of 19 Report No.: 141216C28 Page 14 of 19 Report No.: 141216C28 Page 15 of 19 Report No.: 141216C28 Page 16 of 19 Report No.: 141216C28 Page 17 of 19 Report No.: 141216C28 Page 18 of 19 Report No.: 141216C28 Page 19 of 19 Report No.: 141216C28

Report No.: RF141216C28-5 1 of 68 Report Format Version 5.1.0 FCC TEST REPORT (BLUETOOTH) REPORT NO.: RF141216C28-5 MODEL NO.: Z00D FCC ID: MSQZ00D RECEIVED: Dec. 16, 2014 TESTED: Dec. 30, 2014 ~ Jan. 08, 2015 ISSUED: Jan. 16, 2015 APPLICANT: ASUSTek COMPUTER INC. ADDRESS: 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF141216C28-5 2 of 68 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ..............................................................................................................5 1. CERTIFICATION ..................................................................................................................................6 2. SUMMARY OF TEST RESULTS .........................................................................................................7 2.1 MEASUREMENT UNCERTAINTY...............................................................................................8 3. GENERAL INFORMATION ..................................................................................................................9 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................9 3.2 DESCRIPTION OF TEST MODES ............................................................................................ 11 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .............................. 12 3.3 DESCRIPTION OF SUPPORT UNITS ..................................................................................... 16 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................... 16 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 17 4. TEST TYPES AND RESULTS (FOR BLUETOOTH EDR) ............................................................... 18 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 18 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................... 18 4.1.2 TEST INSTRUMENTS ................................................................................................. 19 4.1.3 TEST PROCEDURES ................................................................................................. 20 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................... 20 4.1.5 TEST SETUP ............................................................................................................... 21 4.1.6 EUT OPERATING CONDITIONS ................................................................................ 22 4.1.7 TEST RESULTS........................................................................................................... 23 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 27 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 27 4.2.2 TEST INSTRUMENTS ................................................................................................. 27 4.2.3 TEST PROCEDURES ................................................................................................. 28 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................... 28 4.2.5 TEST SETUP ............................................................................................................... 29 4.2.6 EUT OPERATING CONDITIONS ................................................................................ 29 4.2.7 TEST RESULTS........................................................................................................... 30 4.3 NUMBER OF HOPPING FREQUENCY USED ........................................................................ 32 4.3.1 LIMIT OF HOPPING FREQUENCY USED ................................................................. 32 4.3.2 TEST SETUP ............................................................................................................... 32 4.3.3 TEST INSTRUMENTS ................................................................................................. 32 4.3.4 TEST PROCEDURE .......................................................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST (For WLAN 2.4GHz & Bluetooth) 2 RADIATED EMISSION TEST (For WLAN 2.4GHz & Bluetooth) 3 (WWAN) (PART 22) RADIATED EMISSION TEST 4 ERP POWER TEST 5 (PART 24) RADIATED EMISSION TEST 6 EIRP POWER TEST 7 (PART 27) RADIATED EMISSION TEST 8 ERP POWER TEST 9 EIRP POWER TEST