N8WSUPERCFL

User Manual: Please read this user manual carefully before installation.Keep user manual for fature reference. Technical Data: Model Rated Voltage Input Frequency Rated Wattage Rated Current Lamp Cap EU-13W 120V 60Hz 13W 210mA E26 Treatment of the lamp - Please don't drop the lamp or push against it. - Please don't disassemble the lamp, don't make alterations.2 Installation - Can't be used in dimming circuit. - Don't install inside a recessed area in the wall. - Don't use lids without ventilation openings. - Don't cover with a glass bowl. - For lamps with a weight significantly higher than that of the lamps for which they are a replacement, attention should be drawn to the fact that the increased weitht may reduce the mechanical stability of certain luminaire. Electrical connection - Use only in indoor areas at an ambient temperature 25°C. - Don't use as emergency lighting. - To avoid electrical shock, don't install in damp or wet locations. Remarks - Don't touch the lamp directly with your hand or face when it is in use to avoid burns. - If the lamp is damaged, replace it by a new one and don't try to repair it in order to avoid hazards. - If this lamp should be replaced by a heavier one, please take care that the mechanical stability of the luminaire could be impaired by the increased weight. - Energy saving lamps containing a small amount of quicksilver/mercury (ca. 5 mg). Nevertheless the toxicity of this small amount requires a disposal as hazarduse waste. - In the case a lamp breaks, there is no direct risk for the healthiness, but don’t touch powdery substances, improve air ventilation. Keep children away. NOTE This device complies with part 18 of the FCC Rules. 1, Before commissioning this oven please read this instruction manual and keep it carefully. 2, There must be more than 30cm high space necessary above the top surface of oven. 3, Do not repair the oven yourself, please consult an authorized expert. 4, The contents of feeding bottles and bay food jars are to be stirred or shaken and the temperature is to be checked before consumption, in order to avoid burns. 5, Check the oven and the cable regularly for damage. If there is any kind of damage, the oven should not be used. „ Do not attempt to operate this oven with the door open since open- door operation can result in harmfulexposure to microwave energy. It is important not to defeat or tamper with the safety interlocks. „ Carefully clean door seala and sealing surfaces. „ Do not operate the oven if it is damaged. It is particularly important that the oven door close properly and that there is no damage to the : (1) door(bent). (2) hinges and latches( broken or loosened). (3) door seals and sealing surfaces. „ Utensils sould be checked to ensure that they are suitable for use in microwave ovens. „ When heating food in plastic or paper containers, check the oven frequently due to the possibility of ignition. „ Microwave heating of beverages can result in delayed eruptive boiling, therefore care has to be taken when handling the container. „ If smoke is observed, switch off or unplug the appliance and keep the door closed in order to stifle any flames. „ Egg in their shell and whole hard- bolled eggs shall not be heated in microwave ovens since they may explode. „ If the door or door seals are damaged. The oven must not be operated until it has been repaired by a trained person. „ Liquids or other foods must not be heated in sealed containers since they are liable to explode. Warning: 1, It is hazardous for anyone other than a trained person to carry out any service or repair operation, which involves the removal of any cover which gives protection against exposure to microwave energy. 2, Only allow children to use the oven without supervision when adequate instructions have been given so that the children is able to use the oven in a safe way and understands the hazards of improper use. 3, If the supply cord is damaged, it must be replaced by the manufacture of its service agent or a similarly qualified person in order to avoid a hazard. 4, This product will make disturbance in AV product, if any disturbance is occurred, use different electrical source jack to supply electricity or use low power or away from them. Note: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZATED MODIFICATIONS TO THIS EQUIPMENT .SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Circuit Block Diagram Rectification Circuit Filter Circuit Oscillating Circuit Limited DC circuit component Limited circuit component L A M P L N FUSE 120V 60Hz Input

External Photos

ID Label Label FCC ID: N8WSUPER

ID Label/Location Label Location Information Specifications: Text is Black or white in color and is left justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Label Location

Internal Photos

Circuit Description Fuse: When input is shorted, it performs input shorted protect function. L1C1: Work together with to performs EMI function. D1D2D3D4: Performs rectification function. Q1  Q4  RK: Performs Oscillating function, let low frequency switch high frequency. L2C7: When switching power, the L2 and C7 take place series resonance startup the lamp, then L1 restricting current.

Circuit Diagram R2 R4 R3 R1 PTC Q1 Q2 RK-b RK-a RK-c L1 L2 C2 C4 C3 C6 C5 D5 D6 N L 120V AC 60Hz F. LAMP D1 D2 D3 D4 C7 RFS J4 J3 J1 J2 C1

Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of Bay Area Compliance Lab Corp. (ShenZhen). This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the US Government. FCC PART 18 EMI MEASUREMENT AND TEST REPORT For Super Trend Lighting Limited Rm 302-306,Hewlett Centre,54 hoi Yuen Road,Kwun Tong,Kln,H.K. FCC ID: N8WSUPER January 12, 2006 This Report Concerns: Original Report Equipment Type: CFL Test Engineer: Charmi Peng Report Number: RSZ06011181 Test Date: January 12, 2006 Reviewed By: Chris Zeng Prepared By: Bay Area Compliance Lab Corp. (ShenZhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone, ShenZhen, Guangdong 518038, P.R.China Tel: +86-755-33320018 Fax: +86-755-33320008 Super Trend Lighting Limited FCC ID: N8WSUPER Report # 621779.DOC Page 2 of 11 FCC Part 18 Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................................................3 OBJECTIVE...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................3 TEST METHODOLOGY..................................................................................................................................................3 TEST FACILITY.............................................................................................................................................................3 EXTERNAL I/O CABLE..................................................................................................................................................5 SYSTEM TEST CONFIGURATION ..........................................................................................................................6 JUSTIFICATION.............................................................................................................................................................6 EQUIPMENT MODIFICATIONS.......................................................................................................................................6 CONFIGURATION OF TEST SETUP.................................................................................................................................6 BLOCK DIAGRAM OF TEST SETUP................................................................................................................................6 CONDUCTED EMISSION...........................................................................................................................................7 MEASUREMENT UNCERTAINTY....................................................................................................................................7 EUT SETUP..................................................................................................................................................................7 EMI TEST RECEIVER SETUP.........................................................................................................................................8 TEST EQUIPMENT LIST AND DETAILS...........................................................................................................................8 TEST PROCEDURE........................................................................................................................................................8 TEST RESULTS SUMMARY............................................................................................................................................8 TEST DATA..................................................................................................................................................................9 PLOT(S) OF TEST DATA................................................................................................................................................9 Super Trend Lighting Limited FCC ID: N8WSUPER Report # 621779.DOC Page 3 of 11 FCC Part 18 Report GENERAL INFORMATION Product Description for Equipment Under Test (EUT) The Super Trend Lighting Limited’s FCC ID: N8WSUPER, model: EU-13W or the “EUT” as referred to in this report is a CFL which measures approximately 11.0cmL x 5.0cmW x 5.0cmH. rated input voltage: AC 120V/60 Hz. * The test data gathered are from production sample, serial number: 0601205, provided by the manufacturer Objective The following test report is prepared on behalf of Super Trend Lighting Limited in accordance with Part 2, Subpart J, and Part 18, Subparts A, B and C of the Federal Communication Commissions rules and regulations. The objective of the manufacturer is to determine compliance with FCC Part 18 limits. Related Submittal(s)/Grant(s) No related submittal(s). Test Methodology All measurements contained in this report were conducted with MP-5, FCC Methods of Measurements of Radio Noise Emissions from ISM Equipment, February 1986. All measurement was performed at Bay Area Compliance Laboratory Corporation. The radiated testing was performed at an antenna-to-EUT distance of 3 meters. Test Facility The Test site used by Bay Area Compliance Lab Corp. (ShenZhen) to collect radiated and conducted emission measurement data is located in the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone, ShenZhen, Guangdong 518038, P.R.China. Test site at Bay Area Compliance Lab Corp. (ShenZhen) has been fully described in reports submitted to the Federal Comm…

Text truncated - open the document above for the full version.

Test Setup Photos Conducted Emission - Front View Conducted Emission – Side View