NBZNRM-6835MINSTREL m500 Wireless CDPD Modem

March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 Exhibit 9 User’s Manual N N N N o o o o v v v v a a a a t t t t e e e e l l l l M M M M i i i i n n n n s s s s t t t t r r r r e e e e l l l l m m m m 5 5 5 5 0 0 0 0 0 0 0 0 Preface Caution To satisfy FCC RF exposure compliance requirements for portable transmitting devices, the user should generally maintain a separation distance of 4 cm between the person’s body, and the device and its antenna. The hands and wrists have a higher exposure limit because they are extremities, and the device should be used in a hand-held, hand-operated configuration only. This device has been tested for compliance with a separation distance of 4 cm from a person's body. The operating configurations of this device generally do not support normal transmissions while it is carried in pockets or holsters next to a person’s body. Technical Support If you have any questions or comments about your Minstrel m500, please contact the Novatel Wireless Technical Support Team. WWW:www.novatelwireless.com/support/index.html E-mail:[email protected] Phone:1-888-888-9231 Requirements The following items are required to set up and use your Minstrel m500: •A Palm m500/505 TM handheld computer; •Desktop software that allows you to communicate between your desktop PC and the Palm m500/505™; •Modem application software for the Palm m500/505™ (included with your Minstrel); •An account with a Wireless IP network service provider in your area; •Application software for your Palm m500/505™ such as an e-mail client and web browser. Wireless IP service is available from your local cellular carrier in most North American cities. Check your product packaging or www.novatelwireless.com for network provider contact information. Preface — Requirements The information contained in this document is subject to change without notice and should not be con- strued as a commitment by Novatel Wireless, Inc. unless such commitment is expressly given in a cover- ing document. The information herein is the exclusive property of Novatel Wireless Inc. No part of this publication may be reproduced or transmitted in any form or by any means including electronic storage, reproduction, execu- tion, or transmission without the prior written consent of Novatel Wireless, Inc. © 2000 Novatel Wireless, Inc. All rights reserved. Microsoft ® , Windows ® , Microsoft ® Pocket Internet Explorer, Microsoft ® Pocket Outlook, and Microsoft ® ActiveSync ® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All other brand names and product names used in this document are trade names, service marks, trademarks, or registered trademarks of their respective owners. N N N N o o o o v v v v a a a a t t t t e e e e l l l l M M M M i i i i n n n n s s s s t t t t r r r r e e e e l l l l m m m m 5 5 5 5 0 0 0 0 0 0 0 0 Contents Minstrel m500 Familiarization Status Indicator LEDs................................................................................ 2 Service Connection LED............................................................................................. 2 Data/Message Waiting LED........................................................................................3 Battery LED ................................................................................................................ 3 Pass Through Charging ............................................................................ 4 Configurable/Power Button ....................................................................... 4 The Antenna.............................................................................................. 4 The Release Button................................................................................... 4 The Serial Connector ................................................................................ 4 Setting Up the Minstrel m500 Charging the Battery ................................................................................. 5 Installing the Minstrel m500 Software ....................................................... 6 Connecting the Minstrel m500 to Your Palm m500/505™ ........................ 8 Removing the Minstrel m500 from Your Palm m500/505™ ...................... 9 Configuring the Minstrel m500 Starting the Configuration Process.......................................................... 11 Specifying Your Network Provider........................................................... 12 Using an Unlisted Network Provider .........................................................................13 Configuring the Palm m500/505™ Device .............................................. 13 Contact Your Network Provider............................................................... 14 IP Settings ............................................................................................... 15 Confirm the IP Settings ........................................................................... 15 Configuration Acknowledgment............................................................... 16 Checking the Network ............................................................................. 17 Finishing the Modem Configuration......................................................... 18 Configuring the Modem’s Button ............................................................. 18 iiContents Using the Modem Manager Connecting to the Network ............................................................................................. 21 Starting the Modem Manager Software................................................................................................21 Disconnecting from the Network ..........................................................................................................22 Closing the Active Network Session ..................................…

Text truncated - open the document above for the full version.

March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 Exhibit 10 Attestation Statements FCC Part 15, Subpart B Certificate of Conformity FCC Part 2 & 22 Statement of Compliance March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 PRODUCT: MODEL: Minstrel m500 MANUFACTURER: Novatel Wireless Technologies Inc. We certify that the pertinent tests have been performed on the above described equipment and that this equipment conforms to FCC Parts 2 and 22. See Exhibit 2, Engineering Reports, of this application.

March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 List of Exhibits Submitted E E X X H H I I B B I I T T 1 1 : : C C O O V V E E R R L L E E T T T T E E R R S S a)Application overview b)Equipment: Wireless CDPD modem for PDA, Minstrel m500,(Using an approved radio transmitter FCC ID:NRM-6832) c)Authorization Letter /Agent Designated (Jay Sarkar) d)Request for confidentiality e)Letter from Novatel Wireless. authorizing to use FCC approved (FCC ID NRM-6832) radio transmitter in Novatel Wireless Technologies, Inc.’s Minstrel m500 Exhibit 2:Engineering Reports (Test Reports) a)ERP (2.1046) b)Radiated Spurious Emissions (2.1053) c)Bandwidth (2.1049) Bandwidth Limitations (2.1047) d)Spurious Emissions, Antenna Terminal (2.1051) e)Frequency Stability (2.1055) Exhibit 3: Operational/Technical Description Exhibit 4: ID Label/Location Exhibit 5:External Photographs of the Equipment Internal Photographs of the equipment Exhibit 6:Block Diagram (Confidential) Exhibit 7: Schematic Diagram (Confidential) Exhibit 8:Parts List (Confidential), Tune–up Procedure Exhibit 9:User’s Manual Exhibit 10:a) Attestation Statement: FCC Part 15 Declaration of Conformance (DoC) certificate b)Attestation Statement: the equipment complies with Part 2 & 22 Exhibit 11:RF Exposure Information: SAR Report (Includes Test Set-up Photographs)

March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 Exhibit 1 a) Application overview b) Equipment: Wireless CDPD modem, (Using an approved radio modem FCC ID: NBZNRM-6832) c) Authorization Letter /Agent Designated (Jay Sarkar) d) Request for confidentiality e) Letter from Novatel Wireless Technologies. authorizing to use FCC approved (FCC ID NRM-6832) radio Transmitter in Novatel Wireless Technologies’ Wireless CDPD modem for PDA, model: Minstrel m500 March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 EQUIPMENT PRODUCT: Wireless Modem MODEL: Minstrel m500 MANUFACTURER: Novatel Wireless Technologies Inc. FCC ID: NBZNRM-6835 PRODUCT: Wireless CDPD modem MODEL: Minstrel m500 with a Novatel NRM6832 Transmitter (FCC ID: NBZNRM-6832) EUT TYPE: Licensed Non-Broadcast Station Transmitter (TNB) TX Frequency: 824-849 MHz MEASURED ERP:0.372W

* Consulting * Research * Training * Certification Testing Since 1981 51 Spectrum Waytel: (613) 820-2730 Nepean, Ontariovisit our Web Pages: www.aprel.comfax: (613) 820-4161 Canada K2R 1E6email: [email protected] May 7, 2001 Mr. Andy Leimer Federal Communications Commission Application Processing Branch 7435 Oakland Mills Road Columbia, Maryland 21046 Re:Question from the FCC FCC ID:NBZNRM-6835 Correspondence Reference Number:19081 731 Confirmation Number EA100427 Date of Original E-Mail:May 4, 2001 Dear Mr. Leimer: Pursuant to your e-mail to Mr. Owen Thistle, Novatel Wireless Technologies Ltd., I am forwarding to you our responses to item 1. The relevant portions of the FCC’s e-mail follow with our response inserted in the appropriate place: From: OET [mailto:[email protected]] Sent: Friday, May 04, 2001 7:01 AM To: Owen Thistle Subject: Spurious RE Measurements To: Owen Thistle, Novatel Wireless Technologies Ltd. From: Andy Leimer [email protected] FCC Application Processing Branch Re: FCC ID NBZNRM-6835 Applicant: Novatel Wireless Technologies Ltd Correspondence Reference Number: 19081 731 Confirmation Number: EA100427 1) It appears that the spurious RE measurements were not done using the substitution method. Repeat the measurements using the substitution method using a procedure similar to that described in the ERP measurement portion of the Test Report. The substitution method measurements are described in the document TIA/EIA - 603 Section 2.2.12. Response: The Minstrel m500 m500 was re-tested for spurious RE measurement using the substitution method using a procedure similar to that used in the ERP measurement and described in the ERP * Consulting * Research * Training * Certification Testing Since 1981 51 Spectrum Waytel: (613) 820-2730 Nepean, Ontariovisit our Web Pages: www.aprel.comfax: (613) 820-4161 Canada K2R 1E6email: [email protected] measurement portion of the Test Report. A set of three reference dipoles, a horn antenna and a signal generator to duplicate the signal were used. Signals radiated from the Minstrel m500 on the fundamental frequency as well as second and third harmonic were evaluated by comparing to the signals transmitted from the reference dipoles. The antenna used for the first three harmonics were a set of three dipoles, l = 17.9 cm (first harmonic/fundamental), l = 9.0 cm (second harmonic), and l = 6.0 cm (third harmonic). For testing the higher frequencies, fourth and fifth harmonics, a horn antenna (gain) was used as replacement source of radiation thus substituting the Minstrel m500. The duplicated reading was then referenced to the dipole. Finally, the duplicated readings were converted to dBμV/m. The data after the re-test is presented in the following two tables: Test Data using Substitution Method Vertical polarization fERP V E V @3mLimitMargin MHzdBMdBμV/mdBμV/mdB 1672.98-40.457.078.721.7 2509.47-50.247.278.731.5 3345.96-54.542.978.735.8 4182.45Noise FloorNoise Floor78.732.2 Horizontal polarization fERP V E V @3mLimitMargin MHzdBMdBμV/mdBμV/mdB 1672.98-62.135.378.743.4 2509.47-58.738.778.740.0 3345.96-54.443.078.735.7 4182.45Noise FloorNoise Floor78.731.6 I trust that the above will answer your inquiry. If not, please feel free to contact me. Regards, Jayanta (Jay) K.Sarkar Director Technical Director, Standards and Certification

March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 Exhibit 5 Photographs of the Equipment External Photos Internal Photos

March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 Exhibit 4 FCC ID Label/Location PART NUMBER REVISION NUMBER DESCRIPTION DATE CREATED PMS COLORS DO NOT SCALE/EDIT ARTWORK © 2001 Novatel Wireless, Inc. All Rights Reserved. AW-XXXXXXXX 1 This is art that will pad print directly to the back side of the plastic shell. It must be printed exactly where it appears here. 03/07/01 WHITE (represented by red) BACK SHELL MINSTREL m500 RED=WHITE BLACK= DO NOT PRINT. MINSTREL m500 FCC ID: NBZNRM-6835 CANADA: XXXX-XXXX Wireless Handheld Modem CDPD Network

March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 Exhibit 11 RF Exposure Information Sar Report Page 2 of 19 Project #3686: 51 Spectrum WayTel. (613) 820-2730 Nepean, Ontario, K2R 1E6 Fax (613) 820 4161 e-mail: [email protected] © APREL 2000 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories. FCC ID:NBZNRM-6835 Applicant:Novatel Wireless Technologies LTD. Equipment:Wireless CDPD Modem Model:Minstrel m500 Standard:FCC 96 –326, Guidelines for Evaluating the Environmental Effects of Radio- Frequency Radiation ENGINEERING SUMMARY This report contains the results of the engineering evaluation performed on the Novatel Minstrel m500 CDPD modem. The measurements were carried out in accordance with FCC 96-326. The Minstrel m500 was evaluated for its maximum power level 0.372(ERP) with a 100 % duty cycle. The Minstrel m500 CDPD modem is an attachment for a Palm PDA. The assembled device is intended to transmit while being operated from the user's hand. The Minstrel m500 was tested at low, middle and high channels for the keyboard up, keyboard down, and right sides. The maximum 10g SAR (1.89 W/kg) was found to coincide with the peak performance RF output power of channel 991 (824.04 MHz) for the keyboard down side of the device. (The hot spot is located on the antenna). Test data and graphs are presented in this report. At a separation distance of 4 cm from the antenna of the device, the maximum 1g SAR is 0.13 W/kg. The manual will include warning stating, bystanders, and parts of the user’s body other than extremities, must be at least 4 cm away from the antenna. Based on the test results and on how the device will be marketed and used, it is certified that the product meets the requirements as set forth in the above specifications, for the RF exposure environment. (The results presented in this report relate only to the sample tested.) Page 3 of 19 Project #3686: 51 Spectrum WayTel. (613) 820-2730 Nepean, Ontario, K2R 1E6 Fax (613) 820 4161 e-mail: [email protected] © APREL 2000 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories. Table of Contents 1.Introduction....................................................................................................................4 2.Applicable Documents...................................................................................................4 3.Device Under Investigation...........................................................................................4 4.Test Equipment..............................................................................................................5 5.Test Methodology..........................................................................................................5 6.Test Results....................................................................................................................6 6.1.Transmitter Characteristics............................................................................................6 6.2.SAR Measurements........................................................................................................7 7.User’s Hand Exposure...................................................................................................8 8.Bystander Exposure......................................................................................................9 9.Conclusions..................................................................................................................12 APPENDIX A. Measurement Setup, Tissue Properties and SAR Graphs.............................13 APPENDIX B. Uncertainty Budget........................................................................................15 APPENDIX C. Validation Scan on a Flat Phantom................................................................16 APPENDIX D. Probe Calibration...........................................................................................18 TABLES AND FIGURES Table 1. Sampled RF Power 6 Table 2.SAR Measurements 8 Table 3. SAR versus DUI-Phantom Separation 10 Table 4.Dielectric Properties of the Simulated Muscle Tissue at 835 MHz13 Table 5. Uncertainty Budget15 Figure1&2.PDA With DUI11 Figure3.PDA With DUI Side View11 Figure 4. Setup 13 Figure 5. Contour Plot of the Area Scan 2.5mm Above Phantom Surface 14 Figure 6. Surface Plot of the Area Scan 2.5mm Above Phantom Surface 14 Figure 7. Contour Plot of the Reference Area Scan 2.5mm Above Phantom 16 Figure 8. Surface Plot of the Reference Area Scan 2.5mm Above Phantom 16 Figure 9. Peak Local SAR versus Separation (1 gram SAR) 17 Page 4 of 19 Project #3686: 51 Spectrum WayTel. (613) 820-2730 Nepean, Ontario, K2R 1E6 Fax (613) 820 4161 e-mail: [email protected] © APREL 2000 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories. 1. INTRODUCTION Tests were conducted to determine the Specific Absorption Rate (SAR) for a sample Novatel Minstrel m500. These tests were conducted at APREL Laboratories’ facility located at 51 Spectrum Way, Nepean, Ontario, Canada. A view of the SAR measurement setup can be seen in Appendix A Figure 1. This report describes the results obtained. 2. APPLICABLE DOCUMENTS The following documents are applicable to the work performed: 1) FCC 96-326, Guidelines for Evaluating the Environmental Effects of Radio- Frequency Radiation 2) ANSI/IEEE C95.1-1999, IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. 3) ANSI/IEEE C95.3-1992, IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields – RF and Microwave. 4) OET Bulletin 65 (Edition 97-01) Supplement C (Edition 97-01), “Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields”. 3. D…

Text truncated - open the document above for the full version.

March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 Exhibit 2 Engineering Report a)ERP (2.1046) Assessment of Compliance for Measurement of Effective radiated Power (ERP) in Accordance with the FCC Rules & Regulations Part 2.1046 Wireless CDPD Modem Minstrel m500 Novatel Wireles Technologies Ltd. 51 Spectrum Way Nepean ON K2R 1E6 Tel: (613) 820-2730 Fax: (613) 820-4161 email: [email protected] March 2001 NVWB-Palm Xyclone Minstrel M500-3689 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories FCC ID:NBZNRM-6835 Applicant:Novatel Wireless Technologies Ltd. Equipment:Wireless CDPD Modem Model:Minstrel m500 Standard:FCC Rules and Regulations Part 2.1046 & 22 ENGINEERING SUMMARY This report contains the results of the effective radiated power (ERP) measurement performed on a NOVATEL WIRELESS Minstrel m500 wireless CDPD modem. The measurements were carried out in accordance with the FCC Rules and Regulations Part 2.1046 & 22. The product was evaluated for ERP when it was set at the maximum power level. Minstrel m500 was tested for ERP at high, middle, and low frequencies with the maximum ERP obtained at channel No.: 991 with the frequency being 824.0 MHz. The test data is presented in this report under the section: Test Results. The measured ERP is 0.372 W. (The results presented in this report relate only to the sample tested) March 2001 Page 2 APREL Project No NVWB- Palm Xyclone Minstrel M500-3689 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories March 2001 Page 3 APREL Project No NVWB- Palm Xyclone Minstrel M500-3689 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 Summary of the Results Test DescriptionPage No. Test Set-up Figure No. Results Summary RF Power Output as Radiated Ref. Paragraph 2.1046 & 2281Passed March 2001 Page 4 APREL Project No NVWB- Palm Xyclone Minstrel M500-3689 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 INTRODUCTION General This report describes the results of the effective radiated power (ERP) measurement conducted on a Novatel Wireless Minstrel m500 wireless CDPD modem herein referred to as DUI (Device under Investigation) Test Facility The tests were performed for Novatel by APREL Laboratories at APREL’s EMI facility located in Nepean, Ontario, Canada. The laboratory operates an (3m and 10m) Open Area Test Site (OATS). The measurement facility is calibrated in accordance with ANSI C63.4-1992. A description of the measurement facility in accordance with the radiated and AC line conducted test site criteria per ANSI C63.4-1992 is on file with the Federal Communications Commission and is in compliance with the requirements of Section 2.948 of the Commissions rules and regulations. APREL’s registration number is: 90416 APREL is accredited by Standard Council of Canada, under PALCAN program (ISO Guide 25). APREL is also accredited by Industry Canada (formerly DOC) and recognised by the Federal Communications Commissions (FCC). Standard The evaluation and analysis were conducted in accordance with FCC Rules and Regulations Parts 2.1046 and 22. Test Equipment The test equipment used during the evaluation is listed in Appendix A with calibration due dates. Environmental Conditions Measurements were conducted in open area test site. - Temperature:15 °C ± 2 - Relative Humidity:30 - 50 % March 2001 Page 5 APREL Project No NVWB- Palm Xyclone Minstrel M500-3689 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 - Air Pressure:101 kPa ± 3 FCC SUBMISSION INFORMATION FCC ID:NBZNRM-6835 Equipment:Wireless CDPD Modem Model:Minstrel m500 For:Certification Applicant:Novatel Wireless Technologies Ltd. Suite 200 6715-8 th Street, N.E. Calgary, Alberta Canada, T2E 7H7 Manufacturer: Novatel Wireless Technologies Ltd. Suite 200 6715-8 th Street, N.E. Calgary, Alberta Canada, T2E 7H7 Evaluated by:APREL Laboratories 51 Spectrum Way Nepean, Ontario Canada K2R 1E6 March 2001 Page 6 APREL Project No NVWB- Palm Xyclone Minstrel M500-3689 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 MANUFACTURER’S DATA FCC ID No:NBZNRM-6835 Equipment Type:Wireless CDPD Modem Model:Minstrel m500 Reference:FCC Rules and Regulations Parts 2 and Part 22 Manufacturer:Novatel Wireless Technologies Ltd. Power Source:DC Battery Development Stage of Unit:Production GENERAL SPECIFICATIONS 1.Frequency Range:824 to 849 MHz (Transmitter) 2.Output Power:0.372 W ERP 3. Frequency Tolerance:2.5 ppm 4.Type of Modulation:GMSK 5.Emission Designators(See 47 CFR § 2.201 and §2.202) 28K8FXW 6. Antenna Impedance:50 Ohms March 2001 Page 7 APREL Project No NVWB- Palm Xyclone Minstrel M500-3689 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 N N o o v v a a t t e e l l W W i i r r e e l l e e s s s s TEST RESULTS FOR Effective Radiated Power (ERP) Of Novatel Minstrel m500 Wireless CDPD modem March 2001 Page 8 APREL Project No NVWB- Palm Xyclone Minstrel M500-3689 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 Test:RF Power Output as Radiated (ERP) Ref.:FCC Part 2 paragraph 2.1046 and 22 Criteria:N/A Set-up:See Figure No. 1. Equipment:See Appendix A. Methodology:RF Powe…

Text truncated - open the document above for the full version.

March 2001 APREL Project No.: Consulting * Research * Training * Certification Testing Since 1981 FCC ID: NBZNRM-6835 Exhibit 2 Engineering Reports b)Radiated Spurious Emissions (2.1053) Assessment of Compliance for Measurement of Field Strength of Spurious Radiation in Accordance with the FCC Rules & Regulations Part 2.1053 Wireless CDPD Modem Minstrel M500 Novatel Wireless Technologies Ltd. 51 Spectrum Way Nepean ON K2R 1E6 Tel: (613) 820-2730 Fax: (613) 820-4161 email: [email protected] March 2001 NVWB-Palm Xyclone Minstrel M500-3690 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories March 2001 Page 2 APREL Project No NVWB- Palm Xyclone Minstrel M500-3690 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories FCC ID:NBZNRM-6835 Applicant:Novatel Wireless Technologies Ltd. Equipment:Wireless CDPD Modem Model:Minstrel m500 Standard:FCC Rules and Regulations Part 2.1046 & 22 ENGINEERING SUMMARY This report contains the results of Field Strength of Spurious Radiation measurement performed on a Novatel Wireless Minstrel m500 wireless CDPD modem. The measurements were carried out in accordance with the FCC Rules and Regulations Part 2.1053 & 22. The product was evaluated for spurious emissions when it was set at the maximum power level. The Minstrel m500 wireless CDPD modem is an attachment for Palm PDA . (The results presented in this report relate only to the sample tested) March 2001 Page 3 APREL Project No NVWB- Palm Xyclone Minstrel M500-3690 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 Summary of the Results Test DescriptionPage No. Test Set-up Figure No. Results Summary Field Strength of Spurious Radiation Ref. Paragraph 2.1053 & 2281Passed March 2001 Page 4 APREL Project No NVWB- Palm Xyclone Minstrel M500-3690 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 INTRODUCTION General This report describes the results of the Field Strength of Spurious Radiation measurement conducted on a Novatel Wireless Minstrel m500 CDPD modem herein referred to as DUI (Device Under Investigation). Test Facility The tests were performed for Novatel Wireless by APREL Laboratories at APREL’s EMI facility located in Nepean, Ontario, Canada. The laboratory operates an (3m and 10m) Open Area Test Site (OATS). The measurement facility is calibrated in accordance with ANSI C63.4-1992. A description of the measurement facility in accordance with the radiated and AC line conducted test site criteria per ANSI C63.4-1992 is on file with the Federal Communications Commission and is in compliance with the requirements of Section 2.948 of the Commissions rules and regulations. APREL’s registration number is 90416 APREL is accredited by Standard Council of Canada, under PALCAN program (ISO Guide 25). APREL is also accredited by Industry Canada (formerly DOC) and recognised by the Federal Communications Commissions (FCC). Standard The evaluation and analysis were conducted in accordance with FCC Rules and Regulations Parts 2.1053 & 22. Test Equipment The test equipment used during the evaluation is listed in Appendix A with calibration due dates. Environmental Conditions Measurements were conducted in open area test site. - Temperature:20 °C ± 2 - Relative Humidity:30 - 50 % - Air Pressure:101 kPa ± 3 March 2001 Page 5 APREL Project No NVWB- Palm Xyclone Minstrel M500-3690 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 FCC SUBMISSION INFORMATION FCC ID:NBZNRM-6835 Equipment:Wireless CDPD Modem Model:Minstrel m500 For:Certification Applicant:Novatel Wireless Technologies Ltd. Suite 200 6715-8 th Street, N.E. Calgary, Alberta Canada, T2E 7H7 Manufacturer: Novatel Wireless Technologies Ltd. Suite 200 6715-8 th Street, N.E. Calgary, Alberta Canada, T2E 7H7 Evaluated by:APREL Laboratories 51 Spectrum Way Nepean, Ontario Canada K2R 1E6 March 2001 Page 6 APREL Project No NVWB- Palm Xyclone Minstrel M500-3690 This report shall not be reproduced, except in full, without the express written approval of APREL Laboratories Consulting * Research * Training * Certification Testing Since 1981 MANUFACTURER’S DATA FCC ID No:NBZNRM-6835 Equipment Type:Wireless CDPD Modem Model:Minstrel m500 Reference:FCC Rules and Regulations Parts 2 and Part 22 Manufacturer:Novatel Wireless Technologies Ltd. Power Source:DC Battery Development Stage of Unit:Production GENERAL SPECIFICATIONS 1.Frequency Range:824 to 849 MHz (Transmitt…

Text truncated - open the document above for the full version.