NCT12BP10Industrial Radio Remote Controller

Gain Electronic Co., Ltd. www.sagaradio.com.tw SAGA1-P10 Series User Manual S S A A F F E E T T Y Y / / R R E E L L I I A A B B I I L L I I T T Y Y / / U U S S E E R R - - F F R R I I E E N N D D L L Y Y Industrial Radio Remote Controller Warning and Caution The following symbols may be found on the product or throughout the documentation. Symbol Description Refer to Manual Refer the user manual for additional information when product marked with this sign. Dangerous Voltage Indicates presence of hazardous voltage. Unsafe practice could result in severe personal injury. Warning Denotes a hazard. Included text gives proper procedures. Failure to follow instructions could result in severe personal injury and/or property damage. Caution Denotes a hazard. Included text gives proper procedures.Failure to follow instructions could result in minor personal injury and/or properly damage. FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. (3) Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IMPORTANT NOTE FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between radiator & your body. Industry Canada Notice Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Industry Canada Caution This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'IndustrieCanadaapplicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Warranty Warranty Gain Electronic Co., Ltd. guarantees that this equipment meets its published specifications at the time of shipment from the factory. This equipment will perform as described if installed properly. However, Gain can't guarantee that operation in SAGA 1 system is absolutely error-free, or without interruption. Warranty Period This equipment is warranted against defects in materials and workmanship for a period of one year from the date of shipment. During the warranty period, Gain is responsible for necessary repairs as long as the product can be proved to be defective. For warranty service or repair, this equipment must be returned to a service facility designated by Gain. Customer is responsible for shipping charges to Gain, while Gain will pay return shipping charges. Excluded Items This warranty doesn't include consumable parts such as Joystick, batteries, fuses, buttons and relays. Also this warranty doesn't cover defects caused by improper installation, improper or insufficient maintenance unauthorized modification, unavoidable natural essential, improper operation, ignorance of environmental specifications, improper software/interfacing. Remarks 1. No other warranty is expressed or implied, except for the above mentioned. 2. The remedies provided herein are the buyers' sole and exclusive remedies. Gain shall not be liable for any direct/indirect, special, incidental or consequential damages. Important Information before You Start Important 1. Read this manual carefully before operating and installation. 2. Due to the complex nature of equipment, it is necessary to read the entire manual before installation. 3. Never allow any unauthorized personnel to dismantle equipment as this may cause the equipment damage. 4. The equipment has been stringently tested for quality assurance before delivery from factory. However, it must not be used in extremely dangerous situations, or where damage may result. 5. After operation, switch off crane main power as well as receiver unit and remove rotary key from transmitter unit. 6. The transmitter should keep in a safe place when not in use to avoid any unintentionally operation. 7. The crane should be equipped with main power relay, limit switch and other safety devices required. 8. Do not use this device during electrical storm or where there are conditions of high electrical interference. 9. Always check transmitter battery and receiver input power condition before operation. 10. The installation and maintenance service is allowed only when the crane and receiver power are off to avoid electrical shock. 11. The contents of the manual may be amended by the manufacturer without notice. 12. The specification and function is subjected to change without notice by manufacturer. Precautions 1. Press EMS button and switch off main power of crane and receiver after operation. Then remove transmitter rotary key and keep in a safe place. 2. The following situations may cause receiver response delay and stop operation immediately when situation occurs. (a) Beyond operating range (b) During severe radio interference 3. Remove transmitter batteries when not in use for long period of time. 4. To extend product life, please follow the standard operating procedure and maintain system regularly. 5. Check EMS button and other system main functions before operation. 6. Press EMS button during system failure or any abnormal conditions occur. 7. The oper…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.：T121114N02-RP1 Page A1 / 6 External Photo (SAGA1-P10)

g Company : Gain Electronic Co., Ltd. Model: SAGA1-P10 Product : Industrial Radio Remote Controller Label Here Model No: SAGA1-P10 FCC ID: NCT12BP10 IC:2802A-12BP10 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Model No: SAGA1-P10-1 FCC ID: NCT12BP10 IC:2802A-12BP10 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Model No: SAGA1-P8 FCC ID: NCT12BP10 IC:2802A-12BP10 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Model No: SAGA1-P8-1 FCC ID: NCT12BP10 IC:2802A-12BP10 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Model No: SAGA1-P6 FCC ID: NCT12BP10 IC:2802A-12BP10 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Model No: SAGA1-P6-1 FCC ID: NCT12BP10 IC:2802A-12BP10 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Model No: SAGA1-P4 FCC ID: NCT12BP10 IC:2802A-12BP10 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Model No: SAGA1-P4-1 FCC ID: NCT12BP10 IC:2802A-12BP10 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Compliance Certification Services Inc. Report No.：T121114N02-RP1 Page A2 / 6 Internal Photo (SAGA1-P10) Antenna Compliance Certification Services Inc. Report No.：T121114N02-RP1 Page A3 / 6 Compliance Certification Services Inc. Report No.：T121114N02-RP1 Page A4 / 6 Compliance Certification Services Inc. Report No.：T121114N02-RP1 Page A5 / 6 Compliance Certification Services Inc. Report No.：T121114N02-RP1 Page A6 / 6

Model No.: SAGA1-P10 ISO 9001 TYPE: Whip FREQUENCY: 910.146MHz ~ 925.906 MHz GAIN(dBi) ≦0 V.S.W.R. ≦1.2 POLARIZATION Elliptical Polarization Power Capability ≦0.3W INPUT CONNECTOR 2.0 connect female Radiation Element Material Wire Dimension(mm) See Figure1 Impedance 50Ω Weight 1g Figure1 75mm

Compliance Certification Services Inc. FCC ID: NCT12BP10 Report No.: T121114N02-RP1 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1/ 32 FCC 47 CFR PART 15 SUBPART C ANSI C63.4: 2003 TEST REPORT For Industrial Radio Remote Controller MODEL: SAGA1-P10 DATA APPLIES TO: SAGA1-P10-1; SAGA1-P8; SAGA1-P8-1; SAGA1-P6; SAGA1-P6-1; SAGA1-P4; SAGA1-P4-1 BRAND: SAGA Issued to GAIN ELECTRONIC CO., LTD 4F-1, NO.288-5, HSIN YA RD, CHIEN CHEN ZONE (806), KAOHSIUNG, TAIWAN, ROC Issued by Compliance Certification Services Inc. Tainan Lab. No.8,Jiucengling, Xinhua Dist., Tainan City 712, Taiwan (R.O.C.) TEL: (06) 580-2201 FAX: (06) 580-2202 Issued Date: December 18, 2012 Compliance Certification Services Inc. FCC ID: NCT12BP10 Report No.: T121114N02-RP1 Page 2 / 40 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 December 3, 2012 Initial Issue ALL Eva Lin 01 December 14, 2012 Update test data Page 28-30 Eva Lin 02 December 18, 2012 Revised data Page 26-27 Eva Lin Compliance Certification Services Inc. FCC ID: NCT12BP10 Report No.: T121114N02-RP1 Page 3 / 40 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION .........................................................................4 2. EUT DESCRIPTION..............................................................................................5 3. TEST METHODOLOGY........................................................................................8 3.1 EUT CONFIGURATION ...................................................................................8 3.2 EUT EXERCISE ...............................................................................................8 3.3 GENERAL TEST PROCEDURES ....................................................................8 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ........................9 3.5 DESCRIPTION OF TEST MODES...................................................................9 4. INSTRUMENT CALIBRATION...........................................................................10 4.1 MEASURING INSTRUMENT CALIBRATION ................................................10 4.2 MEASUREMENT EQUIPMENT USED ..........................................................10 4.3 MEASUREMENT UNCERTAINTY .................................................................11 5. FACILITIES AND ACCREDITATIONS ...............................................................12 5.1 FACILITIES ....................................................................................................12 5.2 EQUIPMENT ..................................................................................................12 5.3 LABORATORY ACCREDITATIONS LISTING ...............................................12 5.4 TABLE OF ACCREDITATIONS AND LISTINGS............................................13 6. SETUP OF EQUIPMENT UNDER TEST ............................................................14 6.1 SETUP CONFIGURATION OF EUT ..............................................................14 6.2 SUPPORT EQUIPMENT................................................................................14 7. FCC PART 15.249 REQUIREMENTS ................................................................15 7.1 20 DB BANDWIDTH.......................................................................................15 7.2 BAND EDGES MEASUREMENT ...................................................................18 7.3 DUTY CYCLE.................................................................................................19 7.4 SPURIOUS EMISSION..................................................................................21 7.5 POWERLINE CONDUCTED EMISSIONS .....................................................37 APPENDIX I - PHOTOGRAPHS OF TEST SETUP .................................................38 APPENDIX II - PHOTOGRAPHS OF EUT .............................................................. A1 Compliance Certification Services Inc. FCC ID: NCT12BP10 Report No.: T121114N02-RP1 Page 4 / 40 1. TEST RESULT CERTIFICATION Product: Industrial Radio Remote Controller Model: SAGA1-P10 Data Applies To: SAGA1-P10-1; SAGA1-P8; SAGA1-P8-1; SAGA1-P6; SAGA1-P6-1; SAGA1-P4; SAGA1-P4-1 Brand Name: SAGA Applicant: GAIN ELECTRONIC CO., LTD 4F-1, NO.288-5, HSIN YA RD, CHIEN CHEN ZONE (806), KAOHSIUNG, TAIWAN, ROC Manufacturer: GAIN ELECTRONIC CO., LTD 4F-1, NO.288-5, HSIN YA RD, CHIEN CHEN ZONE (806), KAOHSIUNG, TAIWAN, ROC Tested: November 19, 2012 – November 23, 2012 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C ANSI C63.4 : 2003 No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2003 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements emission limits of FCC Rules Part 15.107, 15.109,15.207, 15.209 and 15.249. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Jeter Wu Assistant Manager Eric Huang Assistant Section Manager Compliance Certification Services Inc. FCC ID: NCT12BP10 Report No.: T121114N02-RP1 Page 5 / 40 2. EUT DESCRIPTION Product Industrial Radio Remote Controller Model Number SAGA1-P10 Data Applies To SAGA1-P10-1; SAGA1-P8; SAGA1-P8-1; SAGA1-P6; SAGA1-P6-1; SAGA1-P4; SAGA1-P4-1 Brand Name SAGA Received Date November 14, 2012 Frequency Range 910.146 MHz to 925.906 MHz Transmit Peak Power 87.94 dBμV/m Data Rate 4.8 kbps Number of Channels 160 Channels Type of Modulation FSK Power Supply 6Vdc Antenna Type Whip antenna Gain: 0 dBi≦ Temp…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. FCC ID: NCT12BP10 Report No.: T121114N02-RP1 Page 38 / 40 APPENDIX I - PHOTOGRAPHS OF TEST SETUP RADIATED RF EMISSION MEASUREMENT SETUP Compliance Certification Services Inc. FCC ID: NCT12BP10 Report No.: T121114N02-RP1 Page 39 / 40 Compliance Certification Services Inc. FCC ID: NCT12BP10 Report No.: T121114N02-RP1 Page 40 / 40 RADIATED EMISSION SETUP -