NEOA207SERIESMBF-T-8-17-19S Tri Band Repeater

OMU Optical Master Unit © Axell Wireless Ltd Optical Master Unit PRODUCT DESCRIPTION AND USER’S MANUAL © Axell Wireless Ltd A1829300 rev H 1 (86) Optical Master Unit, OMU Product Description and User’s Manual This manual is valid for Firmware release version Š Common Commands and Attributes v 1.3.0 Š OMU Commands and Attributes v 1.0.0 Copyright © 2009 Axell Wireless Ltd All rights reserved. No part of this document may be copied, distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language without the prior written permission of Axell Wireless Ltd. The manufacturer has made every effort to ensure that the instructions contained in this document are adequate and free of errors and omissions. The manufacturer will, if necessary, explain issues which may not be covered by this document. The manufacturer's liability for any errors in the document is limited to the correction of errors and the aforementioned advisory services. This document has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using them. The manufacturer welcomes customer comments as part of the process of continual development and improvement of the documentation in the best way possible from the user's viewpoint. Please submit your comments to the nearest Axell Wireless sales representative. Optical Master Unit PRODUCT DESCRIPTION AND USER’S MANUAL © Axell Wireless Ltd A1829300 rev H 2 (86) Ta b l e o f C o n t e n t s Safety Instructions and Warnings.................................................................................................. 4 References ..................................................................................................................................... 5 Contact Information....................................................................................................................... 4 Definitions, Abbreviations and Acronyms ................................................................................... 7 1 Repeater Technology ................................................................................................................10 1.1 Basic Repeater Features ....................................................................................................10 1.2 Software Overview ............................................................................................................10 2 Product and System Description..............................................................................................12 2.1 Overview ...........................................................................................................................12 2.2 Building Blocks ................................................................................................................. 16 2.3 Block Diagram ..................................................................................................................24 2.4 Back Panel.........................................................................................................................25 2.5 Radio Signal and Data Communication Paths ...................................................................26 3 Monitoring and Control ........................................................................................................... 27 3.1 Software Features - Overview ...........................................................................................27 3.2 Network Nodes..................................................................................................................28 3.3 Fibre Loss Compensation and Master Volume..................................................................30 3.4 Alarm System .................................................................................................................... 31 3.5 OMU Heartbeat .................................................................................................................43 3.6 Hardware Identification.....................................................................................................51 3.7 ID and TAG....................................................................................................................... 51 3.8 User Access ....................................................................................................................... 52 3.9 Integration into AEM ........................................................................................................53 3.10 Upgrading Firmware .........................................................................................................53 4 Installation .................................................................................................................................54 4.1 Unpack the OMU ..............................................................................................................54 4.2 Mount the OMU ................................................................................................................54 4.3 Ensure Proper Grounding ..................................................................................................54 4.4 Attach Cabling................................................................................................................... 55 4.5 Start-up the OMU ..............................................................................................................59 4.6 Initiate Local Communication ...........................................................................................61 4.7 Configure the OMU...........................................................................................................62 4.8 Set Up OMU-Repeater System..........................................................................................63 4.9 Balance the System ..................................................…

Text truncated - open the document above for the full version.

Overview Connectors

11 22 33 44 55 66 77 88 A A B B C C D D E E F F A2 Drawing No Title First AngleProjection Drawn Date Checked Approved THIS IS A PROPRIETARY DESIGN OF AXELL WIRELESS LTDREPRODUCTION OR USE OF THIS DESIGN BY OTHER ISPERMISSABLE ONLY IF EXPRESSLY AUTHORISED IN WRITINGBY AXELL WIRELESS LTD SCALE ALL DIMENSIONS ARE IN mmUNLESS OTHERWISE STATED REVISION No DESCRIPTION DATE BY UNLESS STATED OTHERWISE ISO 2768-1 MEDIUM GENERAL TOLERANCES PerW 2008-11-24 PerW 2008-11-24 AA 2009-11-24 Tel : +46 (0)8 475 4700Fax : +46 (0)8 475 4799 Sheet 1 / 1 Rev. LABEL

REPORT ON THE CERTIFICATION TESTING OF A AXELL WIRELESS MBF TRI BAND REPEATER MBF-T-8-17-19S WITH RESPECT TO FCC RULES CFR 47, PARTS 22, Subpart C 24, Subpart E and 27, Subpart A TEST REPORT NO: 8F2093WUS1 COPY NO: 1 ISSUE NO: 1 FCC ID: NEOA207SERIES REPORT ON THE CERTIFICATION TESTING OF A AXELL WIRELESS MBF TRI BAND REPEATER MBF-T-8-17-19S WITH RESPECT TO FCC RULES CFR 47, PARTS 22, Subpart C 24, Subpart E and 27, Subpart A TEST DATE: 4 th – 23 rd September 2009 TESTED BY: D WINSTANLEY APPROVED BY: J CHARTERS RADIO PRODUCT MANAGER DATE: 10 th December 2009 Distribution: Copy Nos: 1. Axell Wireless 2. TCB: TRaC EMC & Safety 3. TRaC Telecoms & Radio THIS DOCUMENT MAY BE REPRODUCED ONLY IN ITS ENTIRETY AND WITHOUT CHANGE 9F2093WUS1 Page 3 of 129 CONTENTS PAGE CERTIFICATE OF CONFORMITY & COMPLIANCE 4 APPLICANT’S SUMMARY 5 RULE PART – FREQUENCY BAND 5 EQUIPMENT TEST CONDITIONS 6 TESTS REQUIRED 6 TEST RESULTS 7 - 119 ANNEX PHOTOGRAPHS A PHOTOGRAPH No. 1: Test setup PHOTOGRAPH No. 2: Overview APPLICANT’S SUBMISSION OF DOCUMENTATION LIST B EQUIPMENT CALIBRATION C MEASUREMENT UNCERTAINTY D Notes: 1. Component failure during test YES NO [ ] [X] 2. If Yes, details of failure: 3. The facilities used for the testing of the product contain in this report are FCC Listed. CERTIFICATE OF CONFORMITY & COMPLIANCE 8F2093WUS1 FCC IDENTITY: NEOA207SERIES PURPOSE OF TEST: Certification TEST SPECIFICATION: FCC RULES CFR 47, Parts 2, 22, 24 &27 TEST RESULT: Compliant to Specification EQUIPMENT UNDER TEST: MBF-T-8-17-19S EQUIPMENT TYPE: Private Land Mobile Repeater MAXIMUM GAIN: 800 MHz Uplink 1700 MHz Uplink 1800 MHz Uplink 800 MHz Downlink 1900 MHz Downlink 2100 MHz Downlink 32.65 dB 28.52 dB 26.81 dB 31.28 dB 29.69 dB 30.21 dB MAXIMUM INPUT: 800 MHz Uplink 1700 MHz Uplink 1800 MHz Uplink 800 MHz Downlink 1900 MHz Downlink 2100 MHz Downlink -61.65 dBm -58.88 dBm -59.20 dBm +4.68 dBm +6.71 dBm +8.56 dBm MAXIMUM OUTPUT CONDUCTED: 800 MHz Uplink 1700 MHz Uplink 1800 MHz Uplink 800 MHz Downlink 1900 MHz Downlink 2100 MHz Downlink -29.00 dBm -30.36 dBm -32.39 dBm +35.96 dBm +36.40 dBm +38.77 dBm MAXIMUM NUMBER OF CHANNELS: Not Applicable, Wideband CHANNEL SPACING: Not Applicable, Wideband POWER SOURCE(s): +110Vac TEST DATE(s): 4 th – 23 rd September 2009 APPLICANT: Axell Wireless ADDRESS: Aerial House Asheridge Road Chesham Buckinghamshire HP5 1TU TESTED BY: D WINSTANLEY APPROVED BY: J CHARTERS RADIO PRODUCT MANAGER 9F2093WUS1 Page 5 of 129 APPLICANT’S SUMMARY EQUIPMENT UNDER TEST (EUT): MBF-T-8-17-19S EQUIPMENT TYPE: Private Land Mobile Repeater PURPOSE OF TEST: Certification TEST SPECIFICATION(s): FCC RULES CFR 47, Parts 2, 22, 24 &27 TEST RESULT: COMPLIANT Yes No [X] [ ] APPLICANT’S CATEGORY: MANUFACTURER IMPORTER DISTRIBUTOR TEST HOUSE AGENT [X] [ ] [ ] [ ] [ ] APPLICANT’S CONTACT PERSON(s): Mr Peter Bradfield E-mail address: [email protected] APPLICANT: Axell Wireless ADDRESS: Aerial House Asheridge Road Chesham Buckinghamshire HP5 1TU United Kingdom TEL: +44 (0)1494 777000 FAX: +44 (0)1494 778456 MANUFACTURER: Axell Wireless EUT(s) COUNTRY OF ORIGIN: United Kingdom TEST LABORATORY: TRaC Telecoms & Radio, Up Holland UKAS ACCREDITATION No: 0971 TEST DATE(s): 4 th – 23 rd September 2009 TEST REPORT No: 8F2093WUS1 RULE PART – FREQUENCY BAND CFR 47 Rule Part Uplink Frequency Band Downlink Frequency Band 22, Subpart C 824.0 MHz – 849.0 MHz 869.0 MHz – 894.0 MHz 24, Subpart E 1850.0 MHz – 1910.0 MHz 1930.0 MHz – 1990.0 MHz 27, Subpart A 1710.0 MHz - 1755.0 MHz 2110.0 MHz – 2155.0 MHz 9F2093WUS1 Page 6 of 129 EQUIPMENT TEST / EXAMINATIONS REQUIRED 1. TEST/EXAMINATION RULE PART(s) APPLICABILITY RESULT RF Power Output 2.1046 Yes Complies Audio Frequency Response TIA EIA-603.3.2.6 N/A N/A Audio Low-Pass Filter Response TIA EIA-603.3.2.6 N/A N/A Modulation Limiting TIA EIA-603.3.2.6 N/A N/A Occupied Bandwidth 2.1049 Yes Complies Spurious Emissions at Antenna Terminals 2.1053 Yes Complies Field Strength of Spurious Emissions 2.1053 Yes Complies Frequency Stability N/A N/A(note 1) N/A Transient behaviour N/A N/A(note 2) N/A Notes: 1 The EUT does not contain modulation circuitry; therefore the test was not performed. 2 The EUT is not a keyed carrier system; therefore the test was not performed. Uplink Class A [ ] Class B [X] 2. Product class: Downlink Class A [ ] Class B [X] 3. Product Use: Private Land Mobile Repeater 4. Emission Designator: F3E 5. Temperatures: Ambient (Tnom) 24 o C 6. Supply Voltages: Vnom +110Vac Note: Vnom voltages are as stated above unless otherwise shown on the test report page Single channel [ ] Two channel [ ] 7. Equipment Category: Multi-channel [X] 8. Channel spacing: Narrowband [ ] Wideband [X] 9. Test Location TRaC Telecoms & Radio Up Holland [X] Hull [ ] 10. Modifications made during test program No modifications were performed. 9F2093WUS1 Page 7 of 129 COMPLIANCE TESTS AMPLIFIER GAIN – CONDUCTED – PART 2.1046 – UPLINK Ambient temperature = 20 o C Radio Laboratory Relative humidity = 63% Supply voltage = +110Vac Channel number = See test results 800 MHz UPLINK Frequency MHz Signal Generator input level dBm Input Cable Loss dB Output Cable & Attenuator loss dB Level at Spectrum Analyser dBm Gain dB Conducted Output Power dBm Gain after 10dB input level increase dB 824.0 -59.9 0.51 0.51 -29.43 31.49 -28.92 21.52 836.5 -61.2 0.45 0.48 -29.48 32.65 -29.00 22.68 849.0 -59.3 0.49 0.51 -29.63 30.68 -29.11 20.71 Notes: 1. The signal generator input was increased by 10dBs and the level of the output signal remeasured. 1700 MHz UPLINK Frequency MHz Signal Generator input level dBm Input Cable Loss dB Output Cable & Attenuator loss dB Level at Spectrum Analyser dBm Gain dB Conducted Output Power dBm Gain after 10dB input level increase dB 1710.0 -58.15 0.65 0.77 -30.67 28.25 -29.90 18.25 1732.5 -58.88 0.77 0.77 -31.13 28.52 -30.36 18.55 1755.0 -58.46 0.59 0.59 -31.06 27.99 -30.47 18.01 Notes: 2. The signal generator input was increased by 10dBs and the level of the output signal remeasured. 18…

Text truncated - open the document above for the full version.