
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
SYNTHESIZED VHF TELEMETRY UNIT PART NO. 242-3422-XYZ Third Printing September 1998 Supersedes 001-3422-002 February 1998 Part No. 001-3422-003 U.S.A. SYNTHESIZED VHF TELEMETRY UNIT PART NO. 242-3422-XYZ Copyrightο 1998 by the Johnson Data Telemetry Corporation. The Johnson Data Telemetry Corporation designs and manufactures radios and radio modems to serve a wide variety of data communication needs. The Johnson Data Telemetry Corporation produces equipment for the fixed data market including SCADA systems for utilities, petrochemical, waste and fresh water management markets and RF boards for OEM applications in the Radio Frequency Data Capture market. DATA TELEMETRY PRODUCT WARRANTY The manufacturer's warranty statement for this product is available from your product supplier or from the Johnson Data Telemetry Corporation, 299 Johnson Avenue, PO Box 1733, Waseca, MN 56093-0833. Phone (507) 835-8819. WARNING This device complies with Part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference. In addition, changes or modification to this equipment not expressly approved by Johnson Data Telemetry Corporation could void the user's authority to operate this equipment (FCC rules, 47CFR Part 15.19). DO NOT allow the antenna to come close to or touch, the eyes, face, or any exposed body parts while the radio is transmitting. DO NOT operate the radio near electrical blasting caps or in an explosive atmosphere. DO NOT operate the radio unless all the radio frequency connectors are secure and any open connectors are properly terminated. DO NOT allow children to operate transmitter equipped radio equipment. SAFETY INFORMATION Proper operation of this radio will result in user exposure below the Occupational Safety and Health Act and Federal Communication Commission limits. The information in this document is subject to change without notice. β’ is a trademark of the Johnson Data Telemetry Corporation. 1 TABLE OF CONTENTS 1GENERAL INFORMATION 1.1SCOPE OF MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.2EQUIPMENT DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 DL-3422 WITH LOADER BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 DL-3422 WITH DL-3295 MODEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 DM-3422 SYNTHESIZER PROGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.3TRANSCEIVER IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.4ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.5PART NUMBER BREAKDOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.6FACTORY CUSTOMER SERVICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.7PRODUCT WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 1.8REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 1.9FACTORY RETURNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 2INSTALLATION 2.1PRE-INSTALLATION CHECKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2.2INTERFACING WITH DATA EQUIPMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 DM-3422 (RF Board). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 3PROGRAMMING 3.1INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3.2DM3422 SYNTHESIZER DATA PROTOCOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 D-WORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 C-WORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 B-WORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 A-WORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 3.3RECEIVE TO TRANSMIT SEQUENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 3.4TRANSMIT TO RECEIVE SEQUENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 4CIRCUIT DESCRIPTION 4.1GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . β¦
Text truncated - open the document above for the full version.
T-96H Radio Modem Technical Manual version 0.01 PRELIMINARY The entire contents of this manual and the Radio Service Software described in this manual are copyright 1998 by DATARADIO Inc. Copyright DATARADIO Inc. August 1998 part no.: 120 10504-001 i Table of Contents 1.PRODUCT OVERVIEW............................................................................................................................1 1.1INTENDED AUDIENCE.................................................................................................................................1 1.2INTRODUCTION..........................................................................................................................................1 1.3GENERAL DESCRIPTION..............................................................................................................................1 1.4PHYSICAL DESCRIPTION..............................................................................................................................1 1.5CONFIGURATION........................................................................................................................................1 1.6CATALOG NUMBERS...................................................................................................................................2 1.7FACTORY TECHNICAL SUPPORT...................................................................................................................2 1.8PRODUCT WARRANTY................................................................................................................................2 1.9REPLACEMENT PARTS.................................................................................................................................2 1.9.1Factory Repair..................................................................................................................................2 1.10DIAGNOSTICS AND REMOTE COMMANDS.................................................................................................3 1.10.1Addressing....................................................................................................................................3 1.10.2Online Diagnostics.......................................................................................................................3 1.10.3Offline Diagnostics.......................................................................................................................4 1.10.4Remote Commands.......................................................................................................................4 1.11NETWORK CONFIGURATION....................................................................................................................4 1.11.1Basic Network...............................................................................................................................4 1.11.2Network Using T-Base..................................................................................................................5 1.11.3Network Using T-Base Repeater...................................................................................................5 1.11.4Network Using T-96H for Online Diagnostics...............................................................................6 2.FEATURES AND OPERATION................................................................................................................7 1.1OVERVIEW.................................................................................................................................................7 2.1INTENDED AUDIENCE.................................................................................................................................7 2.2FRONT PANEL............................................................................................................................................7 2.2.1LED Indicators.................................................................................................................................7 2.3DTE PORT INTERFACE...............................................................................................................................8 2.3.1RS-232 Inteface Signal Levels...........................................................................................................8 2.3.2Interface Port....................................................................................................................................9 2.3.3Interface Signal Description.............................................................................................................9 2.4CHANNEL SELECTION...............................................................................................................................10 2.5OPERATION..............................................................................................................................................10 2.5.1RTS/CTS Timing.............................................................................................................................11 2.5.2XTAL mode.....................................................................................................................................11 2.5.3Extended Turnoff............................................................................................................................11 3.ADJUSTMENTS AND MAINTENANCE................................................................................................12 1.1OVERVIEW...............................................................................................................................................12 3.1INTENDED AUDIENCE...............................................................................................................................12 3.2EQUIPMENT REQUIRED.................................................................................................................β¦
Text truncated - open the document above for the full version.
PHOTOGRAPHS: RULE PART NUMBER:2.983 (g)
FCC LABEL: RULE PART NUMBER:2.983 (f)
DESCRIPTION OF CIRCUITRY RULE PART NUMBER:2.983 (d)(10) THEORY OF OPERATION 1.0PURPOSE This report has been prepared to support the application for FCC Type Acceptance PER CODE OF FEDERAL REGULATIONS, TITLE 47, PARTS 2 AND 90 AND for the transmitter subsystem of the JDT Model 242-3422-XYZ Transceiver. The report presents necessary information concerning electrical circuit description, measured performance and physical construction and configuration. 2.0DL-3422 TRANSCEIVER The main subassemblies of this transceiver are the RF board, VCO board, TCXO and modem assembly. A block diagram of the transceiver is located in Figure 2. The VCO board is enclosed by a metal shield and soldered directly to the RF board. The VCO is not serviceable. The DL-3422 has a reference oscillator stability of Β±2.5 PPM. The 14.85 MHz TCXO (Temperature Compensated Crystal Oscillator) is soldered directly to the RF board. The TCXO is not serviceable. 2.1SYNTHESIZER The synthesizer output signal is produced by a VCO (voltage controlled oscillator). The VCO frequency is controlled by a DC voltage produced by the phase detector in U811. The phase detector senses the phase and frequency of the two input signals and causes the VCO control voltage to increase or decrease if they are not the same. The VCO is then "locked" on frequency. Programming of the synthesizer provides the data necessary for the internal prescaler and counters. One input signal is the reference frequency. This frequency is produced by the 14.85 MHz reference oscillator (TCXO). The other input signal is the VCO frequency. VOLTAGE-CONTROLLED OSCILLATOR Oscillator (Q872) The VCO is formed by Q872, several capacitors and varactor diodes, and air wound inductor L872. It oscillates at the transmit frequency in transmit mode and first injection frequency in the receive mode ( 132-174 MHz in transmit and 153.45 - 195.45 MHz in receive). Biasing of Q872 is provided by R873, R874 and R876. An AC voltage divider formed by C872, C874 and C875 initiates and maintains oscillation and also matches Q872 to the tank circuit. air wound inductor L872 is grounded at one end to provide shunt inductance to the tank circuit. Frequency Control and Modulation The VCO frequency is controlled by a DC voltage across varactor diodes CR852, CR853, and CR854. As voltage across a reverse-biased varactor diode increases, its capacitance decreases. Therefore, VCO frequency increases as the control voltage increases. CR852/CR853 and CR854 are paralleled varactors to divide the capacitance and improve linearity. The varactors CR852/CR853 are biased at -2.0V so the control line voltage can operate closer to ground. CR854 is pin shifted in when transmitting to increase the VCO gain in transmit. The control line is isolated from tank circuit RF by choke L852/L853. The amount of frequency change produced by CR852/CR853/CR854/ is controlled by series capacitor C854. The -2.0V applied to the VCO is derived from the 14.85 MHz TCXO frequency that is amplified by Q902, rectified by CR902 and filtered by C912, C917, C918 and C920 on the RF board. The VCO frequency is modulated using a similar method. The transmit audio/data signal from J201, pin 6 is applied across varactor diode CR861 which varies the VCO frequency at an audio rate. Series capacitors C855/C856 set the amount of deviation produced along with CR862 and C865. R863 provides a DC ground on the anodes of CR861/CR862, and isolation is provided by R862, and C863. The DC voltage across CR862 provides compensation to keep modulation relatively flat over the entire bandwidth of the VCO. This compensation is required because modulation tends to increase as the VCO frequency gets higher (capacitance of CR852/CR853/CR855 gets lower). CR862 also balances the modulation signals applied to the VCO and TCXO. The D/A Converter U911 can be programmed to apply a compensating voltage to CR862 to adjust the modulation sensitivity between the TCXO and VCO. The DC voltage applied across CR862 comes from the modulation adjust control R827 on the RF board. R826 applies a DC biasing voltage to CR86. C821 provides DC blocking. RF isolation is provided by C865, and R862. VCO AND REFERENCE OSCILLATOR MODULATION Both the VCO and reference oscillator (TCXO) are modulated in order to achieve the required frequency response. If only the VCO was modulated, the phase detector in U811 would sense the frequency change and increase or decrease the VCO control voltage to counteract the change (especially at the lower audio frequencies). If only the reference oscillator frequency is modulated, the VCO frequency would not change fast enough (especially at the higher audio frequencies). Modulating both VCO and reference oscillators produces a flat audio response. Potentiometer R827 sets the VCO modulation sensitivity so that it is equal to the reference oscillator modulation sensitivity. CASCADE AMPLIFIERS/VCO (Q871/Q872) The output signal on the collector of Q871 is coupled to buffer amplifier Q872 which forms a cascade amplifier. This is a shared-bias amplifier which provides oscillation, amplification and isolation from the stages which follow. The signal is coupled and matched from the collector of Q872 through inductors and capacitors and a T-pad to amplifier Q882. AMPLIFIER (Q882) Q882 provides final amplification of the VCO signal. Biasing of Q882 is provided by Q881 and several resistors. Matching to the transmitter and receive first injection is provided by L891 and C892. A 6dB T- pad is used to isolate the transmitter and receive first injection. VOLTAGE FILTER (Q901) Q901 on the RF board is a capacitance multiplier to provide filtering of the 8.6V supply to the VCO. R901 provides transistor bias and C901 provides the capacitance that is multiplied. If a noise pulse or other voltage change appears on the collector, the base voltage does not change significantly because of C901. Therefore, base current does not change and transistor current remains constant. CRβ¦
Text truncated - open the document above for the full version.
TRANSISTOR, DIODE, AND IC FUNCTIONS RULE PART NUMBER:2.983 (d)6) DL-3422 DesignatorPart NumberFunctionJEDEC or Vendor Type CR561523-1504-001Antenna switch MMBV3401 CR562523-1504-001Antenna switch MMBV3401 CR591523-1504-016Directional coupler MMBD701LT CR592523-1504-016Directional coupler MMBD701LT CR851523-1504-001Pin shift diode MMBV3401 CR852523-5005-023Rectifier MMBV609 CR853523-5005-023Rectifier MMBV609 CR861523-5005-022Varactor BB535E7908 CR862523-5005-022Varactor BB535E7908 CR901523-5005-022Varactor BB535E7908 CR902523-1504-023Rectifier BAV99LT1 Q101576-0013-046Tx enable MUN5213T1 Q102576-0013-032Tx enable MUN2114T1 Q121576-0013-046Rx enableMUN5213T1 Q122576-0013-046Rx enableMUN5213T1 Q123576-0013-032Rx enableMUN2114T1 Q124576-0006-027Soft key up controlPZT2222AT1 Q131576-0013-0465 volt shutdownMUN5213T1 Q171576-0013-046Pin shiftMUN5213T1 Q172576-0013-032Pin shiftMUN2114T1 Q501576-0003-640RF bufferMSA-2111 Q511576-0003-636RF driverNE85633 Q531576-0006-027Power control PZT2222AT1 Q801576-0013-701Constant voltage source MSD1819A-RT1 Q841576-0013-046Pin shiftMUN5213T1 Q842576-0013-032Pin shiftMUN2114T1 Q871576-0003-651VCO bufferNE85619-T1 Q872576-0003-651OscillatorNE85619-T1 Q881576-0013-700Bias regulator MSB1218A-AT1 Q882576-0003-636Amplifier NE85633 Q901576-0013-701Capacitance multiplier MSD1819A-RT1 Q902576-0003-634Amplifier MMBT918LT1 U111A544-2020-020Soft key up controlLMC660AMI U111B544-2020-020Soft key up controlLMC660AMI U111C544-2020-020Power controlLMC660AMI U111D544-2020-020Soft key up controlLMC660AMI U131544-2603-093Voltage regulatorTK11900MTL U141544-2603-093Voltage regulatorTK11900MTL U531544-4001-062RF power module M57732 U581A544-2019-017V-fwd ampMC33172DT U581B544-2019-017V-rev ampMC33172DT U811544-3954-027SynthesizerSA7025DK-T TRANSISTOR, DIODE, AND IC FUNCTIONS (continued) RULE PART NUMBER:2.983 (d)6) HNET MODEM Reference designatorFunctionType CZ1Transient Voltage Suppressor 5.6v, 0805VC080505A150 CZ2Transient Voltage Suppressor 5.6v, 0805VC080505A150 CZ3Transient Voltage Suppressor 14v, 0805VC080514A300 CZ6Transient Voltage Suppressor 14v, 0805VC080514A300 CZ7Transient Voltage Suppressor 14v, 0805VC080514A300 CZ8Transient Voltage Suppressor 14v, 0805VC080514A300 CZ9Transient Voltage Suppressor 14v, 0805VC080514A300 CZ10Transient Voltage Suppressor 14v, 0805VC080514A300 CZ11Transient Voltage Suppressor 14v, 0805VC080514A300 CZ12Transient Voltage Suppressor 14v, 0805VC080514A300 CZ4Transient Voltage Suppressor 5.6v, 0805VC080505A150 CZ5Transient Voltage Suppressor 5.6v, 0805VC080505A150 D1reverse power supply protection1N4001 D2reference settingBAV99LT1 D3TTL input protectionBAV99LT1 D4TTL input protectionBAV99LT1 D5TTL input protectionBAV99LT1 D6negative peak detectorMBD301LT1 D7positive peak detectorMBD301LT1 D8DIODE,ZENER 4.7vBZX84C4V7LT1 DS1Led, Narrow Beam, YellowHLMP-6400-010 DS2Led, Narrow Beam, RedHLMP-6000-010 DS3LED, Narrow Beam, GreenHLMP-6500-010 Q1LED SwitchMMBT3904LT1 Q2LED SwitchMMBT3904LT1 Q3LED SwitchMMBT3904LT1 Q4phase peak shape formatterMMBT3904LT1 Q5phase peak shape formatterMMBT3904LT1 U1RS-232 Driver/Receiver 5vMC145407DW U2Data Set (sync/async) InterfaceMC145428DW U4Undervoltage Sensing CircuitMC33064D U5Microprocessor ,QFP-8068HC711K4FU U6CPLD 64 Macrocell, Digital ModemPZ5064-I12A44 U7Dual , Op AmpLMC6484AIM U8Quad, Op AmpTLC2274I U9Digital PotentiometerAD8402AR50 U10Quad, Op AmpTLC2274I U11Analog Multiplexers/DemultiplexersMC74HC4053D U12Filter, Linear Phase Low PassLTC1069-7 U13Regulator, Micropower VoltageLP2951CD U14Regulator, Micropower VoltageLP2951CD TRANSMITTER TUNE UP PROCEDURE RULE PART NUMBER:2.983 (d)(9) TRANSMITTER TUNE UP PROCEDURE 1. Connect the transceiver to be aligned to a DC power source. A DC current meter capable of measuring at least 2.5 Amps should be connect in line with the DC source. Connect the output of the transceiver through a watt meter and into a 50 ohm dummy load. 2. Load the synthesizer with the center channel frequency. 3. Key the transmitter and make certain that the supply voltage at the RF board is 13.3 VDC. (Do not transmit for extended periods of time. ) 4. Adjust C525 clockwise for 5.0 Watts of output power. 5. Check the power levels on the low and the high frequencies for 5.0 Watts +/- 1 Watt.
EP531 PZT2222AT1 Q531 4 1 2 3 U111-C MC33174D 8 10 9 R537 51 JIC C219 CR563 JIC CW CCW 10K R805 CW CCW 100K R920 68K R263 33K R260 TP831 TP251 MH532MH534MH533MH531 MH105MH104MH103MH102REF1 TP801 TP281 6.8K R873 6.8K R816 6.8K R812 6.8K R814 68 R887 5.6K R126 560 R514 51K R133 47K R565 56 R896 47K R923 47K R922 47K R862 47K R861 4.7K R817 4.7K R811 4.7K R815 4.7K R813 4.7K R803 4.7K R511 4.7K R243 470 R533 470 R124 43K R112 39K R255 390 R876 39 R502 3.6K R125 33K R846 33K R806 33K R845 33K R266 3.3K R271 330 R233 330 R274 330 R275 330 R895 330 R915 270K R844 27K R807 2.7K R234 270 R305 270 R307 2.4K R272 22K R882 22K R808 22K R302 22K R832 22K R884 22K R259 22K R913 22K R304 22K R201 2.2K R205 20 R802 18K R265 1.8K R512 18 R306 18 R894 18 R893 18 R885 18 R892 18 R886 150K R883 150K R258 150K R116 150K R202 150K R303 150K R117 15K R134 15K R142 15K R917 1.5K R914 1.5K R916 1.5K R843 1.5K R852 150 R501150 R503 120K R828 11K R822 1.0 R208 1MEG R919 100K R121 100K R131 100K R253 100K R534 100K R141 100K R285 100K R284 100K R283 100K R829 100K R281 100K R821 100K R282 10K R536 10K R573 10K R912 10K R911 10K R113 10K R114 10K R115 10K R203 10K R171 10K R574 10K R286 10K R875 10K R874 10K R851 10K R583 10K R586 10K R826 10K R847 10K R921 10K R838 10K R804 10K R841 1K R592 1K R594 1K R901 1K R891 R204 1K 1K R872 1K R863 1K R308 1K R102 100 R257 100 R254 100 R881 100 R301 100 R515 100 R261 100 R842 10 R831 10 R871 10 R581 10 R513 10 R584 100 R562 100 R561470 R505 470 R504 120 R531 120 R532 51 R593 51 R591 82 R206 JIC R207 JIC R582 JIC R585 JIC R209 JIC R211 JIC R231 JIC R232 CW CCW 220K R827 CW CCW 20K R823 Q171 MUN5213T1 CW CCW 100K R825 CW CCW 100K R535 82nH L302 82nH L891 82nH L881 82nH L211 82nH L301 82nH L871 68nH L513 56nH L511 470nH L252 470nH L873 470nH L812 470nH L804 470nH L801 470nH L803 330nH L223 330nH L214 270nH L222 270nH L213 180nH L202 15nH L204 120nH L811 3.9uH L555 3.9uH L501 1uH L851 1uH L852 1uH L853 1uH L855 1uH L854 1uH L512 10T 43nH L561 10T43nH L554 10T43nH L552 10T43nH L551 10T43nH L553 4T 12.5nH L872 EP533 EP501 EP532 EP534 3.9pF C855C873 2.5-10pF C241 1.5-5pF 0.01 C115 0.01 C123 0.01 C104 0.01 C137 0.01 C111 0.01 C144 0.01 C233 0.01 C235 0.01 C143 0.01 C134 0.01 C251 0.01 C252 0.01 C265 0.01 C267 0.01 C268 0.01 C271 0.01 C272 0.01 C273 0.01 C275 0.01 C276 0.01 C246 0.01 C279 0.01 C302 0.01 C250 0.01 C513 0.01 C515 0.01 C523 0.01 C536 0.01 C543 0.01 C592 0.01 C594 C803 0.01 0.01 C804 0.01 C806 0.01 C801 0.01 C811 0.01 C812 0.01 C814 0.01 C841 0.01 C843 0.01 C845 0.01 C847 0.01 C849 0.01 C882 0.01 C902 0.01 C278 0.01 C912 0.01 C913 0.01 C915 0.01 C916 0.01 C921 0.01 C507 0.01 C911 0.01 C914 0.001 C557 0.001 C824 0.001 C822 0.001 C825 0.001 C815 0.001 C805 0.001 C802 0.001 C562 0.001 C581 0.001 C519 0.001 C593 0.001 C172 0.001 C503 0.001 C502 0.001 C501 0.001 C103 0.001 C101 0.001 C106 0.001 C517 0.001 C516 0.001 C306 0.001 C303 0.001 C301 0.001 C544 0.001 C545 0.001 C5240.001 C521 0.001 C146 0.001 C514 0.001 C232 0.001 C285 0.001 C284 0.001 C283 0.001 C282 0.001 C281 0.001 C201 0.001 C218 0.001 C212 0.001 C211 0.001 C209 0.001 C208 0.001 C112 0.001 C142 0.001 C136 0.001 C511 0.001 C591 0.001 C551 0.001 C534 0.001 C535 0.001 C533 0.001 C532 0.001 C531 0.001 C508 0.001 C813 0.001 C131 0.001 C133 0.001 C920 0.001 C124 0.001 C122 0.001 C842 0.001 C121 0.001 C893 0.001 C876 0.001 C850 0.001 C852 0.001 C848 0.001 C903 0.001 C891 0.001 C881 0.001 C871 0.001 C858 0.001 C844 0.001 C851 0.001 C846 0.001 C504 0.001 C266 0.001 C255 0.001 C163 0.001 C162 0.001 C161 0.001 C156 0.001 C155 0.001 C154 0.001 C153 0.001 C152 0.001 C151 68pF C542 68pF C506 68pF C875 56pF C234 47pF C244 47pF C874 39pF C872 330pF C253 330pF C918 27pF C223 27pF C215 27pF C213 220pF C259 220pF C809 220pF C854 22pF C505 22pF C203 22pF C207 C541 22pF 22pF C305 22pF C884 18pF C877 15pF C222 15pF C217 15pF C206 15pF C214 15pF C563 15pF C202 120pF C810 12pF C512 12pF C304 100pF C160 100pF C863 100pF C257 100pF C159 100pF C865 100pF C831 100pF C254 100pF C157 100pF C256 100pF C158 7.5pF C307 6.8pF C853 6.8pF C518 5.6pF C816 4.7pF C205 4.7pF C204 4.7pF C216 4.7pF C221 3.9pF C856 2.2pF C807 1.8pF C230 1pF C817 10pF C892 10pF C277 0.1 C114 0.01 C260 0.033 C832 0.0082 C116 0.0047 C836 0.01 C237 0.01 C245 27pF C883 0.001 C833 9.1pF C243 51pF C554 47pF C553 47pF C555 27pF C556 22pF C552 1.8pF C242 10pF C561 4.7 C901 1 C135 1 C826 1 C821 1 C102 1 C105 1 C125 C141 1 C522 1 C171 1 C145 47 C264 1 C917 JIC C584 JIC C583 JIC C800 JIC C582 JIC C258 JIC C861 JIC C864 JIC C862 JIC C231 MC33172D U581-C 4 GND 8 PWR MC33172D U831-C 4 GND 8 PWR U831-A MC33172D 1 3 2 MC33174D U111-E 11 GND 4 PWR MC14053B U913-D 6 _E 16 VDD 7 VEE 8 VSS Q881 MSB1218A Q882 NE85633 CR901 Q901 MSD1819A Q871 NE85619 Q872 NE85619 MMBV3401 35V CR851 CR862 2.1-18.7pF BB535 CR861 2.1-18.7pF BB535 MMBV609 CR853 MMBV609 CR852 Q842 MUN5114T1 CR902 MBAV99 Q172 MUN5114T1 Q173 MUN5213T1 Q841 MUN5213T1 Q902 MMBT918 MMBV3401 35V CR855 MMBV609 CR854 SA7025DK U811 544-3954-027 12 GND12 19 TEST 4 GND4 10 AUXIN 7 VCC7 6 _RFIN 18 LOCK 13 PHI 14 PHP 17 RF 11 PHA 1 CLOCK 2 DATA 8 REF_IN 9 RA 15 VCC15 5 RFIN 3 STROBE 20 VCC20 16 RN LMC7101 U801 1 4 5 GND 2 PWR 3 Y801 14.85MHz 1 MOD 14 VCC 8 OUT 18,17,20,19,16,15,7 GND Q801 MSD1819A MMBV3401 35V CR562 J501 1 4028 200V CR561 MC33172D U581-B 7 5 6 CR592 U581-A MC33172D 1 3 2 A531 3 FCPL 4 RCPL 6 OUT 5 GND 1 IN CR591 Q302 NE85633 Q301 MSB1218A M57732 U531 2 VCC1 3 VBB 1 RF_IN 5 RF_OUT 4 VCC2 Q511 NE85633 Q501 MSA2111 42 3 1 J201 Net Name14 J201 Net Name13 J201 Net Name12 J201 Net Name 11 J201 Net Name10 J201 Net Name9 J201 Net Name8 J201 Net Name7 J201 Net Name6 J201 Net Name5 J201 Net Name4 J201 Net Name3 J201 Net Name2 J201 Net Name 1 Q131 MUN5213T1 U141 2 SENSE 6 +5TAP 3 SD 7 FB 8 VCC 4 GND 5 _ERR 1 +5OUT U131 2 CONTROL 5 GND 4 VOUT 1 BYPASS 3 FEEDBACK 6 VIN Q101 MUN5213T1 Q102MUN5114T1 Q121 MUN5213T1 Q122 MUN5213T1 Q123 MUN5114T1 U111-A MC33174D 1 3 2U111-B MC33174D 7 5 6 U111-D MC33174D 14 12 13 PZT2222AT1 Q124 4 1 2 3 U912 4 Q0β¦
Text truncated - open the document above for the full version.
A Rev R9 47K R8 47K R11 100K R7 47K R12 100K R14 47K R22 220 R1647K R1947K R23 1K C14 22pF C15 22pF SW1A LD04H0SK 18 C10104 C21 104 C20 104 SW1D LD04H0SK 45 C5 104 SW1C LD04H0SK 36 SW1B LD04H0SK 27 C7 104 C16 104 R20 47K C6 104 C18 104 C17 104 D2 BAV99LT1 1 3 U3 AD22100AR V+ 1 VO 2 GND 4 R6 10K R3 1K R5 10K DS3 GREEN 21 Q3 MMBT3904 3 1 2 R18 10M Y1 9.8304MHZ 1 4 R13 470K R10 100K Q2 MMBT3904 3 1 2 DS1 YELLOW 21 R1 1K R2 1K R4 10K Q1 MMBT3904 3 1 2 DS2 RED 21 R21 10K R15 47K U1 145407 DO1 16 DO2 14 DO3 12 DI1 15 DI2 13 DI3 11 RX1 5 RX2 7 RX3 9 TX1 6 TX2 8 TX3 10 VCC 19 VDD 17 VSS 4 GND 2 C1+ 20 C1- 18 C2+ 1 C2- 3 C19 106 + C12 106 + C9 106 + C4 106 + C8 106 + C3 106 + U2 145428 TXS 1 TXD 2 RXD 11 RXS 12 DC 15 DIE 14 DOE 17 DCO 18 DCI 13 RST 19 DL 3 SB 9 CM 16 BR3 8 BR2 7 BR1 6 BC 5 BRCK 4 U5 68HC711K4FU 332-90807-100 XT 74 EX 73 RESET 75 IRQ 61 XIRQ 30 MODB 76 PA0 11 PA1 10 PA2 9 PE0 49 PE1 48 PE2 47 PE3 46 PE4 45 PE5 44 PE6 43 PE7 42 VRH 51 VRL 50 PA3 8 PA4 7 PA5 6 PA6 5 PA7 4 PB0 21 PB1 20 PB2 19 PB3 18 PB4 17 PB5 16 PB6 15 PB7 14 PC0 62 PC1 63 PC2 64 PC3 65 PC4 66 PC5 67 PC6 68 PC7 69 PD0 78 PD1 79 PD2 80 PD3 1 PD4 2 PD5 3 MODA 77 E 72 PG6 34 PG7 33 VSS 70 VSS 13 VSS 32 AVSS 52 AVDD 41 VDD 31 VDD 12 VDD 71 PG5 35 PG4 36 PG3 37 PG2 38 PG1 39 PG0 40 PH7 29 PH6 28 PH5 27 PH4 26 PH3 25 PH2 24 PH1 23 PH0 22 PF0 60 PF1 59 PF2 58 PF3 57 PF4 56 PF5 55 PF6 54 PF7 53 D3 BAV99LT1 1 2 3 D4 BAV99LT1 1 2 3 D5 BAV99LT1 1 2 3 C11 104 TP1 TP2 TP3 R17 4.7K U4 MC33064D IN 2 RST 1 GND 4 R57 1K R60 18K U6 PZ5064 332-90804-000 IN_1 11 IN_2 13 IN_3 16 A 18 B 19 C 28 F 25 INV 26 TX_/RX 27 TXD 7 TONE_EN 31 TST_TONE 29 G 32 CK_IN 43 RXS 1 OUT_1 12 OUT_2 14 OUβ¦
Text truncated - open the document above for the full version.
| # | Rule Parts | Frequency Range | Power Output | Emission | Tolerance |
|---|---|---|---|---|---|
| 2 | 90.21 | 132 MHz - 174 MHz | 5 W | 15K3F1D | 2.5 ppm |

Viper SC+ 928-960 MHz
Equipment Class
PCB - PCS Licensed Transmitter
VIPER SC+ 900 VHF 880-902 MHZ
Equipment Class
PCB - PCS Licensed Transmitter
VIPER SC+ 200 VHF 215-240MHZ
Equipment Class
TNB - Licensed Non-Broadcast Station Transmitter
UHF Wireless Radio Modem
Equipment Class
TNB - Licensed Non-Broadcast Station Transmitter
UHF Wireless Radio Modem
Equipment Class
TNB - Licensed Non-Broadcast Station Transmitter